A new approach to two-machine flow shop problem with uncertain processing times

This paper deals with the problem of optimization of job sequence in a two-machine flow shop problem in the presence of uncertainty. It is assumed that the processing times of jobs on the machines are described by triangular fuzzy sets. A new optimization algorithm based on Johnson”s algorithm for deterministic processing times and on an improvement of McCahon and Lee”s algorithm is developed and presented. In order to compare fuzzy processing times, McCahon and Lee use mean values of their corresponding fuzzy sets. It is shown that this approach cannot fully explore possible relationships between fuzzy sets. In order to overcome this drawback we consider different fuzzy sets determined by λ-cuts of the fuzzy processing times. Extensive experiments show that the new algorithm gives better solutions with respect to makespan than existing McCahon and Lee's algorithm.     

Machinability of Metal Matrix Composites Reinforced by 3-D Network Structure

Metal matrix composites reinforced by three-dimensional (3-D) continuous network structure reinforcement (3DCNRMMC) are difficult to machine due to serious tool wear and poor surface roughness caused by the brittle and hard reinforcement which interpenetrate into ductile matrix. In order to achieve the approach of low cost of 3DCNRMMC, the machinability of it needs to be understood. The influences of three cutting parameters and volume fraction of reinforcement on cutting force were analyzed in detail. The results indicate that: (1) Due to the brittle phase(s) introduced into ductile matrix of composites, there is a large fluctuation of cutting force causing deterioration of machinability. The fluctuation ranges of cutting forces, initially increase rapidly with the increase of volume fraction of reinforcement and then decrease finally, are largest at the range of the volume fraction of 55–65%; (2) The influence of cutting parameters on cutting force is obvious. With the increases of cutting speed, cutting force decreases gradually unless cutting speed exceeds the value of 209 m/min. Cutting forces increase with increasing feed rate and depth of cut; (3) Owing to the large fluctuation of cutting force, there were some cratered surfaces caused by Si₃N₄ reinforcement pulling-out and flaking-off. Some brittle phase protruding from the machined surface caused the deterioration of machined surface.     

60000m^3／h空分设备快速变工况生产的操作探讨与实践

为降低60000m^3／h空分设备的氧气放散率，武钢氧气公司实施了空分设备的手动快速变工况生产。分析了空分设备运行工况不稳定和自动变工况系统难以实施的原因，介绍了手动快速变工况的理论依据、前期准备工作和实施过程，阐述了手动快速变工况实施进程中应注意的事项。     

The effect of carbon precursor on the pore size distribution of mesoporous carbon during templating synthesis process

The starch and cyclodextrin were selected as the precursors and the mixture of surfactant and tetraethyl orthosilicate (TEOS) as template to prepare mesoporous carbon. The result showed that a bimodal pore size distribution in mesoporous carbon derived from starch appeared; one was around 3.4 nm and the other ranged from 3.8 to 16.2 nm. However, there existed a concentrated pore size distribution from 3.2 to 4.2 nm in mesoporous carbon derived from cyclodextrin. The different molecular structure of starch and cyclodextrin and their polymerization process in the presence of sulfur acid were responsible for the resulted mesoporous carbon structure; the starch could polymerize by head to head or side by side, but the cycleodextrin was only polymerized by head to head.     

Growth and optical characterizations of (Ba0.32Sr0.68)5Nb4O15 crystal

(Ba_0.32Sr_0.68)₅Nb₄O₁₅ crystal with sizes of Ø 17 × 35 mm was grown successfully by Czochralski technique method. The thermal anisotropy was discussed. The principal coefficients of thermal expansion along (100), (010), (001) directions were precisely measured to be 1.308 × 10^− 5, 1.288 × 10^− 5, 1.478 × 10^− 5 K^− 1, respectively. Its optical transparency range has been measured and found to span from 323 to 5500 nm. The bands present in the IR spectra were identified and assigned to the corresponding vibration modes of NbO₆ anions.     

Influence of cathodic current on composition, structure and properties of Al2O3 coatings on aluminum alloy prepared by micro-arc oxidation process

Alumina coatings on aluminum alloy were prepared by micro-arc oxidation (MAO) process using DC and AC power supplies, respectively. In comparison with the coating deposited by DCMAO, the influence of the cathodic current on the composition, structure and properties of the ACMAO coating was investigated. It is found that the coating deposited by DCMAO is composed of α-Al₂O₃, whereas the coating deposited by ACMAO has a mixture composition of α-Al₂O₃ and γ-Al₂O₃. The results of properties show that compared with the coatings deposited by DCMAO, the ACMAO coatings possess higher density, hardness and corrosion resistance. It can be attributed to that the DCMAO coating is rougher and existing much more micro-cracks in its inner layer. As a result, the adhesion of the DCMAO coating to the substrate decreases.     

基于MCS-51单片机的家庭安防电话委托系统的设计

本文介绍了一种以MCS-51单片机为微控制器的家庭安防电话委托系统，给出了系统的原理图，单机与语音芯片的硬件连接图以及系统部分软件流程图。     

Resonance properties and mass sensitivity of monolithic microcantilever sensors actuated by piezoelectric PZT thick film

The PZT thick film cantilever devices fabricated via MEMS process have much attraction because they are appropriate for biological transducer or sensor, resulting from their large actuating force and relatively high sensitivity especially in liquid. By means of resonance behavior, theoretical calculation and experimental verification of the PZT thick film cantilever devices have not been studied before. Accordingly, we focused on the sensitivity analysis and interpretation of the PZT thick film cantilevers in this study. Especially, the investigation for mass sensitivity of the PZT thick film cantilever is of importance for physical, chemical and biological sensing application. The PZT thick film cantilever devices were constructed on Pt/TiO₂/SiN _X /Si substrates using screen printing method and MEMS process. The harmonic oscillation response (resonance frequency) was measured using an optical laser interferometric vibrometer. The effect of cantilever geometry on the resonance frequency change was investigated. Compared with the theoretical resonant frequency change by mass loading, the experimental resonant frequency change of the PZT micromechanical thick film cantilever shows a variation of less than 2%. Mass sensitivities are estimated to be 30.7, 57.1 and 152.0 pg/Hz for the 400 × 380 μm, 400 × 480 μm and 400 × 580 μm cantilever, respectively.