扩链剂在PVC树脂生产中的应用

讨论了常见扩链剂的功能及在聚氯乙烯树脂生产中的应用。     

异丁烯两段催化氧化制甲基丙烯酸催化剂研究 Ⅰ．异丁烯气相氧化制甲基丙烯醛多元复合氧化物催化剂的研究

本文报导用于异丁烯（叔丁醇）选择氧化制ＭＡＬ（甲基丙烯醛）的多元复合氧化物催化剂的研究结果。同共沉淀法制备的催化剂的活性主要决定于其化学组成，同时受到制备条件的影响。最佳催化剂的主要物相组成为ＰｂＯ３，Ｂｉ２ＭｏＯ３．３、ＮｉＭｏＯ４、Ｓｂ２Ｏ３及ａ－Ｆｅ２Ｏ３小颗粒。在３５５℃，１０００～２５００ｈ－１空速范围，叔丁醇：水：空气＝１：３．３：７（摩尔比）的条件下可获得异丁烯转化率达９６％，ＭＡＬ选择性达８９％的结果。     

Water-soluble and amphiphilic polymers

Summary Three PEO-PSt-PEO triblock polymers and their parent ho-nopolystyrene have been studied by means of light scattering technique in chloroform, toluene and ethyl acetate. It has been found that the weight average molecular weights calculated by using the equation Mapp- were unbelievable negative values; and the largest deviation appeared for the sample with PEO mole content of about 50%. Data of PSt-PEO-PSt triblock polymers in literature have been quoted and discussed.     

中央空调的水处理

本文扼要介绍了中央空调循环冷却水和冷冻水系统中常见的问题及其原因,并对冷却水和冷冻水的处理程序作了初步的阐述.     

ATO包裹硅酸锆的制备与应用

采用化学共沉淀技术制备了锑掺杂二氧化锡(ATO)包裹硅酸锆的导电粉体,对比了该导电粉体与ATO在防静电陶瓷中的应用效果。结果表明与掺纯ATO相比较,掺入ATO包裹硅酸锆的防静电陶瓷颜色比较浅,并且能明显减少氧化锡的用量,当陶瓷的表面电阻为107Ω/□量级时,用ATO包裹硅酸锆作为导电填料可以节省25%左右的ATO。     

The determination of the pore structural parameters of isoporous resins by inverse GPC

The swollen pore structure of a series of microporous isoporous resins (7.4–140 Å) are investigated with inverse GPC, n-alkylbenzenes and linear polystyrenes being used as probe molecules. The results indicated that, with the lowering of crosslinking degree of isoporous resins, the average pore diameter increased and the pore distribution curve broadened. All pore volume distribution obeyed a log-normal distribution. Based on the linear regression method, the experimental data were fitted to a monotonously declining exponential function and a normal distribution function by a computer, and some important structural parameters such as average pore diameter, pore volume distribution, specific surface area, etc. were obtained. The specific surface area of swollen gels were found much greater than those in the dry state measured by N₂ adsorption.     

冷却器盘管失效分析及防范措施

本文介绍了冷却器盘管破裂泄漏的情况，分析了失效破坏的原因，并提出防止冷却器盘管破裂泄漏的措施。     

Electrochemical performance of nanocrystalline Li3V2(PO4)3/carbon composite material synthesized by a novel sol–gel method

A novel sol–gel method based on V₂O₅·nH₂O hydro-gel was developed to synthesize nanocrystalline Li₃V₂(PO₄)₃/carbon composite material. In this route, V₂O₅·nH₂O hydro-gel, NH₄H₂PO₄, Li₂CO₃ and high-surface-area carbon were used as starting materials to prepare precursor, and the Li₃V₂(PO₄)₃/carbon was obtained by sintering precursor at 750 °C for 4 h in flowing argon. The sol–gel synthesis ensures homogeneity of the precursors and improved reactivity. The sample was characterized by XRD, SEM and TEM. X-ray diffraction results show Li₃V₂(PO₄)₃ sample is monoclinic structure with the space group of P2₁/n. The TEM image indicates that the Li₃V₂(PO₄)₃ particles modified by conductive carbon are about 70 nm in diameter. The Li₃V₂(PO₄)₃/carbon system showed that the discharge capacities in the first and 50th cycle are about 155.3 and 143.6 mAh/g, respectively, in the range of 3.0–4.8 V. The sol–gel method is fit for the preparation of Li₃V₂(PO₄)₃/carbon composite material which may offer some favorable properties for commercial application.     

Morphologies and microstructures of tree-like carbon produced at different reaction conditions in a CVD process

Centimeter-size multi-branched tree-like carbon structures have been generated by the catalytic chemical vapor deposition of toluene using ferrocene as the catalyst precursor and investigated by means of SEM, TEM, and EDX. It is found that a temperature of 1000-1200 °C and a carrier gas flow rate of 1000-2500 ml/min are necessary for the generation of the carbon trees. Their morphologies and microstructures change greatly with the changing reaction conditions. The fractal dimensions of the trees are calculated to quantitatively investigate the influence of different reaction temperatures on the morphologies.     

Phase Assemblages of Pr α-sialon Derived from SHS-ed Powders and TEM Study on the Nucleation of Pr α-sialon

The Pr α-sialon powders prepared by self-propagating high-temperature synthesis (SHS), consisting of 55 wt% Pr α-sialon and 45 wt% of β-sialon (abbreviated as α' and β'), were hot-pressed at 1800°C for 1 h. The results showed that Pr α' phase would transfer to β' with the appearance of JEM phase (Pr(Si_{6− z} Al _z )(N_{10− z} O _z )) after sintering, thus resulting in the increase of β' phase to 86 wt%. The addition of Y₂O₃ into SHS-ed Pr α' powders as the starting materials restrains the transformation of α' to β' and prevents the formation of JEM phase as well. The nucleation mechanism of Pr α' grain during hot-pressing was investigated in terms of transmission electron microscope and energy-dispersive spectrometer analysis. Two nucleation modes of Pr α' grains were found, i.e., nucleating on the undissolved Pr α' grains and on the nuclei of (Pr, Y) α' grains precipitated from liquid phase.