爆震室内混合物填充特性研究

爆震室内混合物的填充过程是PDE工作循环中的重要一环.为了研究爆震室内的燃料和氧化剂的填充特性,采用大型计算流体力学仿真软件对爆震室内燃料和空气的填充过程进行了数值模拟.计算结果表明,在设定的计算条件下,填充距离随填充时间的增加近似线形增大,填充完毕所需的填充时间约0.125s,且从距封闭端250mm开始,填充后的乙炔质量分数稳定在0.11.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

Controlled Synthesis of Ag2S,Ag2Se,and Ag Nanofibers by Using a General Sacrificial Template and Their Application in Electronic Device Fabrication

Nanofiber bundles of Ag₂S, Ag₂Se, and Ag have been successfully synthesized by making use of Ag₂C₂O₄ template nanofiber bundles, utilizing both anion‐exchange and redox reactions. The obtained bundles were polycrystalline nanofibers composed of nanoparticles in which the precursor morphology was well‐preserved, indicating that Ag₂C₂O₄ nanofiber bundles acted as a general sacrificial template for the synthesis of silver‐based semiconductor and metal nanofibers. Dispersing media and transforming reactants were found to be key factors influencing the chemical transformation in the system. In particular, separate single‐crystalline Ag nanofibers were obtained via a nontemplate route when ascorbic acid was used as a relatively weak reductant. An electrical transfer and switching device was built with the obtained Ag₂S and Ag nanofiber bundles, utilizing the unique ion‐conductor nature of Ag₂S and revealing their potential applications in electronics.     

负载型固体催化剂在生物柴油制备中的研究现状及应用前景

对生物柴油及其制备方法进行简单介绍，重点综述了负载型固体酸、碱催化剂在生物柴油制备中的研究现状，并指出当前负载型固体催化剂研制中的研究热点，最后对其应用前景了进行展望。     

用VB解决CAI中的几个问题

本文利用Windows的API函数将VB窗体前置,避免教师在CAI过程中频繁切换活动窗口,并通过VB控件将各种不同的电子文档内容在窗体中显示出来。     

MIP-CGP工艺专用催化剂CGP-1的开发与应用

阐述了生产汽油组分满足欧Ⅲ排放标准并多产丙烯的催化裂化工艺（简称MIP-CGP）专用催化剂（简称CGP-1）的研究开发与工业应用结果。CGP-1催化剂的基质具有良好的容炭性能，使活性组元受到良好保护，其优势作用在第二反应区得以充分发挥，具有更高的氢转移活性和强的汽油小分子烯烃裂化活性。中国石化九江分公司和镇海炼化公司的MIP-CGP工业试验标定结果表明，与常规FCC相比，采用CGP-1催化剂的MIP-CGP技术在生产烯烃体积分数小于18％的汽油组分的同时，丙烯产率达到8％以上。此外，汽油诱导期大幅提高，抗爆指数增加；总液体收率有所提高，干气产率下降，焦炭选择性良好。     

Global Asymptotical Synchronization of Chaotic Lur'e Systems Using Sampled Data: A Linear Matrix Inequality Approach

Sampled-data feedback control for master-slave synchronization schemes that consist of identical chaotic Lur'e systems is studied. Sufficient conditions for global asymptotic synchronization of such chaotic Lur'e systems are obtained using the free-weighting matrix approach and expressed in terms of linear matrix inequalities (LMIs). With the help of the LMI solvers, the sampled-data feedback control law can easily be obtained to globally asymptotically synchronize Lur'e chaotic systems. The effectiveness of the proposed method is finally illustrated via numerical simulations of chaotic Chua's circuits.     

Tri-Gate Bulk MOSFET Design for CMOS Scaling to the End of the Roadmap

A tri-gate bulk MOSFET design utilizing a low-aspect-ratio channel is proposed to provide an evolutionary pathway for CMOS scaling to the end of the roadmap. 3-D device simulations indicate that this design offers the advantages of a multi-gate FET (reduced variability in performance and improved scalability) together with the advantages of a conventional planar MOSFET (low substrate cost and capability for dynamic threshold-voltage control).     

Automating application software generation

Many approaches have been proposed to enhance software productivity and reliability. These approaches typically fall into three categories: the engineering approach, the formal approach and the knowledge-based approach. But the optimal gain in software productivity cannot be obtained if one relies on only one of these approaches. This paper describes the work in knowledge-based software engineering conducted by the authors for the past 10 years. The final goal of the research is to develop a paradigm for software engineering which integrates the three approaches mentioned above. A knowledge-based tool which can support the whole process of software development is provided in this paper.     

苏北-南黄海盆地构造演化

苏北及南黄海盆地是由多期、多类盆地叠加的复合残留盆地,地质概况基本相似,成因演化近同,自元古界下扬子板块形成后,主要经历了古-中生代地台、中生代前陆盆地、走滑拉分盆地时期以及新生代断陷、坳陷盆地时期.在古生代-中生代发展过程中是一个整体,晚白垩世盆地演化出现分化,发育伸展盆地群,形成一系列叠置在中、古生代盆地之上的箕状断陷,箕状断陷的发育及分布明显受中-古生界内部先存逆冲断裂的控制.