富氧燃烧技术在梭式窑中的应用

研究了富氧燃烧技术对梭式窑烧成的影响.研究结果表明,随着氧浓度从21%-30%的逐渐增加,CO总浓度和NO总浓度都先明显下降,后缓慢上升;节能效果在初始段较为明显,而后效果不明显;而实际烟气量与氧浓度成反比,与过剩空气系数成正比.     

调整水量法(代用法)测定水泥标准稠度用水量方法的改进

结合兰州市的水泥标准稠度用水量方法测定 (代用法 )的实例 ,分析代用法测定标准稠度用水量的缺点 ,并对此方法提出了一些改进措施     

Two-dimensional symmetric multimode interferences in silicon square waveguides

Symmetric interference in two-dimensional multimode silicon waveguides is experimentally investigated. For a 100/spl times/100 /spl mu/m/sup 2/ cross section, 2700-/spl mu/m-long waveguide fabricated on silicon-on-insulator substrate, an 8/spl times/8 matrix of replicated images with high contrast ratio is demonstrated for 1530-1570 nm wavelength range. Symmetric interference results in reduced device length, and the actual device length is consistent with the theoretical expectation. The device also exhibits stable imaging in terms of good loss uniformity, and low wavelength and polarization dependencies among the replicated images.     

IF钢冷轧及再结晶初期微观组织的TEM研究

采用透射电子显微镜对不同压下量和再结晶初期的IF钢样品进行了研究．结果表明：无论是在较小形变量下还是在较大形变量下，形变不均匀性是普遍存在的；冷变形程度不同，织构组分不同，TEM形貌也不同；在再结晶的最初期，冷轧的形变组织演变为近乎等轴的亚晶，优先形成{111}〈uvw〉取向的晶核，晶核逐渐吞并周围的形变基体而长大，最终形成再结晶γ-纤维织构．     

Growth of highly orientated strontium barium niobate thin films on Si substrates through the sol–gel process using a K: SBN template layer

We report the growth of highly C-axis orientation of Sr _x Ba_1−x Nb₂O₆ (SBN) thin films on p-type (100) Si substrates by using a potassium-substituted SBN template layer with the sol–gel method. The crystallization of SBN thin films was found closely related to the potassium ion doping concentration and the postannealing temperature of the K-SBN template layer. Secondary ion mass spectrometry analysis showed that potassium elements were accumulated at the interface of the template layer and silicon substrate. SBN films postannealed at 750 °C with K-SBN template layer has a smaller full width at half maximum of X-ray rocking curve of 2.45° than that of 5.40° for the pure SBN films. By introducing a template layer, the surface morphologies of SBN films fabricated on silicon substrate were greatly improved.     

Verification of submodeling technique in thermomechanical reliability assessment of flip-chip package assembly

In this paper we verified the submodeling technique applied in the thermomechanical reliability assessment of a flip-chip BGA under accelerated thermal cycling test conditions. Since the steady-state creep model was implemented for the solder bump to better represent its realistic mechanical behavior, submodeling procedures developed specifically for path-dependent thermomechanical problems were considered. A detailed global model for the flip-chip BGA was built up to verify submodeling solutions. This model also served as a benchmark to examine solution discrepancies caused by different simplifications of the global model.     

超分子主体化合物在分析化学中的应用研究进展

综述了近年来超分子主体化合物在分析化学领域的应用研究与进展。分别以冠醚、环糊精、杯芳烃、卟啉4类超分子为主体功能化合物的研究进行了详细的评述，并对这几类主体化合物在分析化学中的应用研究进行了展望。     

压电量测系统漏电影响分析

本文通过对压电量测系统等效电路图的逐步简化,得出矩形脉冲信号的漏电方程;并对系统在各种情况下的时间常数,漏电相对误差进行了计算,最后就系统在校准和现场测试中经常碰到的几种情况,进行了定量估算,从而解决了压电量测系统在使用中的一些具体问题。     

一种新型陶瓷材料及其耐磨性

对新型Ａｌ２Ｏ３－ＴｉＣ－Ｃｏ陶瓷的磨粒磨损，冲蚀磨损及其在单颗粒作用下的摩擦磨损行为进行了研究。与ＡＴ３０（７０ｗｔ％Ａｌ２Ｏ３－３０ｗｔ％ＴｉＣ）陶瓷相比，Ａｌ２Ｏ３－ＴｉＣ－Ｃｏ陶瓷具有更为良好的耐磨性，金属钴的存在提高了基体的韧性，细化了晶粒，其综合力学性能得到了显著提高，ＡＴＣ陶瓷样品耐磨性与其强韧化水平和细致的组织结构有关。     

新型超微晶软磁合金FePCCuMoSi微观结构缺陷的正电子湮没研究

用正电子湮没方法研究了新型超微晶软磁合金的微观结构缺陷，样品选用的是在不同温度下退火的Ｆｅ８１Ｐ１２Ｃ３Ｃｕ１Ｍｏ０．５Ｓｉ２．５合金，结果表明，合金的微观结构构陷大小，密度随退火温度有规律地变化，这种现象可能与非晶的晶化过程有关。