Numerical Investigation of the Capture of Polydisperse Particles by Charged Droplets

The capture of particles by charged droplets was simulated by considering the electrostatic interactions of droplet-droplet and droplet-particle. The results indicate that the electrostatic repulsion between droplets leads to a dynamic accumulation mode of particles. However, the droplet spacing has an insignificant effect on the capture efficiency when the electrostatic deposition predominates. The increase of droplet charge remarkably improves the capture efficiency, in which the capture of fine particles accounts for the largest proportion. Compared to the droplet charge, the droplet size shows a limited improvement in the capture efficiency. Reducing the droplet velocity prolongs the capture time instead of enhancing the capture capacity per unit time, thereby improving capture efficiency.     

Crystallographic characteristics and microwave dielectric properties of Ni-modified MgTa2O6 ceramics

Ni²⁺ modified MgTa₂O₆ ceramics with a trirutile phase and space group P4₂/mnm were obtained. The correlations between crystallographic characteristics and microwave dielectric performance of MgTa₂O₆ ceramics were systematically studied based on the chemistry bond theory (PVL theory) for the first time. The results indicate that the introduction of Ni²⁺ causes a change in polarizability and the Mg–O bond ionicity, which contributes to the variation of dielectric constant. Moreover, the lattice energy, and packing fraction, full width at half maximum of the Raman peak of Ta–O bond, as the quantitative characterization of crystallographic parameters, regulate the dielectric loss of MgTa₂O₆ ceramics in GHz frequency band. In addition, the study of sintering behavior shows that the densification and micromorphology are the crucial factors affecting the microwave dielectric performance. Typically, Ni²⁺ doping on the A-site of MgTa₂O₆ can effectively promote the Q × f values to 173,000 GHz (at 7.43 GHz), which ensures its applicability in 5G communication technology.     

Investigation of crystal characteristics,Raman spectra,and microwave dielectric properties of Mg1-xZnxTa2O6 ceramics

Mg_(1-x)Zn_xTa₂O₆ (x = 0.00?0.08) dielectric ceramics were synthesized via the traditional solid-state reaction method. We used XRD and Rietveld refinement to demonstrate that a pure Mg_(1-x)Zn_xTa₂O₆ phase with trirutile structure was formed. Zn²⁺ substitution helped to decrease the Raman full width at half width of the A_1g mode at 703 cm^?1, which resulted in an increase in the order and rigidity of the TaO₆ octahedron, this in turn contributed to improving the Q×f values. Additionally, the introduction of Zn²⁺ significantly promoted grain growth and increased the dense, and the molecular polarizability, these factors lead to a higher permittivity. Moreover, enhanced Ta-O bond energy resulted in a more stable TaO₆ octahedron in the Mg_(1?x)Zn_xTa₂O₆ system, which contributed to enhanced τ_f values via substitution of Zn²⁺ doped on the A-site. Correspondingly, the microwave dielectric properties were significantly improved for 0.04-doped samples, obtaining: ε_r = 27, Q × f = 185,000 GHz (at 7.47 GHz), τ_f =32 ppm/°C.     

Study of haze emission efficiency based on new co-opetition data envelopment analysis

As haze intensifies in China, controlling haze emission has become the country's top priority for environmental protection. Because haze moves across different regions, it is necessary to develop a data envelopment analysis (DEA) model underpinned by both competition and cooperation to evaluate the haze emission efficiency in different provinces. This study innovatively adopts the spatial econometrics to construct the co-opetition matrices of Chinese provinces, then builds the co-opetition DEA model to evaluate the haze emission efficiency of them, and finally uses the haze data of 2015 as an example to assess the applicability of the model. The results of the study include the following: First, compared with the traditional CCR (A. Charnes & W. W. Cooper & E. Rhodes) model, this study constructs the co-opetition DEA cross-efficiency model that integrates haze's feature of cross-border moving; thus, it is more in line with the reality of haze emission and movement. Second, compared with the efficiency value gained from the CCR model, the haze emission efficiency values for Tianjin and Guangdong, two decision-making units, register greater variance when using the DEA model. The reason might lie in that they have a different spatial transportation relationship with their surrounding provinces. Third, the haze emission efficiency of provinces, according to the evaluation based on the co-opetition DEA method, varies greatly: Those with high efficiency are mostly inland provinces with slow economic growth and adverse climatic conditions, whereas many of the provinces with low efficiency are located in the relatively prosperous East China. The specific co-opetition DEA model constructed in this study enriches the research on the DEA model, which can be applied to the emission efficiency evaluation of similar pollutants around the world and can contribute empirical support to the haze reducing efforts of the government with its empirical results.     

Wear mechanism of a novel AlSiMgAl2O4Al2O3 composite used in the low vessel of an RH secondary refining furnace

A novel AlSiMgAl₂O₄Al₂O₃ composite brick was prepared and evaluated in the low vessel of an RH (the initials of Ruhrstahl and Hereaeus) secondary refining furnace; it was characterized by X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy. The results show that after use, the AlSiMgAl₂O₄Al₂O₃ composite has a functional gradient with an erosion zone–reinforced zone–original zone phase distribution, in which the phases in the erosion zone (0–1.8?cm) are a Mg-hercynite spinel solid solution, α-Al₂O₃, and minor amount of Al₃Fe₅O₁₂. Furthermore, the phases in the reinforced zone (1.8–5.0?cm) are γ-AlON, 21RSiAlON, SiC, Mg_0.388Al_2.408O₄, and α-Al₂O₃; i.e., the Al and Si in the composite are completely converted into non-oxide reinforced phases. Finally, the phases in the original zone (>5.0?cm) show no change. The reaction mechanism is as follows. During operation, a Mg-hercynite spinel solid solution is formed in the erosion zone due to a reaction between MgAl₂O₄ and FeO from a refinery operation. Therefore, the slag erosion of the material is improved. The Al and Si metals undergo active oxidation, and 21RSiAlON flakes are subsequently formed from the products of the metastable Al₂O(g), SiO(g), and N₂(g) in the ambient. The γ-AlON is formed by a carbothermal reduction nitridation of the α-Al₂O₃ and residual active carbon from the resin binder. The 21RSiAlON and γ-AlON reinforce the composite brick and improve its high temperature performance accordingly. Its service life is 110% that of the magnesia-chrome bricks used in the same period. The reaction model was also established.     

Chest X-ray images super-resolution reconstruction via recursive neural network

Multimedia Tools and Applications - To address the problems of insufficient detail extraction and long training time in the super-resolution reconstruction of chest X-ray images, a method of chest...     

Preparation and electrochromism of pyrochlore-type tungsten oxide film

Pyrochlore-type WO_3 powder was synthesized via hydrothermal method using aqueous sodium tungstate solution and oxalic acid as raw materials. The as-prepared powder was made into a soliquoid,from which films were made by dip coating process with indium-tin oxide(ITO).The obtained films were characterized by thermogravimetric and differential thermal analysis(TG-DTA), X-ray diffraction(XRD),scanning electron microscopy(SEM),transmission electron microscopy(TEM), cyclic voltammetry(CV), chronoamperometry(CA) and ultravioletvisible(UV-Vis) absorption. Results show that the crystal of the pyrochlore-type WO_3 powder is perfect. When the calcination temperature rises from room temperature to500 ℃,the pyrochlore-type structure first becomes deformed, then it is destroyed and turns into amorphous phase,finally it will completely convert to WO_3 with a monoclinic structure. Electrochemical and optical tests demonstrate that the film calcined at 300 ℃ exhibits the best electrochromic performance and has a coloration efficiency of up to 68.5 cm~2 C~(-1) at 884 nm.     

Fabrication of dense nano-laminated tungsten carbide materials doped with Cr3C2/VC through two-step sintering

This work investigates the critical roles of two-step sintering (TSS) and laminated structure on the sintering behavior and mechanical properties of functionally graded WC-TiC-Al₂O₃ nanostructured composite materials doped with Cr₃C₂/VC. Results show that excellent mechanical properties are achieved for tailored TSS conditions with a hardness of 27.91?±?2.3?GPa and a flexural strength of 1423.3?±?23.5?MPa. The desirable mechanical properties are attributed to the suppressed grain growth without densification deterioration. TSS is more effective in facilitating the favorable dispersion of secondary phase toughening nano-particulates in a WC matrix than conventional sintering (CS). Cr₃C₂/VC dopant plays an important role in maximizing and shifting the temperature range of the kinetic window for WC-Al₂O₃ composites. Al₂O₃ crack deflection, transgranular Al₂O₃, microcracking, WC crack bridging and plate-like WC crack deflection are the major toughening mechanisms. Residual surface compressive stress induced by the graded structure is also an appreciated contribution to the improvement of mechanical properties.     

Correlation between instrumental texture and colour quality attributes with sensory analysis of selected cheeses as affected by fat contents

This study evaluated several physical and sensory parameters of different types of cheese available in the Polish market. The measurements of textural properties were conducted in an Instron universal testing machine, while the colour properties of cheeses were measured using a Minolta chromameter. The chemical composition was determined by means of the near‐infrared spectroscopy (NIRs). Moreover, a trained sensory panel was invited to assess the cheese texture‐related properties. Generally, cheeses with reduced fat content were characterised by higher hardness, adhesiveness, cohesiveness and elasticity. Texture‐related parameters of cheese with canola oil were comparable to that of most of full‐fat cheeses. The correlation analysis between physical and sensory attributes related to cheese textural properties indicated the potential applications of TPA, shear and penetration tests (r = 0.766, r = 0.75 and r = 0.765, respectively) for the evaluation of sensory properties related to the hardness. Meanwhile, the elasticity of cheese obtained from sensory evaluation was strongly correlated with the elasticity determined from the shear test (r = 0.722) and moderately correlated with the elasticity from penetration test (r = 0.588), indicating a need to refine the method of penetration test. In addition, cheeses exhibited higher meltability during convection heating at 230 °C than microwave heating. The values of meltability for cheese with reduced fat content were lower than those of full‐fat cheese.