基于R语言的机器人教育微博可视化研究

本文利用R语言对关注度不高、转发量不太大的机器人教育微博进行了可视化研究。在分析技术实现过程的同时,我们得出结论是:机器人教育的舆情由教育官方媒体和企业培训机构主导;经济力量决定着参与讨论的程度;微博不是学习内容交流的主阵地。     

改性聚酰亚胺在摩托车中的应用

本研究选择了改性聚酰亚胺、改性聚甲醛、改性尼龙三种材料应用于摩托车衬套制品,进行了对比试验,结果表明:采用改性聚酰亚胺的衬套具有强度高、耐磨损、尺寸稳定性好等特点,完全达到该产品设计的要求。     

基于前向预测并行追踪的视频压缩传感方法

为了减小视频信号采集端的负担,提出一种基于压缩传感理论的视频压缩算法模型。该模型采用广义轮换矩阵获取视频帧的测量值,再结合视频压缩的运动补偿预测关键技术,消除视频帧间冗余。然后在并行贪婪追踪算法中引入前向预测技术作为重构算法,最终获取重构的压缩图像。实验对比了在不同算法下的重构图像和不同采样比下不同算法的重构PSNR值,然后利用所提方法得到视频序列的重构压缩图像。实验结果表明,该算法模型能较精确地获取压缩的视频图像,适合在视频压缩中应用。     

Flow and Flow Decay of Refractory Castables

Installation of refractory castables depend not only on flow,but also on how soon the flow is lost because of setting.The loss of flow(flow decay)has always been one of the main problems of refractory castable manufacturers,a problem that has not been too well described in literature.The flow decay has been studied for a castable system based on alumina,pointing out some general trends.The flow decay was found very temperature sensitive,being strongly accelerated by temperature increases.To compensate for excessive flow loss,a retarder like citric acid may be used.Thus flow decay was measured as a function of citric acid(retarder) addition at 35℃.     

热压氮化硅在1200℃的高温疲劳损伤

研究了热压氮化硅陶瓷的室温和高温力学性能及在１２００℃的高温疲劳损伤行为，发现材料的弹性模量、抗变强度与断裂韧性均随温度升高而下降，但在１０００℃以上降低最为显著。在１２００℃高温疲劳寿命与应力之间符合单对数线性关系经分析发现这种现象与失效的热激活过程有关。通过对实验数据，ＸＲＤ相结构、变形动力学过程和断口的微观分析证明，陶瓷高温疲劳失效机理为“杂质空穴复合作用机制”。对热压氮化硅来说，失效机理主     

粉煤灰填充PVC树脂的研究

采用ＷＡＸＤ、ＳＥＭ和力学测试等方法对不同粒度和不同含量的粉煤灰（ＰＦＡ）与聚氯乙烯（ＰＶＣ）共混物的结构形态、力学性能进行了测定。结果表明，ＰＦＡ粒度对ＰＶＣ／ＰＦＡ共混物的性能具有明显影响，当ＰＦＡ粒度尺寸达到一定程度时，再降低ＰＦＡ粒度尺寸对共混物的性能影响不大。随着ＰＶＣ／ＰＦＡ共混物中ＰＦＡ含量的增加，拉伸强度和拉伸模量增大，但伸长率降低。     

沉积温度对微波热解CVI制备碳/碳复合材料密度及组织结构的影响

以碳毡为预制体,N2为稀释气体,甲烷为碳源前驱体,其分压为10 kPa,滞留时间为0.15 s的工艺条件下,研究了不同沉积温度对微波热解化学气相渗透(chemical vapor infiltration,CVI)工艺制备碳/碳复合材料的致密化速率、样品的体积密度及其密度均匀性的影响,并对其组织结构进行了观察.分析了沉积温度对微波热解CVI工艺制备碳/碳复合材料的密度与组织结构的变化规律.结果表明:在微波热解CVI工艺中,随着沉积温度的降低,碳毡预制体的致密化速率及最终体积密度呈现先升后降,1100 ℃沉积制备复合材料的密度均匀性最好,并呈现从内到外逐步沉积的规律.热解碳的织构主要为中等织构.     

抗静电可染丙纶的结构与性能

研究了聚丙烯、抗静电组分、可染组分三元共混体系纤维的抗静电性能、力学性能、染色性能及形态结构。研究表明：抗静电组分和可染组分有一定的相互影响，当抗静电组分加入量在４％～６％；而可染组分加入量在８％～１０％时为共混体系的最佳配合范围，共混纤维成品丝既表现出良好的抗静电性能，又表现出良好的可染性能，实现了常压沸染深色的效果。还发现，共混纤维拉伸丝的比电阻小于卷绕丝的比电阻。     

Composite anion exchange membrane for alkaline direct methanol fuel cell: Structural and electrochemical characterization

A copolymer of 4‐vinylpyridine (4‐VP) and styrene was synthesized by radical mass polymerization using 2,2′‐azobisisobutyronitrile as initiator. An insoluble (linear) pyridinium‐type polymer was prepared by the reaction of P (4VP–St) with 1‐bromooctane. An anion exchange membrane was prepared using a composite of pyridinium‐type polymer and a fibrous woven structure for use in electrochemistry. The composite membrane was characterized by X‐ray diffraction, tensile strength, scanning electron microscopy, and electrochemistry measurements. The experimental results showed that the fibrous woven product had improved the tensile strength more than had the membrane made of a pyridinium‐type polymer alone. The composite membrane was used in alkaline fuel cells, and its properties were measured by electrochemical analysis. The ionic conductivity of the membrane was acceptable, but its performance as a direct methanol fuel cell (DMFC) was not. The primary reason for this was analyzed, and research is ongoing, with analysis to be discussed in later reports. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2248–2251, 2006     

汉语框架网中未登录词元的框架选择

汉语框架网的低覆盖率导致汉语句子中存在许多未登录的词元,严重制约着汉语的框架语义分析任务。针对未登录词元的框架识别问题,该文借助同义词词林的词义信息,提出基于平均语义相似度计算及最大熵模型两种方法,采用静态特征与动态特征相结合的特征选择方法。实验证明,这两种方法都能有效地实现未登录词元的框架选择,基于相似度计算的方法(TOP-4)获得78.61%的准确率;基于最大熵的方法结果可达87.29%,同时在新闻语料上达到了75%的准确率。