退火对直流磁控溅射铬膜附着性的影响

为了利用铬膜改善锆的抗腐蚀性，研究了退火对Zr-2基体上制备的直流磁控溅射铬膜附着性的影响，使用扫描电镜（SEM）观察了界面形貌及锆，铬的界面的分布，用X－射线衍射仪（XRD）分析了膜层的组成，用划痕法测定了铬膜的附着，结果表明，锆／铬界面结合良好，边界可见；与现有文献比较，获得的铬膜附着性好――均超过20N；溅射后退火使Zr-Cr界面更像扩散界面，但X－射线衍射结果未发现有界面反应产物；退火提高铬膜与Zr-2基体的附着性约50％，扩散际着附着性增加的主要因素。     

双BGO晶体能谱测井

Ｃ／Ｏ测井可以利用ＢＧＯ晶体探测效率高的特点，在其探测器部分放置两个探测器，称为双探测Ｃ／Ｏ测井仪，长短源距两个探头所测谱数据进行补偿，有效地去除了井眼条件的影响，提高了测量精度和油水差值，更加有产地分油水层，并有望能在低孔隙度的地层中使用Ｃ／Ｏ测井仪器。     

A novel integrated silicon capacitive microphone-floating electrode“electret” microphone (FEEM)

A novel principle “electret” microphone, i.e., floating electrode electret microphone, is proposed and implemented in this study. Single-chip fabrication and corrugation technique are used in the design and fabrication of the microphone. The floating electrode is encapsulated by highly insulated materials to ensure that there is no electric-leakage passage between the floating electrode and the electrodes of the microphone. Net-free electronic charges (not “bonded” charges as in traditional electret) in the floating electrode can excite the electric field, which is similar to that of the traditional electret. The floating electrode can be easily charged by use of the “hot” electron technique, available using the avalanche breakdown of the p⁺-n junction. Therefore, the electret microphone is rechargeable, which can greatly increase the lifetime of the device. The preamplifier has been on-chip integrated in a junction-field-effect transistor (JFET) source-follower type with resistors by use of ion implantation. Electret charges are banded in a deep potential trap, thus, this microphone can operate at a high temperature (as high as 300°C) and has high stability and reliability. Experiments show that the prototype has a 3-mV/Pa sensitivity and a larger than 21-kHz frequency bandwidth in a 1 mm ×1-mm diaphragm area. Microphone performance can be further improved by optimized process and design. The fabrication is completely integrated-circuit (IC) compatible, hence, the microphone shows promise in integrated acoustic systems     

贵州电力调度交换网络平台组建经验

从贵州电力调度交换网络平台建立的迫切性出发，介绍了贵州电力调度交换网络平台组建的方案及实施情况，以及对网络的维护管理经验，并对联网中遇到的具体问题进行了详细的分析。     

试论徐志摩散文特色

徐志摩以诗歌创作饮誉文坛,而他的散文创作亦有很高的成就。徐志摩散文个性化色彩强烈,自成一体。众多现代散文名家对徐志摩的散文给予了高度评价。试从写作风格、意境和人生感受等三方面阐述徐志摩散文特色。     

BT20钛合金低温铣削试验研究

为改善钛合金工件的加工表面质量,进行了低温铣削钛合金试验,并得出了合理的切削用量。     

原水浊度与混凝剂最佳投量的匹配

本文在试验的基础上。推导了原水浊度与混凝剂最佳投量之间的关系。得到了潭江水泵用碱式氯化铝作混凝剂时的最佳投量与浊度之间的半经验关系A=1.1C~(0.40)(mg/l)。     

谐振式变换器电路结构分析

本文着重对电压源串联型谐振变换器的理论问题和电路结构作了分析，对电流源并联型谐振变换器也作了概略的介绍。     

Gaussian process assisted coevolutionary estimation of distribution algorithm for computationally expensive problems

In order to reduce the computation of complex problems, a new surrogate-assisted estimation of distribution algorithm with Gaussian process was proposed. Coevolution was used in dual populations which evolved in parallel. The search space was projected into multiple subspaces and searched by sub-populations. Also, the whole space was exploited by the other population which exchanges information with the sub-populations. In order to make the evolutionary course efficient, multivariate Gaussian model and Gaussian mixture model were used in both populations separately to estimate the distribution of individuals and reproduce new generations. For the surrogate model, Gaussian process was combined with the algorithm which predicted variance of the predictions. The results on six benchmark functions show that the new algorithm performs better than other surrogate-model based algorithms and the computation complexity is only 10% of the original estimation of distribution algorithm.     

TC4合金锥体模锻过程的数值模拟

采用刚塑性有限元法对钛合金锥体的模锻成形进行有限元数值模拟,分析了锥形件模锻过程中的金属流动规律,应力场、应变场、变形区的压力分布,压力的变化规律等。模拟结果表明,锥体模锻成形分为3个阶段:初期变形过程是圆柱体变形为一个小曲率壳体的阶段,应力主要集中在上模的正下方,应变主要发生在此变形区;变形中期是与下模相接触的部分参与变形的体积逐渐增大,直至最后形成所需要的锥体形状;变形后期由于摩擦作用产生严重的不均匀壁厚减薄现象。