新型高k栅介质材料研究进展

随着半导体技术的不断发展，MOSFET（metal-oxide-semiconductor field effect transistor）的特征尺寸不断缩小，栅介质等效氧化物厚度已小至nm数量级。这时电子的直接隧穿效应将非常显著，将严重影响器件的稳定性和可靠性。因此需要寻找新型高k介质材料，能够在保持和增大栅极电容的同时，使介质层仍保持足够的物理厚度来限制隧穿效应的影响。本文综述了研究高k栅介质材料的意义；MOS栅介质的要求；主要新型高k栅介质材料的最新研究动态；展望了高k介质材料今后发展的主要趋势和需要解决的问题。     

基于数字信号处理器的直流电机控制系统

介绍了定点数字信号处理器（DSP）TMS320F240的一般性能及其在永磁无刷直流电机控制上的应用，给出了硬件设计方案、软件策略及输出结果。     

Cif2000平台下的核磁共振测井解谱方法研究

介绍了在Cif2000多井解释平台下的核磁共振解谱方法与编程实现。解谱采用加入平滑因子后在特征矩阵的奇异值分解中截去小的非零奇异值的方法，可以在低信噪比时得到稳定的弛豫谱，在油田实际应用中证明了该方法的有效性。根据该方法在Cif2000平台上编制了完整的解谱处理程序，可以直接用于油田的生产实际。     

第三代短波自动链路建立系统特性分析及仿真实现

分析了第三代短波自动链路建立系统的工作特性及技术特点，并对系统仿真实现的原则及一些细节问题进行了较深入的探讨，同时对仿真实现中涉及的链路质量分析（LQA）算法进行了研究。     

Improvement of RCA transistor using RTA annealing after theformation of interfacial oxide

A polysilicon emitter RCA transistor (an ultra-thin interfacial oxide layer exists between polysilicon and silicon emitter) is presented which can operate at 77 K for the first time. An ultra-thin (1.5 nm) interfacial oxide layer is grown deliberately between polysilicon and silicon emitter using RCA oxidation and excellent device stability is obtained after rapid thermal annealing (RTA) treatment in nitrogen atmosphere. The RCA transistor exhibits good electrical performance at very low temperature for an emitter area of 3 × 8 μm². The maximum toggle frequency of a 1:2 static divider is 1.2 GHz and 732 MHz at 300 K and 77 K, respectively     

TP130TT高抗挤套管研究与应用

为了提高盐层段固井质量 ,中原油田研究开发了 TP130 TT高抗挤套管 ,性能试验评价表明 ,其抗挤强度超过 16 0 MPa,并给出了其固井质量评价标准。在中原油 346口井中的应用表明 ,该套管有效地解决了盐层段套管损坏问题 ,延长了油气水井寿命 ,经济效益和社会效益显著。     

Interfacial strength and chemistry of additive-free silicon nitride ceramics brazed with aluminium

Two kinds of additive-free silicon nitride ceramics were brazed with aluminium; one was with as-ground faying surfaces and the other was with faying surfaces heat-treated at 1073K for 1.8 ksec in air. The heat-treatment of the silicon nitride ceramics formed a silicon oxynitride layer on the faying surfaces and increased the brazing strength of the joints. A silica-alumina non-crystalline layer and a β′-sialon layer were formed successively from the aluminium side at the interface of the joints. The heat-treatment which made the former layer thicker is a necessary process in making reliable, strong brazed joints.     

In-Situ observation on microfracture behavior ahead of the crack tip in 63Sn37Pb solder alloy

in-situ transmission electron microscopy (TEM) tensile tests on as-cast and aged 63Sn37Pb solder alloys were conducted, and the fracture behavior in nanometer scale ahead of the crack tip was inspected and discussed. Results show that the fracture was completed by connecting the discontinuous cracks or voids. Dislocation behavior was concentrated along the grain boundaries for as-cast samples, and displayed mainly as dislocation climb. The crack was intergranular dominated under the lower strain rate. While remarkable mutual dislocation emission was detected in the aged solder. Transgranular cracks were dominant in the fractured area, and they propagated by linking up with the nanometer scale cracks ahead of the crack tips under the effective promotion of the inverse dislocation emission. At the same time, the partial interphase or intergranular cracks in the thinned area were also found. Under this condition, a new critical stress intensity factor K _c ^′ to define the mutual dislocation emission was proposed.     

Enhancing echo cancellation via estimation of delay

The advent of packetized audio transmission, such as voice over IP (VoIP), has resulted in challenging requirements for echo cancellation technology. One key aspect of this technology is the need to characterize, quickly and accurately, the echo paths in the transmission media. Echo paths consist of a constant time delay with no echo signal and active regions in which the echo signal is present. When an adaptive filter echo cancellation algorithm is used, its performance can be greatly increased, and its complexity can be reduced if it is only applied to the active regions. This requires an algorithm to estimate the constant delay and locate the active regions. Traditionally, delay estimation has been based on direct application of cross-correlation. This method has poor performance because the input signals are highly correlated and has a high implementation cost because many cross-correlation lags have to be computed for longer time delays. The delay estimation addressed in this paper has two major advantages over the traditional methods. The first is that it has improved performance because the input signals are processed to have less correlation. The second is that the implementation cost is significantly reduced because fewer cross-correlation lags are computed, and an efficient method to estimate lags is created.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。