Enhanced transduction coefficient in piezoelectric PZT ceramics by mixing powders calcined at different temperatures

Large transduction coefficient ($d_{33}\times g_{33}$) is difficult to obtain in piezoelectric ceramics because these two parameters show opposite trends with compositional modifications. Herein, the Pb(Zr_0.53Ti_0.47)O₃ ceramic powders were calcinated under different temperatures (A:830 °C, B:860 °C, and C:890 °C), and then mixed together according to different weight ratios (1A:1B:1C, 1A:2B:1C, 1A:2B:3C and 3A:2B:1C) for ceramics preparation. Both d₃₃ and g₃₃ are improved successfully, and the transduction coefficient with the weight ratio of 1A:2B:3C reaches up to 17,500 × 10⁻¹⁵ m²/N, which is 60 % higher than that with the powders calcinated under 830 °C, and at least twice those of commercial PZT-4, PZT-5A and PZT-8 ceramics. The improved transduction coefficient is owing to the enhanced piezoelectric constant and spontaneous polarization resulted from the increased grain size, relative density and the fraction of tetragonal phase. These results indicate that this is a simple but effective way to tailor the transduction coefficient in piezoelectric ceramics.     

NaFeTiO4: A novel visible light active photocatalyst for water splitting and environmental remediation

Single phase, crystalline NaFeTiO₄ with tunnel structure is prepared by a solid state method and explored as a novel photocatalyst for the first time. Structural, optical and morphological properties of NaFeTiO₄ are investigated by various characterization techniques such as X-ray diffraction (XRD), scanning & transmission electron microscopy (SEM & TEM), Energy dispersive X-ray spectroscopy (EDS), N₂ adsorption-desorption study (BET), UV-vis, X-ray photoelectron, X-ray absorption (UV-vis DRS, XPS and XANES) and photoluminescence (PL) spectroscopy. The interfacial charge transfer ability of the prepared n-type NaFeTiO₄ was also investigated by transient photocurrent response and electrochemical impedence spectroscopy which proved to be an efficient tool for better understanding of electronic properties of NaFeTiO₄. The photocatalytic efficiency of NaFeTiO₄ is evaluated for decomposition of methylene blue (MB) and Rhodamine B (RhB) dyes as well as for H₂ evolution through water splitting reaction under visible light. NaFeTiO₄ exhibits efficient charge separation properties, excellent photocatalytic activities and reusability.     

重力坝模型的尺寸效应

利用两个不同比尺预制缝重力坝模型的试验成果，以有限元富集技术进行非线性断裂分析，建立了极限承载力和长度比尺的确定性尺寸效应公式。混凝土重力坝的断裂尺寸效应满足指数衰减关系，用三次指数衰减公式可以准确地预测原型的极限承载力。断裂过程区的相对长度是引起模型试验尺寸效应的主要原因。数值计算结果表明，断裂过程区相对长度不仅是与材料有关的参数，能否充分发展还取决于结构尺寸和几何形状；断裂过程区相对长度的尺寸效应不同于统计尺寸效应和断裂参数尺寸效应，具有尺寸范围效应。断裂过程区相对长度在小试件、大试件和相对无穷大试件的发展程度不同。     

基于投影寻踪的径向基函数网络在参考腾发量预测中的应用

径向基函数网络(RBFN)已广泛应用于参考腾发量预测等领域，但常用的K均值聚类和自组织特征映射等方法在求取径向基函数网络隐层节点中心时存在较大不足。针对这一问题，本文引入投影寻踪方法，在投影降维的基础上实现对大量高维数据的聚类，建立了基于投影寻踪的径向基函数网络模型，并将该模型应用于山西潇河灌区参考腾发量的预测，研究了不同气象因子输入对参考腾发量预测精度的影响。结果表明，基于投影寻踪的径向基函数网络具有较强的适用性，只需使用最高温度、最低温度、日照时数和旬序数作为输入因子，就能以较高的精度预测参考腾发量。     

An inventory analysis of rural pollution loads in China.

Rural pollution has attracted increasing attention over the past decade for its important consequences on surface and groundwater quality. This is particularly so in China due to the wide and effective control of industrial and municipal wastewater discharges over the past decade. Based on the discussion of rural activities in China, this paper develops a new method of inventory analysis through the definition of elementary unit (EU). This inventory analysis approach is then applied to estimate the total rural pollution loads of COD, TN and TP, as well as their spatial distributions in China. Further analysis is also conducted to investigate the correlations between rural pollution loads and agricultural production outputs, as well as population. It is found that China's agriculture is developing largely at the cost of environment quality, and a high population, as well as the increasing demand for agricultural products, is one of the dominant driving forces. The constructed EKC, which describes the relationship between rural pollution loads and agricultural income, also reveals that current agricultural development in China is mostly far from de-locked from the environmental problem.     

结构振动试验转接器的设计及安装问题

一些产品及其相关部件在作振动试验时，由于产品的外形或特殊要求不能直接安装在振动台面上，需要通过特别设计的转接器（夹具）来进行连接，这种夹具实际上是一种附加结构，它作为台面与试件之间的中介，如设置不当将影响振动试验结果的可靠性。本文通过对某事例的分析与研究，从试验频带、允许误差、跟随条件以及安装共振频率等方面阐明与讨论了相关夹具的特性、设计原则与安装等问题。     

一种基于Normal基椭圆曲线密码芯片的设计

文章设计了一款椭圆曲线密码芯片。实现了GF（2^233）域上normal基椭圆曲线数字签名和认证。并支持椭圆曲线参数的用户配置。在VLSI的实现上，提出了一种新的可支持GF（2^233）域和GF（p）域并行运算的normal基椭圆曲线VLSI架构。其架构解决了以往GF（p）CA算迟后于GF（2^233）域运算的问题，从而提高了整个芯片的运算吞吐率。基于SMIC 0．18μm最坏的工艺，综合后关键路径最大时延3．8ns，面积18mm^2；考虑布局布线的影响，芯片的典型的情况下，每秒可实现8000次签名或4500次认证。     

Thermo-Sensitive Ba0.64Sr0.36TiO3 Thin Film Capacitors for Dielectric Type Uncooled Infrared Sensors

Ba_0.64Sr_0.36TiO₃ (BST) thin films are prepared on Pt/Ti/SiO₂/Si₃N₄/SiO₂/Si substrates by a sol-gel method. Thermo-sensitive BST thin film capacitors with a Metal-Ferroelectrics-Metal (M-F(BST)-M) structure are fabricated as the active elements of dielectric type uncooled infrared sensors. XRD are employed to analyze the crystallographic structures of the films. AFM observations reveal a smooth and dense surface of the films with an average grain size of about 35 nm. Rapid temperature annealing (RTA) process is a very efficient way to improve crystallization quality. The preferable annealing temperature is 800°C for 1 min. The butterfly shaped C-V curves of the capacitors indicate the films have a ferroelectric nature. The dielectric constant and dielectric loss of the films at 100 kHz are 450 and 0.038, respectively. At 25°C, where the thermo-sensitive capacitors work, the temperature coefficient of dielectric constant (TCD) is about 5.9 %/°C. These results indicate that the capacitors with sol-gel derived BST thin films are promising to develop dielectric type uncooled infrared sensors.     

EBSP study of the annealing behavior of aluminum deformed by equal channel angular processing

Commercial purity aluminum (99.5%) was fabricated by equal channel angular pressing (ECAP) up to total accumulated strains of approx. 10. The annealing behavior of material deformed to total strains of approx. 1 and 10 was investigated, using heat treatments of 2 h at various temperatures from 100 to 500 °C. The microstructure of the annealed materials was characterized using the electron back-scatter pattern technique. A number of parameters were determined including the distribution and average values of both the boundary spacings and misorientations. For samples deformed to a total strain of 1, annealing resulted in discontinuous recrystallization. For samples deformed to a total strain of 10, annealing resulted in microstructures exhibiting characteristics of both uniform coarsening and, in a number of places, of discontinuous recrystallization. An attempt was made, based on the boundary spacing distributions, to separate these two components. The grain size after annealing was still however small, being just 6.4 μm after 2 h at 300 °C.