MIMO系统中简单的扩展空时块编码分集技术研究

本文提出一种多输入多输出（MIMO）天线系统中简单的扩展空时块编码（SSTBC）分集技术，采用沃尔什码来区分各天线发送数据子流。采用这种方法，在系统带宽一定时，不降低发送信息速率，同时接收机简单。不同天线的发送信息经过了所有收一发天线对之间的空间子信道，获得了所有路径的部分空间分集增益，仿真结果表明，这种增益的获得不受限于接收分集阶数，并且随发射天线的增加以一定的线性关系增加。     

绍兴市城区河道整治工程若干问题初探

通过对绍兴城区环城河、大环河、古运河、古城河等河道整治工程内容和整治成效的分析，总结了绍兴城区河道整治的5大特点，针对河道建设中存在的有关问题，提出了今后城市河道整治的4条具体措施。     

Effect of boron on the low-cycle fatigue behavior and deformation structure of INCONEL 718 at 650 °C

Symmetrical push-pull low-cycle fatigue (LCF) tests were performed on INCONEL 718 (IN718) containing 12, 29, 60, and 100 ppm B at 650 °C. The results showed that all the alloys experienced a relatively short period of initial cyclic hardening at low strain amplitudes, followed by a regime of saturation or slightly continuous cyclic softening. The initial cyclic hardening phase decreased with increasing strain amplitudes, and disappeared at the high strain amplitudes. A serrated flow was observed in the plastic regions of cyclic stress-strain hysteresis loops. The saturated cyclic stress amplitude at a given strain amplitude was highest for the alloy with 60 ppm B, and lowest for the alloy with 12 ppm B. The LCF lifetime increased with increasing B concentration up to 60 ppm, and then decreased as the B content increased from 60 to 100 ppm. Fractographic analysis suggested that the fracture mode changed from intergranular to transgranular cracking as the B concentration increased. The characteristic deformation microstructures produced by LCF tests at 650 °C, examined via transmission electron microscopy, were regularly spaced arrays of planar deformation bands on {111} slip planes in all four alloys. A ladderlike structure was observed in some local regions in the alloy with 12 ppm B. Heavily deformed planar deformation bands were observed in the fatigued specimens with 100 ppm B. The mechanism of improvement in the LCF life of IN718 due to B addition is discussed.     

情境故事法在产品设计开发中的应用

从产品设计中"以使用者为中心"的设计要求出发,引入情境故事法的相关内容.详细论述了情境故事法的概念、流程、操作方法,并以商务笔记本为研究载体,对商务笔记本的典型用户的使用特性,以及使用过程中的最初情境和遇到的问题进行综合分析.站在用户的角度建立情境故事以寻求商务笔记本设计的创新点,从而得到新的故事方案.最后对情境故事法使用的局限性作了些简要评述.     

SU-8 3D microoptic components fabricated by inclined UV lithography in water

Out-of-plane microlenses and microoptical fiber holder are two of the most important components for building an integrated microoptic system with a precise alignment accuracy. In this paper, a simple and convenient method to fabricate these components from SU-8 by using inclined UV lithography in water is proposed. It consists of two perpendicular exposures in SU-8 at ±45°. DI water possesses a low absorption coefficient and a moderate and stable value of refractive index in near UV. Using water, the exposure angle in SU-8 can be increased to 50° from 35° in air necessary to pattern the desired 45° slope of the sidewalls. The principle of the proposed technique and the detailed fabrication process of the microoptic components will be presented. The integratability of the fabricated components was demonstrated by the fabrication of the microoptical fiber holder with a pre-aligned out-of-plane microlens.     

Characteristics of Milk Powders Produced by Spray Freeze Drying

Skim and whole milk powders were manufactured at lab scale by spray freeze drying (SFD), using liquid nitrogen as the cryogen. The polydispersity of droplet/particle sizes was limited using an encapsulator nozzle to atomize the feed. Particle morphology was examined using a scanning electron microscope. Samples were compared with equivalent spray-dried powders in tests of wettability and dissolution in water. The spray freeze-dried powders were found to be highly porous, with a uniform structure of pores throughout the entire particles. When tested in water, SFD skim milk powders wetted roughly three times as fast as industrially spray-dried agglomerated skim milk powders and were observed to dissolve rapidly by breaking down into smaller particles.     

状如琼，凝为脂

在我们喝的饮料粒粒橙中，为什么那些细小的橙子颗粒是悬浮在橙汁中的呢？果冻和布丁为什么是透明，且柔软有弹性的呢？去看看成分表，我们不难发现共同之处，看似不同的食品都添加了一种共同的成分——琼脂。[编者按]     

Ring‐opening polymerization of D,L‐lactide by rare earth 2,6‐dimethylaryloxide

Ring‐opening polymerization of D,L ‐lactide (LA) has been successfully carried out by using rare earth 2,6‐dimethylaryloxide (Ln(ODMP)₃) as single component catalyst or initiator for the first time. The effects of different rare earth elements, solvents, monomers and catalyst concentration as well as polymerization temperature and time on the polymerization were investigated. The results show that La(ODMP)₃ exhibits higher activity to prepare poly(D,L ‐lactide) (PLA) with a viscosity molecular weight of 4.5 × 10⁴ g mol^?1 and the conversion of 97 % at 100 °C in 45 min. The catalytic activity of Ln(ODMP)₃ has following sequence: La > Nd > Sm > Gd > Er > Y. A kinetic study has indicated that the polymerization is first order with respect to both monomer and catalyst concentration. The apparent activation energy of the polymerization of LA with La(ODMP)₃ is 69.6 kJ mol^?1. The analyses of polymer ends indicate that the LA polymerization proceeds according to ‘coordination–insertion’ mechanism with selective cleavage of the acyl–oxygen bond of the monomer. Copyright © 2004 Society of Chemical Industry