无底柱分段崩落法采矿进路受力过程分析

在使用无底柱分段崩落法的矿山,大都存在着地压现象。其主要表现是采矿进路和联络道的变形破坏。对采矿进路在开挖和回采过程中各阶段受力情况的分析表明,进路的变形、破坏主要是受到岩体初始静应力、爆破动应力和矿柱支撑应力的综合作用的结果。     

螺带式搅拌器在假塑液中的混合及放大的研究

本文综合研究了螺带式搅拌器在假塑性液体中的混合特性及动力特性，测定了双螺带，内外螺带及螺带螺旋３种类型搅拌器的功率常数Ｋｐ和Ｍｅｔａｎｅｒ常数Ｋｓ，并得出混匀操作和传质工艺过程的放大准则。     

一缩二乙二醇二缩水甘油醚的合成

以一缩二乙二醇和环氧氯丙烷为原料、三氟化硼乙醚络合物为催化剂合成一缩二乙二醇二缩水甘油醚(DGEG)。讨论了催化剂用量、原料配比、碱金属氢氧化物以及成环反应温度对产物收率的影响。同时 ,用傅立叶红外光谱对其进行了分析与表征。当三氟化硼乙醚络合物用量为 3份、环氧氯丙烷与一缩二乙二醇的物质的量比为 8∶1、用氢氧化钾在 30℃左右进行成环反应时 ,可以得到低粘度、高收率的产物。     

炭黑品种及用量对NBR/CHR并用胶性能的影响

研究了炭黑Ｎ６６０、Ｎ６３０、Ｎ７６２、天然气半补强炭黑及喷雾炭黑对ＮＢＲ／均聚氯醚橡胶（ＣＨＲ）并用胶性能的影响。试验结果表明，这些炭黑在ＮＢＲ／ＣＨＲ并用胶中的用量达到８０份时，并用胶的加工性能仍较好。随着炭黑用量的增大，ＮＢＲ／ＣＨＲ并用胶的耐四氯化碳性能提高；压缩永久变形、压缩温升及硬度增大；扯断伸长率和回弹值下降；而拉伸强度则是先升高，当炭黑用量达到６０份时即下降；撕裂强度也是先升高，而后在不同用量处出现下降趋势。     

Demineralization of a UK bituminous coal using HF and ferric ions

A UK bituminous coal has been used to study demineralization by two-stage chemical leaching. The first-stage uses hydrofluoric acid (HF) at 65 °C and reduces the ash content from 5.30 wt% to 1.37 wt% by mainly removing Al and Si containing minerals. Subsequent leaching by ferric ions decreases the ash content further to 990 ppm by removing most of the pyrite and fluorides formed during the HF leaching. Calorific value of the coal shows no change following leaching, which suggests no oxidation is occurring to the coal carbonaceous matrix. The mercury and sulfur contents after the two-stage leaching sequence decrease by 40% and 26%, respectively.     

Ozone-Based Advanced Oxidation Processes for the Decomposition of N-Methyl-2-Pyrolidone in Aqueous Medium

The present study investigates the decomposition of N-Methyl-2-Pyrolidone (NMP) using conventional ozonation (O₃), ozonation in the presence of UV light (UV/O₃), hydrogen peroxide (O₃/H₂O₂), and UV/H₂O₂ processes under various experimental conditions. The influence of solution pH, ozone gas flow dosage, and H₂O₂ dosage on the degradation of NMP was studied. All ozone-based advanced oxidation processes (AOPs) were efficient in alkaline medium, whereas the UV/H₂O₂ process was efficient in acidic medium. Increasing ozone gas flow dosage would accelerate the degradation of NMP up to certain level beyond which no positive effect was observed in ozonation as well as UV light enhanced ozonation processes. Hydrogen peroxide dosage strongly influenced the degradation of NMP and a hydrogen peroxide dosage of 0.75 g/L and 0.5 g/L was found to be the optimum dosage in UV/H₂O₂ and O₃/H₂O₂ processes, respectively. The UV/O₃ process was most efficient in TOC removal. Overall it can be concluded that ozonation and ozone-based AOPs are promising processes for an efficient removal of NMP in wastewater.     

Spherical NiO-C composite for anode material of lithium ion batteries

Spherical NiO-C composite was prepared by dispersing spherical NiO in glucose solution and subsequent carbonization under hydrothermal conditions at 180 °C. The microstructure and morphology of the NiO-C and NiO powders were characterized by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrochemical properties of the electrodes were measured by galvanostatic charge-discharge tests, cyclic voltammetric analysis (CV), and electrochemical impedance spectroscopy (EIS). SEM images showed that the amorphous carbon not only coated on the surface but also filled the inner pores of the NiO spheres. Electrochemical tests showed that the NiO-C composite exhibited higher initial coulombic efficiency (66.6%) than NiO (56.4%), and better cycling performances. The improvement of these properties is attributed to the carbon, as it can reduce the specific surface area of porous sphere, and enhance the conductivity of porous NiO.     

Ultrasonic oscillations effect on rheological and processing properties of metallocene‐catalyzed linear low density polyethylene

The effects of ultrasonic oscillations and die materials on die pressure, productivity of extrusion, melt viscosity of metallocene‐catalyzed linear low density polyethylene (mLLDPE), as well as their mechanism were studied in a special ultrasonic oscillations extrusion system developed in our lab. Die materials used in our experiment included steel, brass, and polytetrafluoroethylene (PTFE)_. The experimental results showed that ultrasonic oscillations as well as die materials have great influence on the rheological and processing behavior of mLLDPE. Ultrasonic oscillations can greatly increase the productivity of mLLDPE melt extruded through different dies, and can decrease the die pressure and the melt viscosity of mLLDPE. Compared with steel or brass die, mLLDPE melt extruded through PTFE die is more sensitive to ultrasonic oscillations. A possible mechanism for the improved processability of mLLDPE is proposed in this article. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1873–1878, 2003     

基于蜜罐技术的主动防护网络入侵探究

随着信息技术的快速发展,网络安全问题日益突出,如何保护网络安全成为人们研究的重点.在实际工作过程中应用蜜罐技术来进行主动防护网络入侵是一种新方式.由蜜罐技术和分布式代理构成的防护体系,能够有效降低攻击检测误报率.网络安全形势日益复杂的背景下加强对蜜罐技术的研究具有重要意义.本文将重点探讨如何利用蜜罐技术来实现对网络入侵的主动防护.     

XRF法在聚乙烯微量金属分析中的应用

探讨了用Ｘ射线荧光光谱分析法（ＸＲＦ法）测定聚乙烯中所含的微量金属Ｆｅ、Ｔｉ、Ａｌ的方法，简 分析条件及实验方法。