微计算机控制的造波系统

本文所述系统可在水池中产生单一频率规则波、周期不规则波及"随机波",用于海洋、造 船工程的模型试验,采用频域迭代法和成型滤波器法来产生模拟海浪.尽管这一控制系统是 专为产生模拟海浪而设计的,但其控制方案也可直接用于其他测试技术领域,以产生"随机" 信号.     

桩柱式采金船每帮挖方量的理论计算

本文从理论上推导出了桩柱式采金船每帮挖方量计算的数学模型并，可广泛地用于设计与生产中，从而提高采金船设计的准确性，以及对生产矿山进行矿量、回收率和实收品位等采选指标收测的可靠性。     

Performance of miniaturized direct methanol fuel cell (DMFC) devices using micropump for fuel delivery

A fuel cell is a device that can convert chemical energy into electricity directly. Among various types of fuel cells, both polymer electrolyte membrane fuel cells (PEMFCs) and direct methanol fuel cells (DMFCs) can work at low temperature (<80 °C). Therefore, they can be used to supply power for commercial portable electronics such as laptop computers, digital cameras, PDAs and cell phones. The focus of this paper is to investigate the performance of a miniaturized DMFC device using a micropump to deliver fuel. The core of this micropump is a piezoelectric ring-type bending actuator and the associated nozzle/diffuser for directing fuel flow. Based on the experimental measurements, it is found that the performance of the fuel cell can be significantly improved if enough fuel flow is induced by the micropump at anode. Three factors may contribute to the performance enhancement including replenishment of methanol, decrease of diffusion resistance and removal of carbon dioxide. In comparison with conventional mini pumps, the size of the piezoelectric micropump is much smaller and the energy consumption is much lower. Thus, it is very viable and effective to use a piezoelectric valveless micropump for fuel delivery in miniaturized DMFC power systems.     

A probabilistic method for calculating the usefulness of a store with finite energy capacity for smoothing electricity generation from wind and solar power

This paper describes a novel method of modelling an energy store used to match the power output from a wind turbine and a solar PV array to a varying electrical load. The model estimates the fraction of time that an energy store spends full or empty. It can also estimate the power curtailed when the store is full and the unsatisfied demand when the store is empty. The new modelling method has been validated against time–stepping methods and shows generally good agreement over a wide range of store power ratings, store efficiencies, wind turbine capacities and solar PV capacities.Example results are presented for a system with 1 MW of wind power capacity, 2 MW of photovoltaic capacity, an energy store of 75% efficiency and a range of loads from 0 to 3 MW average.     

浅谈变频调速在企业自备电站中的应用

简要阐述了变频调速的原理，介绍调速控制在自备电站中的应用情况。     

大空域机动巡航导弹的模糊PID控制器设计

针对大空域机动巡航导弹下降转平飞过程中出现的强非线性特点．在俯仰通道设计了模糊PID双模控制方案。以高度误差和该误差变化量为输入．以高度误差为阀限．在高度误差较大时采用响应迅速的模糊控制器．较小时采用稳态精度较高的PID控制器。最后通过仿真表明通过该方案所控制的弹道符合方案弹道．满足设计指标要求。     

Synthesis and electrochemical properties of layered Li[Ni0.333Co0.333Mn0.293Al0.04]O2−zFz cathode materials prepared by the sol–gel method

The cathode-active materials, layered Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_2−zF_z (0 ≤ z ≤ 0.1), were synthesized from a sol–gel precursor at 900 °C in air. The influence of Al–F co-substitution on the structural and electrochemical properties of the as-prepared samples was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and electrochemical experiments. The results showed that Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_2−zF_z has a typical hexagonal structure with a single phase, the particle sizes of the samples tended to increase with increasing fluorine content. It has been found that Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_1.95F_0.05 showed an improved cathodic behavior and discharge capacity retention compared to the undoped samples in the voltage range of 3.0–4.3 V. The electrodes prepared from Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_1.95F_0.05 delivered an initial discharge capacity of 158 mAh⁻¹ g and an initial coulombic efficiency is 91.3%, and the capacity retention at the 20th cycle was 94.9%. Though the F-doped samples had lower initial capacities, they showed better cycle performances compared with F-free samples. Therefore, this is a promising material for a lithium-ion battery.     

A foam engulfment model for lost foam casting of aluminum

In lost foam casting of aluminum, pressure equilibrium between the liquid metal and the decomposing foam can produce a variety of different shapes for the metal flow front, ranging from convex to concave. In extreme cases, the flow front can become so strongly concave that small pieces of the foam pattern begin to break off inside the concave hollow of the flow front and become enveloped by the advancing liquid metal. When this happens, the entire mechanism of foam decomposition changes from steady ablation to a more chaotic motion in which the metal seems to “chew” its way through the pattern, creating large bubbles of vaporizing polymer liquid in its wake. These bubbles usually lead to undesirable anomalies in the final casting. In most cases, the nonlinear equations that govern the shape of the flow front depend on a single nondimensional number, which relates the onset of the engulfing motion to specific material, geometric, and process parameters. Numerical solutions to these equations are obtained for several special cases. These solutions help to explain a number of experimental observations that until now have been poorly understood.