CDMA发射分集系统的多用户检测常模算法分析

空时分集技术的最大优点在于在不增加带宽的情况下可以提高系统的可靠性,是目前移动通信的研究热点.常模算法是一种性能优良的码分多址(CDMA)盲多用户检测技术,能确保判决信号与实际传送信号之间的差错较小,误码率性能良好.文中提出将标准线性受限常模算法(LCCMA)与空时分组码(STBC)相结合,设计出一种收敛快、能够改善系统性能的基于2-空时分组码的多用户接收机.     

以寻呼区分析为基础的PHS网络优化方法

通过分析PHS网络中各寻呼区的统计指标,剖析指标劣化的根本原因,采取修改相应的参数配置、移站、调整天线等措施进行网络优化,优化实施后再次收集统计指标做对比分析,总结经验。     

Traveling-wave piezoelectric linear motor Part I: the stator design.

A new type of piezoelectric linear motor incorporating a traveling wave has been developed. The linear motor is comprised of a stator and a carriage. The stator design, which consists of a meander-line structure and gear teeth mounted on the meander-line structure, is the focus of this article. The meander-line structure is constructed with bimorph actuators arranged in a line. These actuators are driven by two phased sets of alternating current (ac) in order to generate a traveling wave. The traveling wave is transferred to the gear teeth, by which the carriage is driven. Modeling of the stator is derived by use of a strain energy method. The performance of various materials is evaluated by analytical and experimental methods. The analytical and the experimental results are quite approximate. Modal analysis is investigated using ANSYS. Appropriate modes associated with ultrasonic levels of resonant frequency are selected to obtain desired motion and to enhance the output performance. Surface speed for various applied input voltage are studied and indicate a nearly linear relationship. The stator in combination with the carriage makes up the linear motor.     

Fatigue Behavior and Retrofit Investigation of Distortion-Induced Web Gap Cracking

This paper studies a Kansas Department of Transportation welded plate girder bridge that developed fatigue cracks at small web gaps close to the girder top flange. Repair had been previously performed by softening the connection plate end with a slot retrofit, but cracks were recently found to have reinitiated at some of the repaired details and are again propagating. A comprehensive finite-element method study was performed to investigate the cracking behavior observed in the bridge and to recommend appropriate measures for future bridge retrofit. The analytical results show that stresses developed at the top flange web gaps could exceed yielding under the loading of an HS15 fatigue truck. The current slot repair used in the bridge was found to have introduced higher magnitude fatigue stresses in the web gap. To achieve a permanent repair of the bridge, it is recommended that a welded connection plate to flange attachment be used during future bridge retrofit. The web gap details should be able to withstand unlimited number of load cycles once this additional repair is performed.     

自动线性跟踪Butterworth有源滤波器研究

滤波是通信、测试、数据采集和实时控制等领域至关重要的环节。通常的模拟滤波器，由于截止频率固定，在某些宽频率动态范围且有实时性要求的应用场合，往往达不到预期的滤波效果，有时甚至影响整个系统的正常运行。本文从有源滤波器的机理分析入手，提出了一种由单片机参与的滤波系统，它能自动跟踪输入信号频率，线性地选择合适的滤波器截止频率，弥补了原有滤波器的不足。     

逆向反射镜光度测量

为了正确评价逆向反射镜的加工质量与使用效果，且将二者有机地统一起来，本文提出应根据测试目的来选择合适的光度测量方法，并进一步分析了不同测试目的将导致测量装置的组成、几何条件（距离，孔径角，工作姿态等）、光度条件（光源色温、稳定性与均匀性，接收器线性、灵敏度与光谱修正等）、测量参数（反光强度系数、逆反射系数、逆亮度系数等）等各不相同。     

Carbon Nanotubes Grown on the Surface of Cathode Deposit by Arc Discharge

Carbon nanotubes prepared by de arc discharge of graphite electrodes in He and CH₄ gas took markedly different morphology. Thick nanotubes embellished with many carbon nanoparticles were obtained by evaporation under high CH₄ gas pressure and high arc current. Thin and long carbon nanotubes were obtained under a CH₄ gas pressure of 50Torr and an arc current of 20A for the anode with a diameter of 6mm.     

快速烧结法制备连续碳化硅纤维

通过熔融纺丝，不熔化处理制得连续聚碳硅烷（ＰＣＳ）不熔化纤维，采用快速烧结方法制备出性能较好的连续ＳｉＣ纤维。探讨了气封条件的选择，以及烧结速度对ＳｉＣ纤维的组成，结构及性能的影响。结果表明，快速烧结条件下，可以实现向纤维上施加张力以及纤维的无机化转变，烧结速度加快会降低纤维的Ｃ／Ｓｉ（原子比），同时有利于提高纤维的抗拉强度和热稳定性。     

WC对Cu/WC_P复合材料性能及组织的影响

通过ＷＣ含量对ＷＣ／Ｃｕ复合材料性能的影响，确定了冷压－烧结法制备Ｃｕ／ＷＣ材料的适宜ＷＣ含量为１０ｖｏｌ％左右。并就ＷＣ对该材料组织和再结晶行为的影响进行了有益的探讨。     

套管固井质量问题及对策分析

从油田现场反应的情况出发，对调整井固井，尾管固井，大位移井套管固井和其他固井的质量问题进行了分析，针对各种问题产生的原因，提出了相应换解决办法。