GSM与WCDMA无线网络规划比较

WCDMA与GSM在空中接口上存在较大差异,WCDMA基于码分多址技术,GSM基于时分多址技术。GSM主要处理语音和低速数据,而WCDMA引入了多种速率的数据业务,根据业务的QoS进行资源控制和分配,因此在无线网络规划方法上,WCDMA与GSM存在较大差异。文章从容量规划、覆盖规划、蜂窝布局、规划流程、网络评估等方面对WCDMA与GSM的无线网络规划进行了比较和分析。     

Mechanism of resistance microwelding of crossed fine nickel wires

Resistance microwelding of fine crossed nickel wires is of increasing industrial importance for electrical connections in downsized electronic and medical devices, but the understanding of the process is very limited. A study has, therefore, been performed to clarify the basic joining mechanisms, in which the effects of main process parameters (welding current and force and weld time) were investigated by detailed mechanical testing and metallurgical examinations. A bonding mechanism with main process stages (wire cold collapse, surface melting, molten-phase squeeze-out and, solid-state bonding) was proposed. A new technique has also been developed to optimize the process by initiating the welding current well before the electrode force has reached its full nominal value.     

In situ polymerization and characterization of polyester‐based polyurethane/nano‐silica composites

Polyester‐based polyurethane/nano‐silica composites were obtained via in situ polymerization and investigated by Fourier‐transform infrared spectroscopy (FTIR), or FTIR coupled with attenuated total reflectance (FTIR‐ATR), Transmission electron microscopy (TEM), atomic force microscopy (AFM), an Instron testing machine, dynamic mechanical analysis (DMA) and ultraviolet‐visible spectrophotometry (UV‐vis). FTIR analysis showed that in situ polymerization provoked some chemical reactions between polyester molecules and nano‐silica particles. FTIR‐ATR, TEM and AFM analyses showed that both surface and interface contained nano‐silica particles. Instron testing and DMA data showed that introducing nano‐silica particles into polyurethane enhanced the hardness, glass temperature and adhesion strength of polyurethane to the substrate, but also increased the resin viscosity. UV‐vis spectrophotometry showed that nano‐silica obtained by the fumed method did not shield UV radiation in polyurethane films. Copyright © 2003 Society of Chemical Industry     

Programmable group-delay module using binary polarization switching

We demonstrate the first programmable group-delay module based on polarization switching. With a unique binary tuning mechanism, the device can generate any differential group delay value from -45 to +45 ps with a resolution of 1.40 ps, or any true-time-delay value from 0 to 45 ps with a resolution of 0.7 ps. The delay varying speeds for both applications are under 1 ms and can be as fast as 0.1 ms. We evaluate both the dynamic and static performances of the device while paying special attention to its dynamic figures of merit for polarization-mode dispersion emulation and compensation applications. Our experiment shows that the device exhibits a negligible transient-effect induced power penalty (<0.2 dB) in a 10-Gb/s nonreturn-to-zero system.     

应用均匀设计法研究安息香缩合工艺

利用均匀设计法通过SPSS10.0计算机软件研究了反应条件对安息香缩合的影响。从而获得优化的工艺条件，与正交试验相比，该法试验次数少。工作效率高，并且便于分析各种因素的影响。     

分割电极片状压电致动器——(二)位移特性及狭缝宽度对其影响的实验研究

研究了悬臂梁式分割电极片状压电致动器的位移特性。理论分析表明，分割电极狭缝宽度会减小致动器自由端的位移输出，但当狭缝宽度小于致动器电极宽度的１０％时，可忽略狭缝宽度的影响。致动器端部位移的测试结果大于理论计算值。与现有磁头悬浮臂尺寸相近的致动器，在２０Ｖ～５０Ｖ的电压驱动下均可获得１μｍ～２μｍ的致动位移。对９８５０道／厘米的密度磁盘，该位移能覆盖至少一个磁道宽度，满足磁头定位两级伺服系统对第二级致动器位移的基本要求。     

Pore size control of porous silica by sol-gel process

Porous silica glass was prepared by sol-gel process from tetraethoxysilane (TEOS). The effects of solvents (water, ethanol), drying condition, heat treatment temperature on specific surface area and pore size distribution of porous silica were investigated. Gelation process accelerates with an increase of H₂O content, while retards with the increase of ethanol amount. Structure changes during heat treatment were studied by means of DTA, XRD. TEM micrographs show that the gel particles shrink after heated at 500°C, thus the average pore size decreases.     

���þ��ܰ�ȫ�Բ�������������

本文通过对在用钻机井架的现场实际测试,建立数据库、测评模型,对实测的数据用计算机技术进行分析,提出了初始弯曲应力;数据正态分布检验——x～2检验;建立回归方程;在给定置信度下测评当前承载能力的技术概念。解决了在用钻机A型井架的安全性评估问题,是一种较为合理、可靠、科学的测评技术和方法。