论滚齿加工在机测量技术

本文论述了滚齿在机测量中一些重要问题．应用偏心误差理论，揭示了以齿轮的齿顶、齿根和内孔为测量基准的测量齿距误差的实质，并对这三种基准进行了对比分析．指出了不同测量基准所测结果不同，若基准选择不当，有时产生“误收”或“误废”．论文针对当前滚齿在机测量装置存在问题．提出了一种滚齿在机１８０°转位双啮综合测量法，测量原理正确，结构简单，易于推广．     

聚碳硅烷的分子量分布与可纺性研究

阐述了聚碳烷的合成及其分子量分布，讨论了高低分子含量对聚碳硅烷熔点及可纺性的影响，而且提出了分子量分布的控制标准与方法。     

GaAs Mach－Zehnder型光波导开关／调制器

采用非对称Ｘ结耦合器代替传统的Ｙ分支器，研制了ＧａＡｓＭａｃｈ－Ｚｅｈｎｄｅｒ型２×２光开光，得到了小于－２２．４ｄＢ的串音比和１２Ｖ左右的开关电压，器件的波导传输损耗小于７ｄＢ／ｃｍ。预计该器件可广泛应用于ＧａＡｓ开关列阵及高速光调制等领域。     

弹丸外弹道优化设计初始点的选取

在弹丸外弹道优化设计中,需对优化设计变量赋于初始值.初始值选取得如何,对整个优化计算所耗机时、迭代点收敛到哪个极值点上等等,影响很大.该文对初始值的选取原则、选取方法等作了讨论,所得结果也可作为对弹丸主要结构参数选优的预估.     

Simulation of the pressure set-point change transient with the Kuosheng plant analyzer

The purpose of this paper is to simulate the pressure set-point change transient with the Kuosheng plant analyzer. The Kuosheng plant analyzer was developed for the Kuosheng nuclear power station based on the boiling water reactor plant analyzer of the Brookhaven National Laboratory and the Chinshan plant analyzer of the Taiwan Power Co. First, the pressure control system (PCS) model was verified on a stand-alone basis, with the sensed dome pressure test signal as the input variable. Then, a transient induced by a step change in the pressure set-point was simulated with the Kuosheng plant analyzer and compared with the test data. The predicted results of the main system variables showed good agreement with the test data-within 8% of the maximum relative deviation. In addition, the PCS performance of the Kuosheng nuclear power station was analyzed.     

Multiple respiratory gas monitoring causes changes of inspired oxygen concentration in closed anesthesia system

This case report describes an accessory hepatic duct (AHD) identified by intraoperative cholangiography during excisional surgery of a choledochal cyst (CC). The accessory duct was divided and reconstructed successfully to the Roux-en-Y jejunal loop. The postoperative course was uneventful, and follow-up abdominal sonography revealed neither evidence of biliary tract obstruction nor atrophic changes of the liver. It is advocated that an AHD should be meticulously reconstructed if it is divided during excisional surgery of a CC.     

地面驱动单螺杆泵杆柱的组合设计

根据地面驱动单螺杆泵的工作特点，分析了传递动力的抽油杯柱受力状况，认为抽油杆柱受复合载荷的作用，在承受扭矩的同时承受较大的轴向力，给出了各种载荷的计算方法。由第四强度理论，提出了把抽油杯柱设计成两级杆柱的等强度组合设计方法，即先按要求及标准确定两级杆柱的直径和长度，然后扶强度条件进行校核。根据油田的实际情况，编制了抽油杆柱电算程序，并给出了设计训一算实例。     

分子振动态及其跃迁的激光相干控制

讨论了激光合成相干叠加态的原理及其性质 ,针对 XY2 型分子 ,证明了合成局域模振动的可行性 ,然后给出相干叠加态的跃迁几率特征 ,发现它仍表现出相干的特性 ,对之进行分析研究表明 ,分子的振动态具有可控性 ,态跃迁几率具有可控性。