Preparation and properties of PET/PA6 copolymer/montmorillonite hybrid nanocomposite

From in situ polycondensation, a poly(ethylene terephthalate)/Polyamide 6 copolymer/montmorillonite nanocomposite was prepared, after the treatment of montmorillonite (MMT) with a water soluble polymer. The resulting nanocomposites were characterized by X‐ray diffraction (XRD), differential scanning calorimeter (DSC), nuclear magnetic resonance (NMR), dynamic mechanical analysis (DMA), and transmission electron microscopy (TEM). The results of DSC, ¹H NMR, and DMA proved that the nanocomposite synthesized was PET/PA6 copolymer/MMT nanocomposite, not the PET/PA6 blend/MMT nanocomposite. The results of XRD and TEM proved that the dispersion of MMT was improved observably after the introduction of PA6 molecular chain into PET. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2512–2517, 2006     

Numerical Simulation of Oil‐water Hydrocyclone Using Reynolds‐Stress Model for Eulerian Multiphase Flows

A three‐dimensional oil‐water turbulent flow and oil separation process in a double‐cone liquid‐liquid hydrocyclone (LLHC) is numerically simulated using FLUENT software. The Euler‐Euler approach and Reynolds‐stress model are combined and adopted in this simulation to handle the challenging situation of anisotropic turbulent two‐phase flow with a higher volumetric ratio (over 10%) in the dispersed phase. It is visualized well in the simulation how separation, aggregation and shift of oil and water proceed in the LLHC. The oil separation efficiency is determined based on flow field and phase concentration distribution. The simulation is verified by comparing predicted and measured separation efficiency in the LLHC.     

使用KQ-1缓蚀阻焦剂,减轻糠醛装置腐蚀和结焦

独山子炼油厂糠醛精制装置设备腐蚀状况严重 ,尤其是加工高酸值原料 ,更加剧了设备的腐蚀。通过对腐蚀原因分析 ,决定从工艺防腐上解决 ,提出了加入缓蚀剂减缓设备腐蚀的方法 ,在实验室评价和工业装置中 ,评选了四种糠醛精制装置的缓蚀剂 ,其中KQ 1作为装置缓蚀剂效果最佳 ,平均缓蚀率达到 4 4 .5 % ,并估算了KQ 1工业使用的经济效果     

Manipulating the microstructure and rheology in polymer‐organoclay composites

A series of nanocomposites prepared by melt‐blending of cloisite‐based organoclays with poly(ethylene‐vinylacetate) (EVA) and neutralized poly (ethylene‐methacrylic acid) (EMA) copolymers were investigated via DSC, small‐angle X‐ray scattering (SAXS), and rheological techniques. SAXS results indicated partial clay exfoliation in all samples. In both EMA and EVA systems, the nominal melting temperature T_m and bulk crystallinity are not significantly affected by the presence of organoclays, suggesting that clay particles are predominantly confined in the amorphous phase. In rheological measurements (above T_m), the EVA‐clay system demonstrated a solid‐like rheological behavior under the small‐strain oscillatory shear, yet it was able to yield and flow under a steady shear, which is the characteristic of physical crosslinking. In contrast, the EMA‐clay system exhibited a melt‐like rheological behavior, where the influence of organoclay on the thermorheological behavior of the EMA composite was quite minimal. We propose that the carbonyl groups of vinylacetate in EVA interact with the clay surface, resulting in a strong physically crosslinking like interaction in the melt. On the other hand, the interaction between EMA and clay is weak because of repulsion between carboxyl anions and negatively charged clay surface.     

浅谈高校后勤的科学化与精细化管理

科学化管理是精细化管理的前提,精细化就是按照统筹兼顾原则把科学管理要求落实到管理的各个环节.在高校后勤推行科学化、精细化管理,目的是进一步提高后勤为学校教学、科研服务的水平和质量.为此,高校后勤要加强制度建设,提高管理规范化水平;加强管理人员培训工作,提高后勤队伍的整体素质;建立和完善监督制约机制,形成对后勤管理与服务工作的有效的监控体系.     

影响株洲火车站广场空气质量的因素研究

为了探究影响火车站广场污染物(总悬浮颗粒物和可吸入颗粒物)质量浓度的因素,以株洲火车站广场为研究对象,对总悬浮颗粒物和可吸入颗粒物质量浓度与人流密度、车流量的变化关系进行了试验性研究。结果表明,总悬浮颗粒物质量浓度与人流密度、车流量都呈正相关,其主要影响因素是车流量;可吸入颗粒物质量浓度与人流密度呈正相关,与车流量不呈明显的正相关,其主要影响因素是人流密度。细菌和病毒以可吸入颗粒物为载体被人体吸入而致病,因此人们活动时应尽量避开广场人流密度大的地方。     

轴向开槽对改善超磁致伸缩材料线性度影响的研究

磁致伸缩应变与磁场关系的非线性,影响了磁致伸缩控制元件的精度和稳定性。文章针对这一问题,在超磁致伸缩式微小型高速开关阀驱动部件设计基础上,提出了沿超磁致伸缩棒(GMM)轴向开槽的方法来改善GMM部件的工作性能。通过对轴向开槽前后GMM棒内部磁场强度和焦耳热分布的数值计算,分析了轴向开槽对改善磁场强度的分布和减少热损耗功率的影响,通过对GMM棒开槽前后伸缩量的测试,验证了开槽可以明显改善超磁致伸缩材料组件的非线性。     

琥珀酰亚胺酯基类偶氮染料的制备及其超临界CO2羊毛清洁化染色

以对氨基苯甲酸和4-氨基-2-氯苯甲酸、苯胺和间甲苯胺为原料,采用重氮偶合反应制备染料前驱体,通过在前驱体上引入琥珀酰亚胺酯获得4例活性分散染料Ⅰ～Ⅳ.对染料的紫外-可见吸收光谱、光热稳定性、超临界二氧化碳(scCO2)中羊毛纤维的染色工艺等进行了测试.结果表明,4例染料均具有良好的光热稳定性,染料Ⅰ、Ⅲ和Ⅳ最大吸收波长集中在360～370 nm,染料Ⅱ的最大吸收波长红移到379～452 nm,染料均具备scCO2染色的条件.染料Ⅰ和Ⅲ的最佳染色条件为2 h、80℃和15 MPa,染料Ⅱ的最佳染色条件为1.5 h、80℃和15 MPa,染料Ⅳ的最佳染色条件为2 h、80℃和24 MPa.染色后的羊毛纤维的耐皂洗和耐光色牢度都可达4～5级,固色率最高可达86％,相比于未活化的前驱体,耐皂洗色牢度能提高2～3级,固色率最高能提升63％.SEM和显微镜成像证明4例染料具有良好的透染性,且能均匀附着于纤维的表面和内部.力学性能测试表明,染色后的羊毛纤维能基本保持原有的力学性能.     

Thermogravimetric analysis of methyl methacrylate‐graft‐natural rubber

The thermal degradations of methyl methacrylate‐graft‐natural rubber (MG) at different heating rates (B) in nitrogen were studied by thermogravimetric analysis. The results indicate that the thermal degradation of MG in nitrogen is a one‐step reaction. The degradation temperatures increase along with the increment of heating rates. The temperature of initial degradation (T₀) is 0.448B + 362.4°C, the temperature at maximum degradation rate, that is, the peak temperature on a differential thermogravimetric curve (T_p) is 0.545B + 380.7°C, and the temperature of final degradation (T_f) is 0.476B + 409.4°C. The degradation rate at T_p is not affected by B, and its average value is 48.9%; the degradation rate at T_f is not affected by B either, and its average value is 99.3%. The reaction order (n) is 2.1 and is not affected by B. The reaction activation energy (E) and the frequency factor (A) increase along with B, and the apparent reaction activation energy (E₀) is 254.6 kJ/mol. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2952–2955, 2002     

"计算机网络基础"课程"金课"建设初探

为了响应教育部关于建设"金课"的倡议,基于我院计算机科学与技术专业的"计算机网络基础"课程特点,结合该专业的毕业要求,修订了课程目标;根据课程目标,重新整合了教学内容,确定了线上线下混合式教学模式;构建课程目标达成度评价体系,并将其用于后续教学过程.实践结果表明,该教学改革符合混合式"金课"的建设要求,提升了教学效果.