Bearing Failure Optimization of Composite Double-Lap Bolted Joints Based on a Three-Step Strategy Marked By Feasible Region Reduction and Model Decoupling

To minimize the mass and increase the bearing failure load of composite doublelap bolted joints, a three-step optimization strategy including feasible region reduction, optimization model decoupling and optimization was presented. In feasible region reduction, the dimensions of the feasible design region were reduced by selecting dominant design variables from numerous multilevel parameters by sensitivity analyses, and the feasible regions of variables were reduced by influence mechanism analyses. In model decoupling, the optimization model with a large number of variables was divided into various sub-models with fewer variables by variance analysis. In the third step, the optimization sub-models were solved one by one using a genetic algorithm, and the modified characteristic curve method was adopted as the failure prediction method. Based on the proposed optimization method, optimization of a double-lap single-bolt joint was performed using the ANSYS^® code. The results show that the bearing failure load increased by 13.5% and that the mass decreased by 8.7% compared with those of the initial design of the joint, which validated the effectiveness of the three-step optimization strategy.     

Nb和时效时间对热轧中锰TRIP钢中P偏聚的影响

热轧态中锰TRIP钢首先经650 ℃退火2 h,随后在550 ℃进行等温时效热处理,采用场发射扫描电镜(FE-SEM)研究该钢中P的偏聚和时效析出行为的变化情况。结果表明,中锰TRIP钢中P在晶界的偏聚是一种非平衡偏聚现象,临界时间约为50 h,与理论计算结果48 h较为吻合。在局部偏聚区域内,C与P存在共偏聚的关系,即P偏聚量高的地方,C含量也高。而合金元素Nb具有抑制P偏聚的效果,在20~70 h时效时间内,可以相对降低6.57%~19.5%的最大P偏聚量。根据电子背散射衍射(EBSD)菊池线分析,P偏聚量低于2.28at%时,P为固溶状态,高于2.28at.%时,P为析出状态。     

Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The microstructure and mechanical properties of Mg–6Zn–1Y and Mg–6Zn–3Y(wt%) alloys under different cooling rates were investigated. The results show that the second dendrite arm spacing(SDAS) of Mg–6Zn–1Y and Mg–6Zn–3Y is reduced by 32 and 30% with increasing cooling rates(Rc) from 10.2 to 23 K/s, which can be predicted using a empirical model of SDAS=68 R 0:45:45cand SDAS=73 R 0c, respectively. The compressive strength of both alloys increases with increasing the cooling rate, which is attributed to the increase of volume fraction(Vf) of secondary phases under high cooling rate. The interaction of the cooling rate and component with SDAS has been theoretically analyzed using interdependence theory.     

Influence of Si-Doping on the Performance of InGaN/GaN Multiple Quantum Well Solar Cells

Semiconductors - The performance of InGaN/GaN multiple quantum well (MQW) solar cells with five different Si-doping concentrations, namely 0, 4 × 1017 cm–3, 1 × 1018 cm–3, 3...     

Optimal Guaranteed Cost Tracking of Uncertain Nonlinear Systems Using Adaptive Dynamic Programming with Concurrent Learning

In this paper, based on adaptive dynamic programming (ADP) with concurrent learning, the problem of optimal guaranteed cost tracking is studied for a class     

改善硫精矿浓密机溢流跑浑试验研究

本文旨在改善某选厂硫精矿浓密机溢流跑浑问题,对生产现场进行勘察和分析,分析浓密机溢流跑浑的原因,并开展原矿配比和沉降试验研究。对采场原矿矿样和硫精矿矿浆进行系统的试验研究,分别采用不同沉降方案进行条件试验,考察絮凝剂种类、絮凝剂用量、pH调整剂用量、不同药剂之间的配比等条件对沉降的影响,确定合适的原矿配比及合理药剂制度,有效地控制金属在溢流中的损失,充分获取现有产品的蕴含价值。     

Road Extraction from High Resolution Remote Sensing Image based on Shape Analysis with Gestalt Theory

Simulating the psychological experience of human vision，a road extraction model based on the format tower is proposed to extract the road in the high resolution remote sensing image from the perspective of morphology.Firstly，based on the spectral and texture information，the suspected road targets are extracted by using segmentation technology.Then these targets are classified according to their reliability and extract the road targets for each category.Finally，three types of identified road information are verified and merged，and the continuous smooth road extraction results are obtained.Experiments on real high resolution images show that the results are consistent with the visual perception of the human eye，and the overall classification accuracy is higher，indicating that the algorithm is effective and feasible and has good use value.