新型刮刀钻头的设计及现场试验研究

在理论分析的基础上，综合PDC钻头和刮刀钻头的优点，设计了一种新型的刮刀钻头，并进行了现场试验。现场试验结果表明，该钻头运转平稳，采用低钻压、高转速，钻进速度快，井眼规则通畅，有较明显的防斜作用，该种钻头的推广应用对提高钻井工程的整体效益具有十分重要的意义。     

工程钻机在沙卵石地区的物探钻井

川西平原属沉积平原，不到2m厚的表土下面全是沙卵石，沙卯石厚度达二、三十米。地面覆盖农田，沟垄纵横，限制了车载钻机的进入。以往地震勘探多采取浅井组合方式激发，所获得的地震资料能量差、面波强，对农田破坏面积大。若使用SH30—2A型轻便工程钻机，配上自制的冲击管，采取冲击钻进，从管中下药柱的方式，可实现沙卵石地区的深井激发，提高资料采集质量，且效率高、成本低。     

Aging response of the young’s modulus and mechanical properties of Ti-29Nb-13Ta-4.6Zr for biomedical applications

Alloys for implant devices require improved strength but a reduced Young’s modulus, in order to become mechanically more compatible with adjacent bone tissues. In this study, a new metastable β-type titanium alloy, Ti-29Nb-13Ta-4.6Zr (wt pct), was subjected to aging treatment to produce different microstructures, and the resulting mechanical properties, including the Young’s modulus, were measured. The Young’s modulus of this alloy is found to be sensitive to microstructures generated by various heat treatments. For microstructures varying from (α + β) to (α + β + ω) and (β + ω), the Young’s modulus increases with an accompanying increase in tensile strength and hardness, but decreases in ductility. The (β + ω) microstructure has a low strength, high modulus, and poor ductility and cannot be used for biomedical applications. For an (α + β) microstructure, the volume fraction of the phases is shown to be the main factor that determines the mechanical properties.     

Collision-Free Interleaver Composed of a Latin Square for Parallel-Architecture Turbo Codes

In parallel-architecture turbo codes, the constituent interleavers must avoid memory collision. This paper proposes a collision-free interleaver structure composed of a Latin square (LS) and pre-designed interleavers. Our proposed interleavers can be easily optimized for various information block sizes and for various degrees of parallelism. Their performances were evaluated by computer simulation.     

烧结成品运输自动控制系统的改进

对烧结成品运输自控系统不稳定性因素进行了分析，提出了采取优化硬件外围工作环境，完善软件保护程序等改进措施。改进后的自控系统稳定性明显提高。     

公司大门工程建设施工

大门小品建筑属多项目综合性工程。本文作者从管理者的角度 ,通过对公司大门及附属工程施工质量控制的总结 ,说明了质量控制应贯穿于工程施工的全过程     

Effects of Y and Ce on Microstructures and Properties of Nb-Si System Composites

The effects of yttrium and cerium on microstructures and properties of Nb-Si system composites were investigated by scanning electron microscopy( SEM), energy dispersive spectrum(EDS), X-ray diffraction(XRD) and high temperature oxidation experiments.It is found that the coarse primary silicide phase became finer and more homogeneous with Y and Ce addition.The results of high temperature oxidation experiments show that the oxidation rates of NbSi system composites with an appropriate amount of Y and Ce decrease compared with those of alloys without Y or Ce addition, and oxidation products mainly distribute along the phase boundaries between the Nb solid solution and silicide.     

Sol-Gel Preparation of LaNiO3 and Its Physical and Chemical Properties

LaNiO3 was synthesized by sol-gel method in which lanthanum nitrate and nickel nitrate were used as start materials and citric acid was used as complex for gel formation.The precursor was dried and subsequently heated at elevated temperature to form the desired product.XRD analysis shows that pure LaNiO3 was synthesized.Electrical conductivity and electrochemical performance of the material were tested.The electrical conductivity decreases from 34.5that there are current peaks in the curve, which is the evidence of the electrochemical activity of LaNiO3.     

技术攻关提高成材率

介绍了广钢集团高速线材生产线的生产和工艺概况，分析了成材率的影响因素，阐述了技术攻关提高成材率所采取的措施和取得的良好效果及经济效益。     

赴日无线电监测技术考察报告

首先介绍了日本总务省关东综合通信局电波监理部的情况，然后对日本安立公司生产的RR510A型无线电监测接收机和技术参数以及MS8609A型数字移动无线发射机测试仪的功能进行了分析和介绍。