动态不确定多输入多输出系统的变结构鲁棒控制

本文仅利用输入输出数据给出了一种动态不确定多输入多输出系统的变结构控制器设计机制，控制系统的设计中引入了一个严格正实的模型．应用适当逻辑切换的状态变量滤波器实现变结构控制．证明了所提方案能保证全局输出有界稳定并能实现滑模控制和渐近跟踪参考模型的输出．该设计方案对结构不确定性具有一定的鲁棒性．仿真结果表明了所提方案的有效性．     

离散事件动态系统的代数模型及其控制器的分析计算

本文在离散事件动态系统的Ｐｅｔｒｉ网图形描述的基础上建立了相应的代数模型，该模型可以用来计算无竞争无回路Ｐｅｔｒｉ网的“最大状态”；该“最大状态”的计算在本文给出的动态反馈控制器中得到了应用。     

Ni对球墨铸铁热处理的影响

采用电子探针，图象分析仪、差质变分析仪和Ｘ射线衍仪定量研究了Ｎｉ在球铁中的分布和Ｎｉ铸态球铁组成相比例奥氏体中含碳量以及贝氏体转变ＴＴＴ曲线线的影响，结果表明，Ｎｉ在球铁中呈连续负偏析，其加入可以影响球铁组成上比例，并使粤氏体中含碳量和贝氏体转变孕育期期增加。     

CAD^2B—一个计算机辅助数据库设计系统

本文介绍了一个用Ｔｕｒｂｏ Ｃ语言在ＡＳＴ－２８６机器上实现的计算机辅助数据库设计系统ＣＡＤ＾２Ｂ。该系统提供了人机交互的环境，供设计者进行概念模型设计，并自动完成从概念模型逻辑模型的映射，创建满足规范化要求的关系表。该系统采用的概念模型是引入了事件和时间的扩展了的实体关系模型。该模型既能充分反映应用环境的静态和动态语义，又是向关系模式转化的基础。     

CAD OF MILLIMETER WAVE OSCILLATORS WITH THE FDHB TECHNIQUE

In this paper the modelling, analysis and optimization of millimeter wave oscillatorsare investigated by using the a frequency-domain harmonic balance technique (FDHB), where theexternal-circuit impedances looking outside from the active device are calculated with a combinedtechnique of modes expansion, Galerkin, and collocation methods. The optimization results arein agreement with the experimental ones, which show the reliability of the presented model andoptimization.     

一种新的基于极大似然估计的系统辨识方法

进化计算是一种基于自然选择和自然变异机制的并行随机优化算法。由于递推极大似然估计法难以实现性能指标函数的全局寻优，所以本文提出了将改进的进化计算用于系统参数辨识的方法。计算机仿真结果表明，该算法能够实现似然函数的全局寻优。     

Scattering parameters of a waveguide cross junction loaded with a metallic post in the center

In this paper, the scattering parameters of a waveguide cross junction loaded with a metallic post in the center are analyzed for the first time by using the Method of Lines. The homogeneous boundary condition of the third kind and curved boundary are introduced in the formulation. Numerical results are in good agreement with the experimental data. The scattering parameters at Ka-band and W-band of the cross junctions loaded with metallic posts of different radii are presented. It is shown from the numerical results that loaded with metallic posts is an effective means for adjusting the network parameters of the waveguide cross junction to satisfy some special requirements in the design of millimeter wave components.     

MMR: A MultiMedia Router architecture to support hybrid workloads

During the past few years, multimedia traffic with quality of service (QoS) requirements has become of widespread use. Media servers are usually built as clusters of workstations connected by a high-performance interconnection network. However, these high-performance networks do not usually offer differentiated support for multimedia traffic. The MultiMedia Router (MMR) is a proposal to address the QoS issue in cluster networks within a compact architecture, while also integrating conventional best-effort traffic. This paper describes the main architectural features of the MMR, such as the use of a hybrid switching technique, credit-based flow control, or small input buffers. Also, the main design parameters are tuned by means of simulation. It can be seen how proper differentiation among the different traffic classes is achieved, while retaining a compact design with small buffers.     

长螺旋水下灌注桩技术及其经济性探讨

阐述了长螺旋水下灌注桩的技术要点及技术参数控制标准,结合工程实例中桩基检测的结果,分析表明,采用长螺旋水下灌注桩技术施工便捷、噪声小、效率高、成本低,是一种经济、高效、环保的施工工艺.     

圆形槽波导波长计的研究¹

圆形槽波导与高Q谐振腔相耦合可以用作毫米波波长计，本文应用网络分析和等效电路的方法对圆形槽波导波长计中的耦合结构进行了理论分析和计算。