The determination of the pore structural parameters of isoporous resins by inverse GPC

The swollen pore structure of a series of microporous isoporous resins (7.4–140 Å) are investigated with inverse GPC, n-alkylbenzenes and linear polystyrenes being used as probe molecules. The results indicated that, with the lowering of crosslinking degree of isoporous resins, the average pore diameter increased and the pore distribution curve broadened. All pore volume distribution obeyed a log-normal distribution. Based on the linear regression method, the experimental data were fitted to a monotonously declining exponential function and a normal distribution function by a computer, and some important structural parameters such as average pore diameter, pore volume distribution, specific surface area, etc. were obtained. The specific surface area of swollen gels were found much greater than those in the dry state measured by N₂ adsorption.     

反相高效液相色谱法测定meso-四苯基卟啉钴的纯度

采用反相高效液相色谱法测定合成meso-四苯基卟啉钴的纯度;以甲醇乙腈二氯甲烷(体积比为55∶35∶10)为流动相,ShimpackCLCODS柱(150mm×6.0mmi.d,5μm)为分离柱,流速为1.5mL/min,检测波长420nm;meso四苯基卟啉钴的测定在1.0～10μg/mL时线性关系良好(相关系数r=0.9993),加标回收率为97.03%～101.42%,重复进样的相对标准偏差RSD为0.64%～2.92%(n=5)。方法的准确度高,精密度好,实际应用效果好。     

冷却器盘管失效分析及防范措施

本文介绍了冷却器盘管破裂泄漏的情况，分析了失效破坏的原因，并提出防止冷却器盘管破裂泄漏的措施。     

Electrochemical performance of nanocrystalline Li3V2(PO4)3/carbon composite material synthesized by a novel sol–gel method

A novel sol–gel method based on V₂O₅·nH₂O hydro-gel was developed to synthesize nanocrystalline Li₃V₂(PO₄)₃/carbon composite material. In this route, V₂O₅·nH₂O hydro-gel, NH₄H₂PO₄, Li₂CO₃ and high-surface-area carbon were used as starting materials to prepare precursor, and the Li₃V₂(PO₄)₃/carbon was obtained by sintering precursor at 750 °C for 4 h in flowing argon. The sol–gel synthesis ensures homogeneity of the precursors and improved reactivity. The sample was characterized by XRD, SEM and TEM. X-ray diffraction results show Li₃V₂(PO₄)₃ sample is monoclinic structure with the space group of P2₁/n. The TEM image indicates that the Li₃V₂(PO₄)₃ particles modified by conductive carbon are about 70 nm in diameter. The Li₃V₂(PO₄)₃/carbon system showed that the discharge capacities in the first and 50th cycle are about 155.3 and 143.6 mAh/g, respectively, in the range of 3.0–4.8 V. The sol–gel method is fit for the preparation of Li₃V₂(PO₄)₃/carbon composite material which may offer some favorable properties for commercial application.     

Phase Assemblages of Pr α-sialon Derived from SHS-ed Powders and TEM Study on the Nucleation of Pr α-sialon

The Pr α-sialon powders prepared by self-propagating high-temperature synthesis (SHS), consisting of 55 wt% Pr α-sialon and 45 wt% of β-sialon (abbreviated as α' and β'), were hot-pressed at 1800°C for 1 h. The results showed that Pr α' phase would transfer to β' with the appearance of JEM phase (Pr(Si_{6− z} Al _z )(N_{10− z} O _z )) after sintering, thus resulting in the increase of β' phase to 86 wt%. The addition of Y₂O₃ into SHS-ed Pr α' powders as the starting materials restrains the transformation of α' to β' and prevents the formation of JEM phase as well. The nucleation mechanism of Pr α' grain during hot-pressing was investigated in terms of transmission electron microscope and energy-dispersive spectrometer analysis. Two nucleation modes of Pr α' grains were found, i.e., nucleating on the undissolved Pr α' grains and on the nuclei of (Pr, Y) α' grains precipitated from liquid phase.     

A110－1－H／A110－1型氨合成催化剂在双筐并流合成塔中的使用

在双筐并流氨合成塔中使用了Ａ１１０－１－Ｈ／Ａ１１０－１型氨合成催化剂，使用寿命达１７４０天，累计产氨４３８３７８ｔ．该催化剂组合具有低温活性好、易还原、高催化活性、高抗毒能力、良好的热稳定性与破碎强度等优点．     

Synthesis and characterization of copolythiophene

Copolythiophenes (Co‐PTs), poly(3‐hexylthiophene‐co‐3‐thiophene carboxylic acid) (P3HT‐TCa), poly(3‐hexyloxylthiophene‐co‐3‐thiophene carboxylic acid) (P3HOT‐TCa), and poly(3‐phenylthiophene‐co‐3‐thiophene carboxylic acid) (P3PhT‐TCa), were synthesized by chemical oxidized polymerization to investigate the effect of copolymerization on the properties of polythiophenes (PTs). Gel permeation chromatography showed that the molecular weight (MW) of Co‐PT was lower than that of homopolythiophene. Fourier transform infrared (FTIR) spectra indicated that the copolymerization was successful between the monomers. The λ_max of Co‐PTs gave a “blue shift” in ultraviolet‐visible (UV‐VIS) spectra. Photoluminescence (PL) spectra showed that the PL intensity of Co‐PT became weaker than that of homopolythiophene and the disappearance of PL had been observed in P3HOT‐TCa. The thermal stability of Co‐PT was influenced by the carboxyl for its low decomposition temperature. Furthermore, the copolymerization between multi‐wall carbon nanotube containing thiophene ring (MWNT‐Th) and 3‐hexyloxylthiphene could also take place successfully. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Integrated size and topology optimization of skeletal structures with exact frequency constraints

The present paper studies the integrated size and topology optimization of skeletal structures under natural frequency constraints. It is found that, unlike the conventional compliance-oriented topology optimization problems, the considered problem may be strongly singular in the sense that the corresponding feasible domain may be disconnected and the global optimal solutions are often located at the tips of some separated low dimensional sub-domains when the cross-sectional areas of the structural components are used as design variables. As in the case of stress-constrained topology optimization, this unpleasant behavior may prevent the gradient-based numerical optimization algorithms from finding the true optimal topologies. To overcome the difficulties posed by the strongly singular optima, some particular forms of area/moment of inertia-density interpolation schemes, which can restore the connectedness of the feasible domain, are proposed. Based on the proposed optimization model, the probability of finding the strongly singular optimum with gradient-based algorithms can be increased. Numerical examples demonstrate the effectiveness of the proposed approach.     

橡胶对HIPS树脂落锤指标的影响

通过对高抗冲聚苯乙烯树脂出现产品落锤指标偏低问题的分析，从橡胶配量及其粒径大小上进行了改进，同时改进了工艺操作，采取了提高反应釜搅拌速度、降低乙苯浓度等措施。结果产品合格率达到９９％以上，优级品率达到９８％以上。     

电解法处理利福霉素SV钠废渣分离液的研究

根据电化学原理，采用电解法，利用铁屑与炭粒作电极，处理利福霉素SV钠药渣分离液，讨论各种因素对分离液污染物作效果的影响，COD去除率可达91．8％左右，脱色率可达95％左右。