DMFC阳极催化剂用GRQD-NiCo2O4复合物的制备与电催化活性分析

采用水热法制备GRQD-NiCo₂O₄复合物,利用XRD、SEM及TEM分析其微结构,并探讨其作为DMFC阳极催化剂使用时的电化学性能。微结构分析表明所得GRQD-NiCo₂O₄复合物皆为具NiCo₂O₄单一相的尖晶石结构,且GRQD质量浓度高于0.25 g/mL后表面形貌将转变GRQD与NiCo₂O₄相互结合的状态。电化学分析表明添加GRQD可有效增强NiCo₂O₄的导电性并提升其电化学稳定性,其中GRQD质量浓度为0.25 g/mL时所得样品经500次循环测试后电流密度约为77.5 A/g,与循环5次后相比其电流密度剩余量最大（约为69.7%）,该样品作为DMFC阳极催化剂使用时性价比最佳。     

磷石膏提质降杂实验研究

磷石膏的综合利用对保护环境、促进企业可持续健康发展具有重要意义,但是磷石膏中的磷、氟、二氧化硅等杂质影响其利用。针对云南磷石膏中二氧化硅含量高的问题,采用正浮选工艺开展了磷石膏提质降杂的实验研究。通过单因素条件实验获得了合适的工艺参数：浮选温度为15 ℃、矿浆pH为2、十二胺用量为300 g/t。在此条件下,进行了“一粗二精”的正浮选开路流程实验,获得了二水石膏（CaSO₄·2H₂O）质量分数为97.5%、二氧化硅质量分数为1.17%的精矿,所得精矿达到了GB/T 23456—2018《磷石膏》一级品指标的要求;二水石膏回收率为98.58%、二氧化硅去除率为92.23%。通过正浮选不仅成功实现了二水石膏和二氧化硅的有效分离,而且磷石膏中的水溶磷和水溶氟也得到了有效去除,从而提高了磷石膏的品质。     

HZSM5分子筛膜复合二氧化锡对甲烷的气敏性能研究

采用液相氧化法制备二氧化锡纳米颗粒,并利用浸渍法制备Pd负载二氧化锡纳米材料,通过丝网印刷得到气敏传感膜并在其表面印刷分子筛层。基于动态气敏测试系统探究传感器对甲烷气体的灵敏度及其在CO和乙醇干扰气体下的选择性。研究结果表明,在Pd-SnO₂敏感层表面印刷Pd-HZSM5层后,传感器对甲烷的响应能力显著提高,并且在体积分数为5×10^-4的CO存在时,对甲烷的选择性也得到明显的提升。同样,在质量分数为2×10^-5乙醇的存在下,传感器对甲烷的响应也没有受到干扰。通过对分子筛进行表征和催化分析,发现Pd-HZSM5对CO的催化效率可达100%,使得CO在扩散过程中被催化氧化,这可能是印刷Pd-HZSM5分子筛膜从而提高传感器选择性的主要原因。同时研究还表明,在敏感层表面印刷分子筛层并不会影响传感器的响应和恢复速率。     

陶瓷纳米颗粒在生物医学中的应用进展

近年来,纳米技术成为科学技术领域最重要与最激动人心的前沿领域之一.随着纳米技术的发展,纳米材料在生产和生活的各方面发挥着越来越重要的作用.陶瓷纳米颗粒作为一类重要的纳米材料,拥有体积效应、介电限域效应、量子尺寸效应和量子隧道效应等,使其在生物医学领域具有广阔的应用前景.本文综述了羟基磷灰石、磷酸钙、氧化铁、氧化锌和氧化铈陶瓷纳米颗粒的特点及其在肿瘤成像与治疗、骨组织工程和安全评价等生物医学领域的应用进展,并对陶瓷纳米颗粒在生物医学中的发展提出了几点建议.     

水泥回转窑系统新型锚固件的制作和应用

耐热钢锚固件是支撑热工设备耐火材料内衬的骨架,以增强耐火材料内衬抵抗静荷载、热应力、机械膨胀、机械振动,适用于所有干法生产线的浇注料施工,在高温窑炉中有广泛的应用。传统锚固件制作主要包括钢筋剪断、冲压、焊接、装套等工序,工序复杂且不满足现今环保要求,本文通过对新型炉窑锚固件的设计、生产和使用情况对比分析,新型锚固件完全可以替代传统锚固件,且提高了生产效率,实现了清洁生产和零排放。     

Effects of Ultrasonic Vibration on Material Flow and Thermal Cycles in Friction Stir Welding of Dissimilar Al/Mg Alloys

Comparative experiments are performed in friction stir welding (FSW) of dissimilar Al/Mg alloys with and without assistance of ultrasonic vibration. Metallographic characterization of the welds at transverse cross sections reveals that ultrasonic vibration induces differences in plastic material flow in two conditions. In FSW, the plastic material in the peripheral area of shoulder-affected zone (SAZ) tends to flow downward because of the weakening of the driving force of the shoulder, and a plastic material insulation layer is formed at the SAZ edge. When ultrasonic vibration is exerted, the stirred zone is divided into the inner and outer shear layers, the downward material flow trend of the inner shear layer disappears and tends to flow upward, and the onion-ring structure caused by the swirl motion is avoided in the pin-affected zone. By improving the flow behavior of plastic materials in the stirred zone, ultrasonic vibration reduces the heat generation, accelerates the heat dissipation in nugget zone and changes the thermal cycles, thus inhibiting the formation of intermetallic compound layers.

     

Mold-filling characteristics of AZ91 magnesium alloy in the low-pressure expendable pattern casting process

The magnesium (Mg) alloy low-pressure expendable pattern casting (EPC) process is a newly developed casting technique combining the advantages of both EPC and low-pressure casting. In this article, metal filling and the effect of the flow quantity of inert gas on the filling rate in the low-pressure EPC process are investigated. The results showed that the molten Mg alloy filled the mold cavity with a convex front laminar flow and the metal-filling rate increased significantly with increasing flow quantity when flow quantity was below a critical value. However, once the flow quantity exceeded a critical value, the filling rate increased slightly. The influence of the flow quantity of inert gas on melt-filling rate reveals that the mold fill is controlled by flow quantity for a lower filling rate, and, subsequently, controlled by the evaporation of polystyrene and the evaporation products for higher metal velocity. Meanwhile, the experimental results showed that the melt-filling rate significantly affected the flow profile, and the filling procedure for the Mg alloy in the low-pressure EPC process. A slower melt-filling rate could lead to misrun defects, whereas a higher filling rate results in folds, blisters, and porosity. The optimized filling rate with Mg alloy casting is 140 to 170 mm/s in low-pressure EPC.     

甲醇合成塔用 150 mm SA387Gr22C12 钢板组织和力学性能

对 150 mm 厚 SA387Gr22C12 钢板( / % : 0．13 ～0．14C,0．09Si,0．55 ～0．56Mn,0．004P,0．001S,2．48 ～2． 49Cr,1．11～1．12Mo) 模拟焊后拉伸性能、－29 ℃ 冲击性能、金相组织及回火脆化倾向评定等进行试验,并检测了交货态(正火 + 回火) 、最小模拟焊后态、最大模拟焊后态及步冷试验后的钢板各项性能指标 。结果表明,钢板的回火脆化 倾向不明显,其结果 CvTr55 + 2．5ΔCvTr55 为－63 ℃,完全满足甲醇合成塔用钢板的技术要求。