直接氯化法合成对硝基氯化苄

介绍了以对硝基甲苯和氯气为原料 ,在催化剂存在下合成对硝基氯化苄的方法 ,考察了催化剂种类、反应温度、溶剂配比等因素对反应的影响 ,优化的反应条件为 :对硝基甲苯用量 1 3 7g,对硝基甲苯 /邻二氯苯 (摩尔比 ) =1∶ 0 .6,w (偶氮二异丁腈 ) =0 .6% ,反应时间 3 h,反应温度 1 60℃ ,产物单程收率大于 65 % ;将反应混合物中未反应的原料分离后 ,以无水乙醇为溶剂结晶纯化 ,物料 /溶剂 (摩尔比 ) =1∶ 1 .5时晶体含量在 99.0 %以上 ,结晶收率达 67     

Cif2000平台下的核磁共振测井解谱方法研究

介绍了在Cif2000多井解释平台下的核磁共振解谱方法与编程实现。解谱采用加入平滑因子后在特征矩阵的奇异值分解中截去小的非零奇异值的方法，可以在低信噪比时得到稳定的弛豫谱，在油田实际应用中证明了该方法的有效性。根据该方法在Cif2000平台上编制了完整的解谱处理程序，可以直接用于油田的生产实际。     

模糊数学识别火山岩岩性

针对火岩地层岩性识别成功率低的状况，应用模糊数学原理，建立模糊数学识别火山岩岩性模式，识别和划分火山岩地层岩性，以便进一步深入研究火山岩油气藏储层，选择8个反映火山岩岩性测井参数，确定阈值；利用所建立的火山岩岩性识别模式，对火山岩岩性进行分类；依据最大隶属原则，识别火山岩岩性，应用实地研究资料，识别10种火山岩岩性，并与岩心鉴定统计分析结果对比，一致性达85％。表明该方法识别火山岩岩性精度较高，在地质上具有很好的应用前景。     

第三代短波自动链路建立系统特性分析及仿真实现

分析了第三代短波自动链路建立系统的工作特性及技术特点，并对系统仿真实现的原则及一些细节问题进行了较深入的探讨，同时对仿真实现中涉及的链路质量分析（LQA）算法进行了研究。     

Improvement of RCA transistor using RTA annealing after theformation of interfacial oxide

A polysilicon emitter RCA transistor (an ultra-thin interfacial oxide layer exists between polysilicon and silicon emitter) is presented which can operate at 77 K for the first time. An ultra-thin (1.5 nm) interfacial oxide layer is grown deliberately between polysilicon and silicon emitter using RCA oxidation and excellent device stability is obtained after rapid thermal annealing (RTA) treatment in nitrogen atmosphere. The RCA transistor exhibits good electrical performance at very low temperature for an emitter area of 3 × 8 μm². The maximum toggle frequency of a 1:2 static divider is 1.2 GHz and 732 MHz at 300 K and 77 K, respectively     

减压渣油与FCC油浆共炭化的化学组成变化

考察了齐鲁石化胜利炼油厂催化油浆（FCC）和胜利减压渣油（VR）在490℃，0.8MPa下不同混合比的原料和不同反应时间的中间产物的HS、TS、PS、P及其1h中间产物的HS和TS的^1H-NMR。数据结果反映了体系的反应速度。掺入FCC油浆抑制了VR的反应活性，降低了体系的反应速度，增加了基质的溶解度；1h中间产物的组成结构更接近于原料及反应体系的反应性和基质的溶解度；1h中间产物的芳香度越高，取代基越少，侧链越短，基质对VR中的活性反应组分在炭化早期生成的高度缩合物质的溶解度越大。     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

Interfacial strength and chemistry of additive-free silicon nitride ceramics brazed with aluminium

Two kinds of additive-free silicon nitride ceramics were brazed with aluminium; one was with as-ground faying surfaces and the other was with faying surfaces heat-treated at 1073K for 1.8 ksec in air. The heat-treatment of the silicon nitride ceramics formed a silicon oxynitride layer on the faying surfaces and increased the brazing strength of the joints. A silica-alumina non-crystalline layer and a β′-sialon layer were formed successively from the aluminium side at the interface of the joints. The heat-treatment which made the former layer thicker is a necessary process in making reliable, strong brazed joints.     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

Preparation and photochromism of nanocomposite thin film based on polyoxometalate and polyethyleneglycol

A photochromic nanocomposite based on Keggin structure phosphomolybdic acid (PMoA) well dispersed in polyethyleneglycol (PEG) was fabricated. TEM image showed that PMoA nanoparticles with narrow size distribution were finely dispersed in polymer matrix. FT-IR results showed that the Keggin geometry of polyoxometalates was still preserved inside the composites and strong coulombic interaction was built between PMoA and polymer matrix. Under UV irradiation, the film was reduced photochemically to yield a blue species, which was in accordance with a charge-transfer mechanism.