OSF:一种支持SaaS应用的构件框架

离线SaaS应用可以工作在时断时续的网络连接环境下,是一种环境可感知的智能SaaS软件.目前支持离线访问Web应用的研究成果较少,且其没有考虑到SaaS的特性,更没有形成构件化框架.为了解决上述问题,提出了离线SaaS框架OSF(Offline SaaS Framework),并给出了支持离线访问的面向操作的构件框架的结构和运行机制.通过案例描述验证了该构件框架的功能和性能.理论和实验表明,离线SaaS应用框架极大地改善了用户体验,保证了SaaS服务的可用性,扩大了SaaS的应用范围,同时还提高了系统开发效率.     

玻璃中离子注入的进展

玻璃中离子注入的进展王承遇，王波，陶瑛（大连轻工业学院玻璃及无机新材料研究所１１６００１）ＴｈｅＤｅｖｅｌｏｐｍｅｎｔｏｆＩｏｎ－ＩｍｐｌａｎｔｉｏｎｉｎＧ１ａｓｓｅｓ￥ＷａｎｇＣｈｅｎｇｙｕ；ＷａｎｇＢｏ；ＴａｏＹｉｎｇ（ＩｎｓｔｉｔｕｔｅｏｆＧｌ...     

Preparation of BaTiO3-Based Nonreducible X7R Dielectric Materials Via Nanometer Powders Doping

Nonreducible X7R dielectric materials, which can be cofired with Ni electrode, were obtained by doping nanometer additives to BaTiO₃ powders synthesized by employing a sol-gel method. The crystallization process, structure and constituent of nanometer additives, as well as morphologies were studied via differential thermal and thermogravimetric analyses (DTA/TG), X-ray diffraction (XRD) and transmission electron microscopy (TEM). The effects of the calcining temperature of dopants on the dielectric properties were also discussed. The experiment results proved that higher-performance X7R dielectric materials could be obtained via nanometer doping compared with conventional doping. At room temperature, dielectric constant is more than 3000; dielectric loss lower than 1.0% and insulation resistance more than 10¹¹Ω ⋅cm.     

Machinability of Metal Matrix Composites Reinforced by 3-D Network Structure

Metal matrix composites reinforced by three-dimensional (3-D) continuous network structure reinforcement (3DCNRMMC) are difficult to machine due to serious tool wear and poor surface roughness caused by the brittle and hard reinforcement which interpenetrate into ductile matrix. In order to achieve the approach of low cost of 3DCNRMMC, the machinability of it needs to be understood. The influences of three cutting parameters and volume fraction of reinforcement on cutting force were analyzed in detail. The results indicate that: (1) Due to the brittle phase(s) introduced into ductile matrix of composites, there is a large fluctuation of cutting force causing deterioration of machinability. The fluctuation ranges of cutting forces, initially increase rapidly with the increase of volume fraction of reinforcement and then decrease finally, are largest at the range of the volume fraction of 55–65%; (2) The influence of cutting parameters on cutting force is obvious. With the increases of cutting speed, cutting force decreases gradually unless cutting speed exceeds the value of 209 m/min. Cutting forces increase with increasing feed rate and depth of cut; (3) Owing to the large fluctuation of cutting force, there were some cratered surfaces caused by Si₃N₄ reinforcement pulling-out and flaking-off. Some brittle phase protruding from the machined surface caused the deterioration of machined surface.     

超细片状铝粉和铝银浆的制备

超细鳞片状铝粉和铝银浆由于其特殊的二维平面结构，具有良好的遮盖力、显著的屏蔽效应、光学反射能力；超细鳞片状铝粉和铝银浆颜料的制备方法很多，本文采用机械化学法制备超细鳞片状铝粉和铝银浆。     

语言在网络语境中的变异

本文从词形变异、语义变异、语法变异三个方面分析了语言在网络语境中的变异及变异的原因,并指出,网络语言的变异已辐射到网络之外的语境中。作者还就如何看待网络语言的变异提出了一些看法。     

多元回归分析在电热式平板硫化机热板温度场中的应用

分析电热平板硫化机热板温差大的主要影响因素,重点研究热源分布情况对温差的影响.以400×400电热平板硫化机为例,应用多元回归的二次响应曲面模型及其子模型,对热源间距(电热管间距)与热板表面最大温差之间的函数关系进行预测,检验并分析预测结果(拟合曲线)的可靠程度,从而得出较合理的数学模型,即完整二次响应曲面模型.此模型可为工程设计提供参考依据.     

A 3-GHz 70-mb SRAM in 65-nm CMOS technology with integrated column-based dynamic power supply

Column-based dynamic power supply has been integrated into a high-frequency 70-Mb SRAM design that is fabricated on a high-performance 65-nm CMOS technology. The fully synchronized design achieves a 3-GHz operating frequency at 1.1-V power supply. The power supply at SRAM cell array is dynamically switched between two different voltage levels during READ and WRITE operations. Silicon measurement has proven this method to be effective in achieving both good cell READ and WRITE margins, while lowering the overall SRAM leakage power consumption.     

基于C8051f020的标准电源控制单元的设计及实现

介绍了基于C8051f020的程控标准电源的控制部分。该控制单元以C8051f020为核心实现了PID控制器及人机交互的设计,并给出了具体实现方法,同时在实际电路的调试中收到了良好的效果。     

锰含量对超细晶粒C-Mn钢显微组织和机械性能的影响

研究了锰含量对两种超细晶粒C-Mn钢(碳含量为0.2%)显微组织和机械性能的影响.大压下量温变形和连续退火可形成超细晶粒显微组织,最终钢的显微组织由含有细小渗碳体颗粒的超细粒状铁素体组成.渗碳体颗粒内锰富集,因此,铁素体晶粒的平均尺寸随锰含量的增加而减小(锰含量从0.74%增加到1.52%时,晶粒尺寸由1.3μm减小到0.8μm).锰含量越高,晶粒越细.延展性和韧性相同的情况下,增加锰含量将提高钢的强度.