Laser-assisted sealing and testing for ceramic packaging of MEMS devices

In this work, a CO/sub 2/ laser-assisted silicon lid sealing process, utilizing Au80/Sn20 solder, for encapsulating gas breakdown test micro-electro-mechanical structures (MEMS) in a ceramic quad flatpack (CQFP) was studied. Wire bonded MEMS dies were sealed into CQFPs under various gas media, such as air, nitrogen, helium and vacuum. The gas breakdown test results showed a significantly higher breakdown voltage for vacuum packaged parts compared to those packaged in other various gas environments. Hermeticity testing according to MIL-STD-883E showed that the leak rate of the package was below 10/sup -8/ atm cc/s. The bonding was uniform and the bonding strength is believed to be comparable to the tensile strength of Au80/Sn20 solder.     

Phase Transition VO2 Thin Films for Optical Switches

This paper presents a method to make vanadium dioxide (VO₂) crystallites on silicon substrates by reactive ion beam sputtering. The thickness of the thin film is about 100nm. The phase transition temperature of VO₂ is 65°C. The transmittance of the semiconducting phase VO₂ is about 50% and it is reduced to as low as 3% in metal phase at the infrared wavelenghth spectrum. The extinction ratio of the optical switches is 12dB. and the insertion loss is of 1-2dB. The switching time is about 1ms.     

27keV Ar~+斜入射时的Cu-Au合金溅射实验角分布

用27keV Ar~+分别在垂直和倾斜入射情况下,轰击了Cu-Au(30wt％)合金样品,测量了Cu和Au原子的溅射角分布。角分布是用卢瑟福背散射(RBS)技术分析Al捕获膜上的Cu-Au沉积成分而定量得到的。结果表明:(1)在Ar~+倾斜(θ=40°)入射时,Cu原子择优发射,且程度比垂直入射(θ_r=O°)时增强:(2)倾斜入射时,Cu原子的角分布显示出在接近于样品表面法线方向的发射角范围内(θ<45°),发射机率比垂直入射时减小。     

傅立叶变换在虚拟仪器LabVIE中的应用

文中介绍了LabVIEW环境下用NI公司高级分析库里的信号处理工具包的Real FFT.vi傅立叶变换,采用此种方法对某型飞机起落架液压测试系统采样信号进行频谱分析,实验证明其效果良好.     

铸造铝合金(ZL109)激光表面处理

采用功率为2kW级CO_2连续可调式横流激光光源,对不同涂层的ZL109试样表面进行了激光熔凝的实验研究。     

A vectorial boundary element method analysis of integrated optical waveguides

In this paper, a new vectorial boundary element method is introduced and applied to the modal analysis of dielectric waveguides with piecewise homogeneous refractive indexes. The procedure, which is free of spurious modes, determines the full field distribution from the longitudinal fields at the refractive index boundaries. Singular kernels are evaluated through series solutions while the electric field discontinuity at corners is accommodated through either a grid refinement technique or a semianalytic approach. Our formalism generates propagation constants and modal field distributions for several representative refractive index profiles with far higher accuracy than standard finite-difference or finite-element procedures.     

High‐Tg Carbazole Derivatives as Blue‐Emitting Hole‐Transporting Materials for Electroluminescent Devices

A series of dicarbazolyl derivatives bridged by various aromatic spacers and decorated with peripheral diarylamines were synthesized using Ullmann and Pd‐catalyzed C–N coupling procedures. These derivatives emit blue light in solution. In general, they possess high glass‐transition temperatures (T_g > 125 °C) which vary with the bridging segment and methyl substitution on the peripheral amine. Double‐layer organic light‐emitting devices were successfully fabricated using these molecules as hole‐transporting and emitting materials. Devices of the configuration ITO/HTL/TPBI/Mg:Ag (ITO: indium tin oxide; HTL: hole‐transporting layer; TPBI: 1,3,5‐tris(N‐phenylbenzimidazol‐2‐yl)benzene) display blue emission from the HTL layer. The EL spectra of these devices appear slightly distorted due to the exciplex formation at the interfaces. However, for the devices of the configuration ITO/HTL/Alq₃/Mg:Ag (Alq₃ = tris(8‐hydroxyquinoline)aluminum) a bright green light from the Alq₃ layer was observed. This clearly demonstrates the facile hole‐transporting property of the materials described here.     

水电站施工期水土流失预测

水电站建设的水土流失问题主要体现在施工期和运行期，并以施工期的影响较为突出．如不采取必要的减免措施，将会对周围生态环境造成无法挽回的损失。本文阐述了水电站建设水土流失的几种常用的预测方法，对水土流失量进行预测，并结合具体工程实例对水电站建设过程中新增水土流失量进行了预测。     

3DFD Simulation of Asymmetric Wave Field by Side-wall Acoustic Tool in Open and Cased Wells

1. Introduction Side-wall acoustic logging tools, such as the Segmented Bond Tool (SBT) from Baker Atlas and the tools for open hole measurements, utilize acoustic transducers mounted on six pads to make compensated acoustic velocity and attenuation measurements which are not affected by mud weight, gas cut, fast formation effects, casing surface conditions or reasonable tool de- centralizing. Studies on the wave fields generated by these tools are very important to tool design and data int…