Formation and Characterization of 1.5-Monolayer Self-Assembled InAs/GaAs Quantum Dots Using Postgrowth Annealing

In this paper, we report that low-density InAs/GaAs quantum dots (QDs) can be formed by postgrowth annealing the samples with 1.5-monolayer (ML) InAs coverage, which is thinner than the critical layer thickness for the Stranski-Krastanov growth. The annealing procedure was performed immediately after the deposition of the InAs layer. The effects of annealing time and annealing temperature on the dot density, dot size, and optical characteristics of the QDs were investigated. The optimum annealing conditions to obtain low-density QDs are longer than 60 s and higher than 500degC . Meanwhile, no luminescence can be observed for the wetting-layer, which may suggest that the postgrowth annealing will make the wetting layer thinner and thus reduce the effects of wetting layer on carrier relaxation and recombination. On the other hand, we observe that a decrease of the PL intensity at the annealing conditions of 60 s and 515degC , which is possibly due to the increasing surface dislocations resulted from the In adatom desorption at higher annealing temperature.     

An Area Optimization Method for Digital Filter Design

In this paper, we propose an efficient design method for area optimization in a digital filter. The conventional methods to reduce the number of adders in a filter have the problem of a long critical path delay caused by the deep logic depth of the filter due to adder sharing. Furthermore, there is such a disadvantage that they use the transposed direct form (TDF) filter which needs more registers than those of the direct form (DF) filter. In this paper, we present a hybrid structure of a TDF and DF based on the flattened coefficients method so that it can reduce the number of flip‐flops and full‐adders without additional critical path delay. We also propose a resource sharing method and sharing‐pattern searching algorithm to reduce the number of adders without deepening the logic depth. Simulation results show that the proposed structure can save the number of adders and registers by 22 and 26%, respectively, compared to the best one used in the past.     

Novel algorithms for shared segment protection

The major challenges in designing survivable schemes are how to allocate a minimal amount of spare resources (e.g., bandwidth) using fast (e.g., polynomial-time) algorithms, and, in case a failure occurs, to be able to recover quickly from it. All existing approaches invariably make tradeoffs. We propose novel shared segment protection algorithms which make little or no compromise . We develop an elegant integer linear programming (ILP) model to determine an optimal set of segments to protect a given active path. Although the ILP approach is useful for a medium-size network, it is too time consuming for large networks. Accordingly, we also design a fast heuristic algorithm based on dynamic programming to obtain a near-optimal set of segments. Although the heuristic algorithm has a polynomial time complexity, it can achieve a bandwidth efficiency as high as some best-performing shared path protection schemes and, at the same time, much faster recovery than these shared path protection schemes. The proposed scheme is also applicable to a wide range of networking technologies, including Internet Protocol and wavelength-division multiplexing networks under the generalized multiprotocol label switched framework.     

Achieving fast and bandwidth-efficient shared-path protection

Dynamic provisioning of restorable bandwidth guaranteed paths is a challenge in the design of broad-band transport networks, especially next-generation optical networks. A common approach is called (failure-independent) path protection, whereby for every mission-critical active path to be established, a link (or node) disjoint backup path (BP) is also established. To optimize network resource utilization, shared path protection should be adopted, which often allows a new BP to share the bandwidth allocated to some existing BPs. However, it usually leads the backup paths to use too many links, with zero cost in term of additional backup bandwidth, along its route. It will violate the restoration time guarantee. In this paper, we propose novel integer linear programming (ILP) formulations by introducing two parameters (/spl epsi/ and /spl mu/) in both the sharing with complete information (SCI) scheme and the distributed partial information management (DPIM) scheme. Our results show that the proposed ILP formulations can not only improve the network resource utilization effectively, but also keep the BPs as short as possible.     

塔里木山前复杂地层钻头使用技术

利用测井资料结合实测的岩石力学性质、邻井的岩性剖面建立了岩石力学参数模型,综合解释了单井岩石在纵向剖面上的力学性质。借鉴邻井钻头使用情况,以推广高效PDC钻头为主,介绍了山前构造钻头选型情况。针对山前构造的地层岩性特征,从复合片、刀翼形状、齿型、切削齿力平衡等方面设计和改进了PDC钻头。改进后的钻头使塔里木山前复杂地层钻头使用获得了突破性进展。     

Lipase‐catalyzed dynamic kinetic resolution of (R,S)‐fenoprofen thioester in isooctane

A lipase‐catalyzed enantioselective hydrolysis process under in situ racemization of the remaining (R)‐thioetser substrate with trioctylamine as the catalyst was developed for the production of (S)‐fenoprofen from (R,S)‐fenoprofen 2,2,2‐trifluoroethyl thioester in isooctane. Detailed investigations of trioctylamine concentration on the enzyme activation and the kinetic behavior of the thioester in racemization and enzymatic reactions were conducted, in which good agreement between the experimental data and theoretical results was observed. © 2002 Society of Chemical Industry     

Rheology in Processing of in Situ Composites of Polypropylene and Low Melting Poing Metals

The low melting point metallic tin powder or alloy of tin and lead was blended with polypropy-lene. A kind of in situ composite has been prepared. The variations of torque were studied when the composites were mixed in Haake torque rheogeniometer. By way of capillary extrusion, effects upon rheology of the in situ com-posites of the low melting point metals (LMPM) and coupling agent for their different variety and content, were investigated. From flow curves, the results indicate that in situ composites mixed with the LMPM are a kind of pseudoplastic fluid. If the LMPM were melted, the higher the content of the LMPM , the lower apparent viscosity of composites. Meanwhile, when the coupling agent is added into composites, the viscosity of composite will go up first and drop then. This shows that the LMPM have a promoter flow action on the polypropylene.     

分形方法用于有噪图像边缘检测的研究

本文研究了加性高斯白噪声对于基于离散分数布朗随机场模型图像分形维数估计的影响，并将分形方法用于图像边缘检测，指出在加性高斯白噪声的情况下，分形方法用于图像边缘检测较之经典的基于梯度运算的边缘检测方法有好的抗噪性能，同时又能检测比较丰富的图像边缘细节。     

椭球反射镜膜厚均匀性

本文分析了椭球反射镜膜层厚度均匀性对反射率的影响,从理论上得到膜厚计算公式。根据计算的膜厚分布设计了遮蔽板,获得较好的反射特性。