高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

Application of a multi-channel system for continuous monitoring and an early warning system.

A multi-channel continuous toxicity monitoring system developed in our laboratory, based on two-stage mini-bioreactors, was successfully implemented in the form of computer-based data acquisition. The multi-channel system consists of a series of a two-stage minibioreactor systems connected by a fiber optic probe to a luminometer, and uses genetically engineered bioluminescent bacteria for the detection of the potential toxicity from the soluble chemicals. This system can be stably and continuously operated due to the separation of the culture reactor from the test reactor and accomplish easy and long-term monitoring without system shut down by abrupt inflows of severe polluting chemicals. Four different recombinant bioluminescent bacteria were used in different channels so that the modes of the samples toxicities can be reasonably identified and evaluated based upon the response signature of each channel. The bioluminescent signatures were delivered from four channels by switching one at once, while the data is automatically logged to an IBM compatible computer. We also achieved the enhancement of the system through the manipulation of the dilution rate and the use of thermo-lux fusion strains. Finally, this system is now being implemented to a drinking water reservoir and river for remote sensing as an early warning system.     

Effects of hot-carrier stress on high performance polycrystalline silicon thin film transistor with a single perpendicular grain boundary

This paper is a report on the effect of a single perpendicular grain boundary on the hot-carrier and high current stability in high performance polycrystalline silicon (poly-Si) thin film transistors (TFTs). Under a hot carrier stress condition (Vg = Vth + 1 V, Vd = 12 V), the poly-Si TFT with a single grain boundary is superior to the poly-Si without any grain boundary because of the smaller free carriers available for electric conduction. The shift of transconductance in poly-Si TFT with a single grain boundary is less than 5% after hot carrier stress during a period of 1000 s. The shift of transconductance is about 25% in the case of the poly-Si TFTs without a grain boundary in the channel. On high current stress, the poly-Si TFT without the grain boundary is less degraded than the poly-Si TFT with the grain boundary because the concentrated electric field near the drain junction is lower.     

Pulse stabilisation in harmonically FM modelocked erbium fibre ring laser with DFBLD

A new pulse stabilisation scheme for a harmonically frequency modulated (FM) modelocked erbium fibre ring laser using a distributed feedback laser diode (DFBLD) is presented. More than 65 dB supermode noise suppression in the RF spectrum was obtained with the proposed method. Effective reduction of supermode noise can be accomplished as the DFBLD in the fibre laser acts not only as a fast-gain saturated medium but also as an optical bandpass filter for suppressing supermode noise in a harmonically modelocked laser system.     

A simple mathematical analysis on the effect of sand in Cr(VI) reduction using zero valent iron

A simple mathematical model was proposed to analyze the enhancement of Cr(VI) reduction when sand materials are added to the zero valent iron (ZVI). Natural decay of Cr(VI) in a control experiment was analyzed by using a zero-order decay reaction. Adsorption kinetics of Cr(VI) to sand was modeled as a first-order reversible process, and the reduction rate by ZVI was treated as a first-order reaction. Natural decay of Cr(VI) was also included in other experiments, i.e., the adsorption to sand, the reduction by ZVI, and both adsorption and reduction when sand and ZVI are present together. The model parameters were estimated by fitting the solution of each model to the corresponding experimental data. To observe the effect of sand addition to ZVI, both adsorption and reduction rate models were considered simultaneously including the natural decay. The solution of the combined model was fitted to the experimental data to determine the first-order adsorption and reduction rate constants when sand as well as ZVI is present. The first-order reduction rate constant in the presence of sand was about 35 times higher than that with ZVI only.     

交流变频调速采用“△”脉宽调制的参数选择

本文在增量调制的原理基础上,对“△”脉宽调制的原理及实质进行了实验分析与研究。从理论上论证了“△”调制方案的合理性。通过实验对“△”调制所提供的满足变频调速要求的控制特性及设计思想的可行性进行了验证。着重对参数选择进行了实验分析,指出了参数选择的观点及其依据。按本文的观点选择参数,在工程应用中是切实可行的。     

Effects of surfactant/silica and silica/cerium ratios on the characteristics of mesoporous Ce-MCM-41

Using the surfactant CTMABr (cetyltrimethyl ammonium bromide) and cerium(IV) sulfate, mesoporous Ce-MCM-41 molecular sieves were produced under a hydrothermal condition with various surfactant/silica (surfactant/Si) and silica/cerium (Si/Ce) ratios. Changes to the structural traits caused by changing the molar ratios of both surfactant/Si and Si/Ce were investigated. XRD (X-ray diffraction), FT-IR (fourier transform infrared spectroscopy), and SEM (scanning electro microscopy) were used for the characterization of prepared mesoporous samples. Among the tested molar ratios, surfactant/Si ratio of 0.5 and 0.2 showed highest values of d_1 0 0 and intensity, respectively, for the Si-MCM-41. XRD analysis also identified a quintessential hexagonal structure of Ce-MCM-41 for the Si/Ce molar ratio higher than 40 (maintaining the surfactant/Si ratio at 0.2). When cerium content was increased to have the Si/Ce molar ratio of 20, the hexagonal structure of Ce-MCM-41 was collapsed due to the structural stress of substituted cerium. FT-IR results confirmed calcination of Ce-MCM-41 and the incorporation of Ce⁴⁺ ions of cerium sulfate into the silica surface with proper removal of the surfactant. Rod-like shape with rounded edges of the prepared Ce-MCM-41 samples was identified by SEM. These results suggest surfactant/Si ratio of 0.2 and Si/Ce ratio of 40 for the production of Ce-MCM-41 with the highest level of crystallinity.