Influence of filling ratio and working fluid thermal properties on starting up and heat transferring performance of closed loop plate oscillating heat pipe with parallel channels

Using ethanol or acetone as the working fluid, the performance of starting up and heat transfer of closed-loop plate oscillating heat pipe with parallel channels(POHP-PC) were experimentally investigated by varying filling ratio, inclination, working fluids and heating power. The performance of the tested pulsating heat pipe was mainly evaluated by thermal resistance and wall temperature. Heating copper block and cold water bath were adopted in the experimental investigations. It was found that oscillating heat pipe with filling ratio of 50% started up earlier than that with 70% when heating input was 159.4 W, however, it has similar starting up performance with filling ratio of 50% as compared to 70% on the condition of heat input of 205.4 W. And heat pipe with filling ratio of 10% could not start up but directly transit to dry burning. A reasonable filling ratio range of 35%-70% was needed in order to achieve better performance, and there are different optimal filling ratios with different heating inputs- the more heating input, the higher optimal filling ratio, and vice versa. However, the dry burning appeared easily with low filling ratio, especially at very low filling ratio, such as 10%. And higher filling ratio, such as 70%, resulted in higher heat transfer( dry burning) limit. With filling ratio of 70% and inclination of 75°, oscillating heat pipe with acetone started up with heating input of just 24 W, but for ethanol, it needed to be achieved 68 W, Furthermore, the start time with acetone was similar as compared to that with ethanol. For steady operating state, the heating input with acetone was about 80 W, but it transited to dry burning state when heating input was greater than 160 W. However, for ethanol, the heating input was in vicinity of 160 W. Furthermore, thermal resistance with acetone was lower than that with ethanol at the same heating input of 120 W.     

Thermal energy storage properties of a capric acid/stearic acid binary system and a 48# paraffin/liquid paraffin binary system

In this paper, the phase change temperature, latent heat and thermal stability of a capric acid/stearic acid binary system and a 48# paraffin/liquid paraffin binary system were experimentally studied. The experimental results showed that the phase change temperature and phase change latent heat change with the content of the component. The phase change temperatures of binary mixtures change in a wide range, so they can be used in different fields by adjusting the mixing ratio. The phase change latent heat of fatty acid mixtures is higher than that of paraffin mixtures. The thermal stability of fatty acid mixtures is better than that of paraffin mixtures. The mixtures used in the phase change material wall or the phase change material floor as energy storage materials were given in the paper.     

Flat-plate collector construction and system configuration to optimize the thermosiphonic effect

Thermosiphon systems heat potable water or heat transfer fluid and use natural convection to transport it from the collector to storage. This type of technology is applied extensively in countries with good sunshine potential. One such example is Cyprus, which is currently the leading country in the world with respect to the application of solar water heaters for domestic applications, with more than 93% of the houses equipped with such a system. The performance of such a system depends on many factors including the collector construction and the arrangement of the system, mainly with respect to the distance between the top of the solar collector and the bottom of the storage tank and the solar collector slope, which affects both the energy collected and the hydrostatic pressure of the system. A typical system in Cyprus uses 3 m² of collectors, 160 l storage, its collectors are usually inclined at 45° from horizontal and has 15 mm copper riser tubes and header tubes with a diameter of 28 mm. The collector absorber plate is also made from copper. The main objective of this paper is to investigate through modeling and simulation possible configurations, which will optimize the performance of the system. For this purpose, a number of riser and header tube diameters were considered ranging from 6 mm to 35 mm, slopes from 20° to 90° and distances between the top of the collector to the bottom side of the storage tank ranging from ±15 cm. The system is modeled using TRNSYS and simulated with the Typical Meteorological Year (TMY) of Nicosia, Cyprus. The results showed that the best-optimized system is obtained for small header and riser pipe diameters and very close performance is obtained for various combinations. Therefore, the decision on the optimum system should depend on cost issues, which are currently very important because of the increased price of copper and operational problems depending on the hardness of the water in the area of installation, which could cause scale deposits that could clog the riser pipes. The optimum slope is found to be equal to the latitude plus 10°, i.e., 45°, although a smaller slope does not affect the performance a lot, and the optimum distance between the top of the collector and the bottom of the storage tank is −15 cm. These findings should prove valuable for the collector and systems designers and manufacturers.     

Effect of small Sn–3.5Ag–0.5Cu additions on the structure and properties of Sn–9Zn solder in ball grid array packages

Sn–9Zn with various additions of Sn–3.5Ag–0.5Cu powder was prepared by mechanically dispersing different weight percentages (1, 3, 5 and 7) of Sn–Ag–Cu powder into Sn–9Zn solder paste. In the Sn–Zn solder, scallop-shaped AuZn₃ intermetallic compound was found at the interfaces. On the other hand, in the Sn–3.5Ag–0.5Cu content solders, an additional ε-AgZn₃ intermetallic compound layer was found to be well adhered on the top surface of the AuZn₃ layer and the ε-AgZn₃ layer thickness increased with the number of reflow cycles. In addition, fine spherical-shaped ε-AgZn₃ intermetallic compound particles as well as an acicular-shaped Zn-rich phase was clearly observed in the β-Sn matrix. On increasing the Sn–Ag–Cu content, the shear load was increased from 1.80 to 2.03 kg after one reflow cycle. In the Sn–3.5Ag–0.5Cu content solders, the fracture surfaces exhibited typical ductile behavior with very rough dimpled surfaces while the fracture surface in the Sn–Zn solder gave fractures with a brittle appearance. In the fracture surface of the Sn–3.5Ag–0.5Cu content solders, some dimples were clearly observed associated with the formation of spherical-shaped ε-AgZn₃ intermetallic compound particles.     

Heat transfer performance analysis of a solar flat-plate collector with an integrated metal foam porous structure filled with paraffin

The analysis of energy storage process of a solar flat-plate collector with an integrated aluminum foam porous structure filled with paraffin as the phase-change medium is reported in this paper. The momentum conservation of liquid paraffin is modeled with Darcy’s law with the Brinkman–Forchheimer’s extension, while heat transfer between the metal foams and paraffin in solid and liquid phases is modeled with a two-temperature model. It is shown that the assumption of the local thermal equilibrium between the metal foams and paraffin invoked in previous studies is inappropriate in predicting the heat transfer behavior, whereas the two-temperature model proposed in this work without this assumption can more realistically predict the real-world phase-change heat transfer process in the solar collector. In particular, the numerical results indicate that the heat transfer performance can be significantly improved by using the aluminum foams filled with paraffin.     

MO-LCAO calculations on polymethines: XXIII-the origin of the absorption colour of dithizone and related compounds

The two intense absorption bands of dithizone at about 440 and 620 nm give rise to the green colour observed in solution. In contrast to the view prevailing in the literature, the two colour bands are due to a single tautomer that has the diazatrimethinium thiolate rather than thiocarbazone or mercaptoformazan structure. This follows from quantum-chemically supported colour-structure relationships between dithizone and related compounds. Chromophorically dithizone belongs to the cyanine dyes. Internal substitution of CH of the trimethine chain by aza-type nitrogen atoms and additional me so-substitution by thiolate sulfur imparts to the trimethine cyanine a significant bathochromicity and brings about its unique chromophoric properties due to its two intense colour bands.     

New generation of oil and grease seals

SKF has developed a new generation of oil and grease seals specifically for heavy-duty applications. These seals are intended for use in agricultural and similar machinery where environmental and operating conditions can be harsh.Tractor design during the 1990s has moved towards the development of improved sealing technology for oil and grease seals for transmission components. Seals need to be able to perform in all types of environment, regardless of the application.     

集中供热系统不同调峰供热方式的技术经济性分析

本文主要分析了分布式调峰供热方式在集中供热系统应用中的技术经济性。通过节能性和经济性对比分析可知,相对于集中调峰供热方式,分布式调峰供热方式可以降低集中供热系统的供热能耗,提高承担基础负荷的集中热源的满负荷运行小时数、提高集中热源的供热效率,同时可以降低一次供热管网的初投资、减少一次供热管网的热损失。     

Build-up and long-term performance test of a full-scale solar-assisted heat pump system for residential heating in Nordic climatic conditions

This paper presents the build-up and long-term performance test of a full-scale Solar-Assisted Heat Pump System (SAHPS) for residential heating in Nordic climatic conditions. This particular SAHPS was developed within the EU project ENDOHOUSING, by predominantly using components and techniques that are available on the market. The analysis primarily focuses on system performance, with emphasis on Heat Pump (HP) and total system Seasonal Performance Factor (SPF), based on long-term and full-scale operation. Analysis shows that despite unfavourable building conditions, for low energy use and utilisation of a SAHPS, the system was successfully in full operation (for about 2 years) fulfilling heating requirements. Data processing of the series representing the full year period of 2007(February)–2008(February), presented a HP and total SAHPS performance of: SPF_HP = 2.85 and SPF_SAHPS = 2.09. The authors argue that with an optimised SAHPS control and operation strategy, additional use of circulation pumps and energy (electricity) could be vastly reduced, hence attaining a SPF_SAHPS value that is in parity with the SPF_HP. As the Nordic (Swedish) Endohousing SAHPS has not yet been properly optimised/designed and installed in an appropriate house, the SPF_HP = 2.85 is considered satisfactory.