Oxidation Performance of Fe-Al/WC Composite Coatings Produced by High Velocity Arc Sprayed at 650 ℃

Fe-Al intermetallics with remarkable high-temperatureintensity and excellent erosion,high-temperatureoxidation and sulfuration resistance are potential lowcost high-temperature structural material.ProducingFe-Al/WC composite coating by high velocity arcspraying(HVAS)on structural materials would notonly obviate the problems faced in fabrication of thesealloys into useful shapes,but also allow the effectiveuse of their outstanding high-temperature performance,which might thus promisingly mak…     

用含Pb、As、Sn地方生铁砂型铸造生产D型石墨铸铁的研究

基于Ph、As、Sn等元素有增大铁液过冷倾向的作用，利用含Ph、As、Sn的地方生铁，采用合金化和砂型铸造可以获得D型石墨铸铁，对其工艺方案进行了研究。用正交试验法设计试验方案，得到最佳工艺方案为：在亚共晶成分（WB％：3．2C，2．1si）的铁液中加入适量的铝（0．6％）和钛（0．8％），可以得到含有100％D型石墨的铸铁，其抗拉强度最高可达276MPa。     

坯料外形对镁合金矩形盒拉深成形的影响

用商业有限元软件模拟了在同一套模具和成形条件下不同毛坯外形的镁合金矩形盒拉深成形过程．依据数值模拟结果，分析了不同坯料外形对镁合金矩形盒拉深成形的影响。结果表明：使用矩形圆角坯料比其他坯料的成形性能好。     

圆锯片的有限元模态分析

针对金属冷热锯机锯片在锯切轧件过程中出现的振动问题 ,利用 MSC/ NASTRAN有限元软件 ,计算分析了各种参数对锯片模态的影响。从而为锯片的设计及其制造工艺的确定提供了可靠的参考依据 ,为最终解决生产中的实际问题发挥了重要作用     

钨钴硬质合金电化学蚀刻加工研究

对YG6硬质合金电化学蚀刻工艺进行了研究,提出了采用光致抗蚀剂作保护膜,在生成一定钝化膜的情况下进行电化学蚀刻的方法.在一定的蚀刻深度范围内,该工艺的可控性好、腐蚀区表面质量较好.     

Ultrahigh Current Density Ion Implantation

A study of several engineering alloys implanted at ultrahigh current densities has revealed that the process induces no change in the bulk microsctructure of the materials. Even though temperatures induced during processing exceed the transformation (tempering and annealing) temperatures, there is insufficient time for nucleation and growth reactions to occur during the temperature excursion associated with typical implantation dose and energy conditions. Substantially lower costs should accompany the shorter duration ultrahigh current density implantation process. Auger electron spectrographs reveal a substantially extended nitrogen range over those observed at low current densities (four-fold increase). This enhanced range appears to be due to radiation enhanced diffusion effects. Deeper penetration could lead to more durable surface layers.     

(Short communication) Degradation of corrosion resistance of Zircaloy-4 in LiOH aqueous solution

To investigate the degradation of corrosion resistance of Zircaloy-4 in LiOH aqueous solution, SIMS (secondary ion mass spectrometry) analysis was performed to examine the profiles of Li~ , K~ , and OH~- in oxide layers formed in the same concentration (0.1 mol/L) LiOH and KOH solutions. Even though the oxide layers have an equal thickness, the penetration depth of K~ is shallower than that of Li~ , and the penetration depth of OH~- corroded in KOH solution is also shallower than that corroded in LiOH solution. It shows that the diffusion of OH~- into oxide layer is accompanied by the corresponding cation. The difference of degradation effect of LiOH and KOH solutions on the corrosion resistance of Zircaloy-4 was discussed.     

基于I2C总线技术的等离子喷焊系统的研究

阐述了基于I^2C总线技术的等离子喷焊过程控制系统的设计原理，介绍了软硬件及接口设计技术。实践表明，采用I^2C总线技术，不仅使系统的芯片大大减少，系统的灵活性增强，而且提高了系统的抗干扰能力。     

Experimental Study of Microstructure Evolution during Tempering of Quenched Steel and Its Application

LARGE-SIZED FORGINGS are usually intensivelyquenched to obtain the desired microstructuredistribution,high strength and hardness.Becauseresidual stresses are high in quenched large-sizedforgings,tempering processes follow quenchingprocesses to reduce the residual stress and obtain goodmechanical properties.Several differentmicrostructures are generated in quenched steelforgings,such as martensite,bainite and retainedaustenite.Modeling of microstructure evolution inquenched steel during …     

椭圆弧数控代码的自动生成方法

提出了一种基于计算机辅助制造的数控加工代码自动生成的方法，着重阐述了该方法针对椭圆弧的数控代码自动生成过程。该方法通过分析加工图形的dxf文件，提取图形的坐标信息，再经过数据拟和，自动生成该图形的数控代码。该方法由VC＋＋6．0实现相应的功能，经实际运行表明，能满足加工精度要求。该方法摆脱了传统数控机床从加工图形到形成数控加工代码时间长且精度不高的缺点，极大她提高了工作效率。