Unsteady free convection of second‐grade nanofluid with a new time‐space fractional heat conduction

The Caputo and Caputo–Fabrizio derivative are applied to study a second‐grade nanofluid over a vertical plate. A comparative analysis is presented to study the unsteady free convection of a second‐grade nanofluid with a new time–space fractional heat conduction. The governing equations with mixed time–space fractional derivatives are non‐dimensionalized and solved numerically, and a comparison between the Caputo and the Caputo–Fabrizio models is made. It is found that the temperature is higher for the Caputo–Fabrizio fractional model than the Caputo model, but the higher velocity only exists near the vertical plate for the Caputo–Fabrizio model than the Caputo model. Moreover, the velocity for the Caputo model will exceed the Caputo–Fabrizio model as y evolves.     

Transformation of the reabsorption characteristics of lignite treated by low and high temperature drying process

Abstract

The reabsorption characteristics of the lignite treated by low and high temperature drying process were addressed in the paper. The information about the moisture form, functional groups, effective water-filled porosities and equilibrium moisture content of the lignite before and after the drying process was investigated using Differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR) spectroscopy and a self-made reabsorption device, respectively. The results show that the low drying temperature (140, 190, 230?°C, 10?min, N₂) has little impact on the effective water-filled porosities of the resulted samples, whereas it has a great influence on the main oxygen-containing functional groups, which amount firstly decreases and then increases with the drying temperature increasing. In the case of the lignite samples dried under high-temperature (600, 700, 800?°C, 30?s, N₂), the amount of the effective water-filled porosity of the sample decreases and the amount of oxygen-containing functional groups increases as the temperature increasing. The reabsorption capability of the high temperature dried sample is much lower than that of the sample treated under low drying temperature. The reabsorption characteristics of the low-temperature dried samples are affected by the amount of the oxygen-containing functional groups, while the effective water-filled porosity is main factor for the lignite samples derived from high temperature drying process. Moreover, the work gives a good evidence that the high-temperature drying process is an effective choose for lignite upgrading.     

数据挖掘技术在软件系统中的应用

随着高新科学技术的发展,科学家研究出的利于人类工作生活的技术程序越来越多,大部分技术主要集中在如何帮助人们简化平时的工作量,能快速查找到自己所需要的信息,毕竟现代社会,工作效率和工作质量是关键。数据挖掘技术就具备这样的特点,数据挖掘技术在软件系统的应用将大大降低我们的工作量,提高我们的工作效率。现在我们研究数据挖掘技术在软件系统的应用,分析它是如何发挥其作用的,希望能提高使用该挖掘技术人员的使用效率。     

Model Selection for Unsupervised Learning of Visual Context

This study addresses the problem of choosing the most suitable probabilistic model selection criterion for unsupervised learning of visual context of a dynamic scene using mixture models. A rectified Bayesian Information Criterion (BICr) and a Completed Likelihood Akaike’s Information Criterion (CL-AIC) are formulated to estimate the optimal model order (complexity) for a given visual scene. Both criteria are designed to overcome poor model selection by existing popular criteria when the data sample size varies from small to large and the true mixture distribution kernel functions differ from the assumed ones. Extensive experiments on learning visual context for dynamic scene modelling are carried out to demonstrate the effectiveness of BICr and CL-AIC, compared to that of existing popular model selection criteria including BIC, AIC and Integrated Completed Likelihood (ICL). Our study suggests that for learning visual context using a mixture model, BICr is the most appropriate criterion given sparse data, while CL-AIC should be chosen given moderate or large data sample sizes.     

Improved homogenization of Ni in sintered steels through the use of Cr-containing prealloyed powders

The homogenization of Ni in powder metal (PM) steel compacts is usually difficult even after high-temperature sintering at 1250°C. An earlier study by the authors demonstrated that this problem can be alleviated through the addition of 0.5 wt pct Cr in the form of stainless steel powders. To further improve the microstructure and mechanical properties of Ni-containing PM steels and to understand the mechanisms, an attempt was made in this study using the Fe-3Cr-0.5Mo prealloyed powder as the base material. The results showed that the distribution of the Ni additives was significantly improved. As a result, the tensile strength of the Fe-3Cr-0.5Mo-4Ni-0.5C compact sintered at 1250°C reached 1323 MPa. The elongation was higher than 1 pct. These sinter-hardened properties, which were attained using a slow furnace cooling rate, were comparable to those of the sinter-hardened alloys reported in the literature using accelerated cooling and were equivalent to those of the best quenched-and-tempered alloys registered in the Metal Powder Industries Federation (MPIF) standards. These improvements were attributed to the positive effect of Cr addition on alloy homogenization due to the reduction of the repelling effect between Ni and C, as was demonstrated through the thermodynamic analysis using the Thermo-Calc program.     

差分跳频通信系统的特点及性能

文章介绍了一种新型的短波跳频通信技术——差分跳频,分析了差分跳频技术区别于常规跳频技术的主要特点。针对按序列检测的信号接收方法,对差分跳频通信系统在AWGN信道下的性能进行了理论分析,同时做出相应的计算机仿真,证实了差分跳频通信技术和按序列检测方法的结合,使通信系统在AWGN信道下的性能得到了比较显著的提升。     

Effective Location Based Services with Dynamic Data Management in Mobile Environments

With the proliferation of mobile computing technologies, location based services have been identified as one of the most promising target application. We classify mobile information service domains based on feature characteristics of the information sources and different patterns of mobile information access. By carefully examining the service requirements, we identify the dynamic data management problem that must be addressed for effective location based services in mobile environments. We then devise a general architecture and cost model for servicing both location independent and location dependent data. Based on the architecture and cost model, we propose a set of dynamic data management strategies that employs judicious caching, proactive server pushing and neighborhood replication to reduce service cost and improve response time under changing user mobility and access patterns. Detail behavior analysis helps us in precisely capturing when and how to apply these strategies. Simulation results suggest that different strategies are effective for different types of data in response to different patterns of movement and information access. Shiow-yang Wu is an associate professor of the Department of Computer Science and Information Engineering at National Dong Hwa University, Hualien, Taiwan, R.O.C. He received the BS and MS degrees in computer engineering from National Chiao Tung University, Hsinchu, Taiwan, ROC, and the PhD degree in computer science from the University of Texas at Austin in 1984, 1986, and 1995, respectively. His research interests include data/knowledge bases, mobile computing, distributed processing, intelligence information systems, and electronic commerce. Kun-Ta Wu was born in Taipei, Taiwan, R.O.C., in 1976. He received the B.S. degree in computer science from Soochow University, Taipei, Taiwan, R.O.C., in 1999 and the M.S. degree in computer science and information engineering from National Dong Hwa University, Hualien, Taiwan, R.O.C., in 2001. Currently, he is an Assistant Researcher in the Domestic Division at Science and Technology Information Center, National Science Council, R.O.C., as a member of Information Gathering and Analysis Group of National Information and Communication Security Taskforce. His research interests include mobile computing, wireless network and information security.     

Na+、K+离子交换对Co-Mo/MCM-41加氢脱硫催化剂的影响

 用偏硅酸钠和正硅酸乙酯作硅源制备了MCM-41（分别记作MCM-41(S)和MCM-41(T)）分子筛，并用Na₂C₂O₄和K₂C₂O₄对MCM-41(S)进行了碱金属离子交换改性。以质量分数0.8 %的二苯并噻吩（DBT）的十氢萘溶液为模型化合物，考察了不同MCM-41担载的Co-Mo硫化物催化剂对DBT的加氢脱硫反应性能。结果表明，MCM-41担载的Co-Mo催化剂加氢活性较低，DBT主要通过直接脱硫反应路径脱硫。其活性顺序为：Co-Mo/MCM-41(T)>Co-Mo/MCM-41(S)>Co-Mo/MCM-41(K)>Co-Mo/MCM-41(Na)。UV-Vis结果表明，部分Co与MCM-41(S)中少量Al发生相互作用，生成了CoAl₂O₄，是造成Co-Mo/MCM-41(S)活性降低的重要因素。而在Co-Mo/MCM-41(K)和Co-Mo/MCM-41(Na)中，除CoAl₂O₄物种之外，碱金属的引入还促进了Co₃O₄物种的形成，使其活性进一步降低。     

国有科研单位人才流失原因分析及对策

近年来,国有科研单位,尤其是地处经济不发达地区的国有科研单位,出现了较为严重的人才流失现象,一定程度上影响和制约了国有科研单位的发展。通过对国有科研单位人才流失原因的分析,提出了相应的对策。