Ionothermal synthesis of a three-dimensional zinc phosphate with DFT topology using unstable deep-eutectic solvent as template-delivery agent

A three-dimensional zinc phosphate compound with DFT topology, designated as ZnPO₄-EU1, has been synthesized by an ionothermal approach from the system HF-ZnO–P₂O₅-choline chloride-imidazolidone. Ethylenediamine, derived from decomposition of the imidazolidone component of the deep-eutectic solvent (DES) itself, is delivered to the synthesis and serves as an appropriate template for ZnPO₄-EU1. Experiments in which the synthesis conditions were varied showed that ZnPO₄-EU1 may be prepared over a wide molar ratio of P/Zn = 0.55–13.0. Powder X-ray diffraction patterns have been obtained at intervals to track the crystallization process of this material. The experimental data show that Zn₃(PO₄)₂ · 4H₂O (a dense phase) was first isolated from the DES after reaction for 1 h. Subsequently, the pure phase of ZnPO₄-EU1 was obtained with increasing crystallization time from 12 h to 72 h. The experimental results show that the nucleation and crystallization take place with relatively low levels of solvent degradation, demonstrating that zinc phosphate with a three-dimensional framework can be synthesized by in situ generation of an appropriate template using an unstable DES at high temperatures (150–200 °C).     

IF钢冷轧及再结晶初期微观组织的TEM研究

采用透射电子显微镜对不同压下量和再结晶初期的IF钢样品进行了研究．结果表明：无论是在较小形变量下还是在较大形变量下，形变不均匀性是普遍存在的；冷变形程度不同，织构组分不同，TEM形貌也不同；在再结晶的最初期，冷轧的形变组织演变为近乎等轴的亚晶，优先形成{111}〈uvw〉取向的晶核，晶核逐渐吞并周围的形变基体而长大，最终形成再结晶γ-纤维织构．     

Preparation of CeO2-ZrO2 mixed oxide with high surface area and high thermal stability

Ceria-zirconia solid particles have been recognized as a key material of the automotive exhaust catalysts since they can release and uptake oxygen owing to the rapid reversible oxidation states of cerium between Ce³⁺ and Ce⁴⁺. Several methods have recently been described to prepare the CeO₂-ZrO₂ solid particles used in the catalysts. In this paper, a new coprecipitation method is used to prepare the CeO₂-ZrO₂ solid particles. The Ce-Zr alcogel is dried and calcined in flowing N₂ not in flowing air under atmospheric pressure. The results show that the ceria-zirconia sample calcined at 650 °C has high surface area over 90 m²g⁻¹, which drops to 40 m²g⁻¹ following treatment at 900°C.     

分置式牛津型斯特林制冷机的数值分析与实验验证

对分置式牛津型斯特林制冷机进行了数值计算 ,介绍了计算模型考虑到的众多不可逆因素。通过对计算结果与实验结果的对比 ,验证了本文数值计算的准确性 ,说明本文计算模型与数值处理方法是切实可行的     

Electrochemical C-V Characteristics and Photoluminescence of a-C∶N Films

Amorphous carbon (a-C) films and amorphous carbon films incorporating with the nitrogen (a-C∶N) were deposited on silicon substrates in a radio-frequency driven plasma enhanced chemical vapour deposition system, while the surface electrical properties of films were investigated by electrochemical capacitance-voltage measurements. It was examined the effect of the interface defects on the properties and deduced that the conducting type of a-C∶N films was n-type. Subsequently, a comparative studies of a-C and a-C∶N films were performed by photoluminescence spectra depending on the temperature. With the decrease of the temperature, the main band with peak energy of 2.48 eV in the a-C∶N films was more intense compared with the other three bands caused by amorphous C in the a-C films.     

石化企业分配制度改革初探

在明确中国石化集团公司收入分配制度改革的目标模式下,从健全和完善企业激励机制的角度,对炼化企业职工收入分配制度中工资和奖金的分配设计提出改进措施和建议。     

就地补偿在动力厂水泵电机上的应用实例

就我公司动力厂给水车间155kW水泵电机无功就地补偿的可行性及经济效益进行了分析和研究，对工厂用电如何节能降耗有一定的参考价值。     

电接点压力表补水泵定压系统的应用

阐述了电接点压力表补水泵定压系统的一些应用问题 ,给出了电接点压力表定压点的上、下限计算公式 ,并提出了该系统补给水泵、补给水箱及安全阀的设计选型方法     

智能工作站主机的MMPIS实验模型研究──一个全互连式结构MMPIS硬件环境的设计与实现

本文介绍中日国际合作开发研究的Ａ１型智能网（Ａ１型ＩＮ）智能工作站（ＩＷ）主机的并行推理硬件结构的实验模型设计与实现，给出了一种并行推理硬件支持环境实现方案和该方案在实现中若干问题的解决方法。     

OSI参考模型与B—ISDN协议参考模型的比较

分析了ＯＳＩ参考模型和Ｂ－ＩＳＤＮ协议参考模型之间的关系，为Ｂ－ＩＳＤＮ与以ＯＳＩ为标准的数据网的互联打下了基础。