Mechanical and thermal properties of polyvinylchloride/olive residue flour blends treated by gamma irradiation

In this study, gamma irradiation treatments were used to improve the compatibility between poly(vinyl chloride) (PVC) and olive residue flour (ORF). The blends were subjected to gamma irradiation at doses of 10 and 70 kGy. The mechanical, thermal, and morphological behaviors of those blends have been assessed. The irradiated blends exhibit better thermal properties, higher tensile modulus, elongation, and strength at break than those of unirradiated blends. The contact angle of water on the surface of a blend irradiated at doses of 10 and 70 kGy is smaller than that for their corresponding unirradiated blend. These treatments cause surface oxidation of PVC/ORF films, as revealed by Fourier transform infrared (FTIR) spectroscopy analysis. J. VINYL ADDIT. TECHNOL., 22:273–278, 2016. © 2014 Society of Plastics Engineers     

Packed‐bed reactor for short time gas phase olefin polymerization: Heat transfer study and reactor optimization

A specially conceived packed‐bed stopped flow minireactor (3 mL) suitable for short gas phase catalytic reactions has been used to study the start‐up of ethylene homopolymerization with a supported metallocene catalyst. Focus has been put on the heat transfer characteristics of the supported catalysts and on understanding the relationship between the initial rate and the relative gas/particle velocities and the influence of particle parameters in the packed bed. We performed a comprehensive study on the influence of various physical parameters on the heat transfer regime at start up conditions. The catalyst activity as well as the polymer morphology is shown to be dependent on heat transfer regime. The knowledge thus obtained is applicable to industrial problems like catalyst injection in fluidized beds and helps preventing experimental artifacts due to overheating in following studies. © 2011 American Institute of Chemical Engineers AIChE J, 2012     

Effect of shear stress extrusion intensity on plasticized corn flour structure: Proteins role and distribution

Plasticized corn flour‐based materials were prepared by extrusion and injection molding. Extrusion of corn flour blends (75% wet basis (wb)—glycerol (5 or 10% wb)—water) was performed in a twin‐screw extruder with either one or three shearing zones. Native corn flour is mainly composed of corn starch granules surrounded by proteins layers. Therefore, the destructuration of corn flour by thermomechanical treatments was analyzed (i) by techniques essentially allowing to monitor corn starch amorphization (differential scanning calorimetry, X‐ray diffractometry, determination of water sorption isotherms, susceptibility to hydrolysis by amylolytic enzymes) (ii) and via proteins layers role and distribution observed by confocal scanning laser microscopy and comparing the susceptibility of corn starch to hydrolysis by amylolytic enzymes in the presence or not of a protease. Both corn starch granules amorphization and proteins dispersion and aggregation were more pronounced for materials extruded in a screw profile with three shearing zones. For materials extruded in a screw profile with one shearing zone, the amorphization of starch was higher in materials made with 5% wb glycerol, whereas the proteins dispersion and aggregation was more pronounced in materials made with 10% wb glycerol. A barrier role of proteins to hydrolysis of corn starch by amylolytic enzymes was demonstrated and discussed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Lipid Emulsions Differentially Affect LPS-Induced Acute Monocytes Inflammation: In Vitro Effects on Membrane Remodeling and Cell Viability

The aim of this study was to assess how lipid emulsions for parenteral nutrition affect lipopolysaccharide (LPS)‐induced acute monocyte inflammation in vitro. An 18 h long LPS induced human monocyte leukemia cell stimulation was performed and the cell‐growth medium was supplemented with three different industrial lipid emulsions: Intralipid^®, containing long‐chain triglycerides (LCT—soybean oil); Medialipid^®, containing LCT (soybean oil) and medium‐chain triglycerides (MCT—coconut oil); and SMOFlipid^®, containing LCT, MCT, omega‐9 and ‐3 (soybean, coconut, olive and fish oils). Cell viability and apoptosis were assessed by Trypan blue exclusion and flow cytometry respectively. Monocyte composition and membrane remodeling were studied using gas chromatography and NR12S staining. Microparticles released in supernatant were measured by prothrombinase assay. After LPS challenge, both cellular necrosis and apoptosis were increased (threefold and twofold respectively) and microparticle release was enhanced (sevenfold) after supplementation with Medialipid^® compared to Intralipid^®, SMOFlipid^® and monocytes in the standard medium. The monocytes differentially incorporated fatty acids after lipid emulsion challenge. Finally, lipid‐treated cells displayed microparticles characterized by disrupted membrane lipid order, reflecting lipid remodeling of the parental cell plasma membrane. Our data suggest that lipid emulsions differentially alter cell viability, monocyte composition and thereby microparticle release. While MCT have deleterious effects, we have shown that parenteral nutrition emulsion containing LCT or LCT and MCT associated to n‐3 and n‐9 fatty acids have no effect on endotoxin‐induced cell death and inflammation.     

Spark plasma sintering microscopic mechanisms of metallic systems: Experiments and simulations

The microscopic densification mechanisms of metallic systems (TiAl, Ag-Zn) by spark plasma sintering (SPS) have been studied by simulations and experiments. Finite element simulations showed that, despite very high current densities at the necks between metallic powder particles (≈5 × 10⁴ A/cm²), only very limited Joule overheating can be expected at these locations (<1°C), because of very fast heat diffusion. The microscopic plasticity mechanisms under these high electric currents have been studied by transmission electron microscopy. For this purpose, thin foils have been extracted by focused ion beam at the necks between TiAl powder particles. This is the first time, to the best of our knowledge, that microscopic plasticity mechanisms at the necks between powder particles are investigated by TEM during densification of a metallic powder. Dislocation glide and climb mechanisms were identified, followed by recovery and recrystallization. The elementary mechanism kinetically controlling these phenomena is proposed to be bulk diffusion of Al, which activation energy (360 kJ/mol) is close to the activation energy measured for densification (308 ± 20 kJ/mol). Comparisons of densification kinetics by SPS (≈60-110 A/cm²) and by hot pressing (0 A/cm²) showed no influence of current on these mechanisms. Finally, reaction experiments in the Ag-Zn system did not show any influence of very high currents (>1000 A/cm²) on diffusion kinetics. Consequently, densification by SPS occurs by classical mechanisms not affected by the current.     

Quaternary ammonium‐functionalized polymers in biodegradable matrices: Physicochemical properties,morphology, and biodegradability

Quaternary ammonium‐functionalized polymers (QAFPs) based on branched structures of poly(lactic acid) (PLA) and polycaprolactone (PCL) were blended with neat matrices of PLA and PCL to improve their processability in the melt phase at 160 °C. Different formulations were prepared by varying the proportions of the components of the blends (0, 10, 20, 50, and 60 wt % of QAFP). The rheological behavior of each component and their blends was studied at 160 °C and dynamic mechanical analyses were carried out. The thermal properties of the matrices were also investigated by thermogravimetric analyses and differential scanning calorimetry; they were found to be affected by the presence of QAFPs within them. All the studied blends had a dispersed morphology, highlighted by scanning electron microscopy. The water contact angle of the blends was studied and showed that the hydrophilicity of the surfaces of the blends increased by increasing their QAFP content. The biodegradability of both the components and the blends was investigated: a decrease of the biodegradation kinetics was observed due to the presence of the quaternary ammonium groups, but the materials remain biodegradable. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45261.     

Effects of the Surface Densities of Glycoclusters on the Determination of Their IC50 and Kd Value Determination by Using a Microarray

Pseudomonas aeruginosa (PA) is an opportunistic bacterium involved in 10–30 % of nosocomial diseases. It causes severe lung injury to cystic fibrosis patients, often leading to patient death. PA strains are multidrug resistant, thus making the design of new therapeutics a challenge for public health. One promising therapeutic option is to design glycoclusters that target the virulence factor of PA. LecA is a galactose‐specific lectin that might be involved in adhesion and biofilm formation by PA. The DNA‐directed immobilization (DDI) microarray is a powerful tool for screening and understanding of structure–activity relationships between glycoclusters and lectins. High‐throughput and multiplexed analysis of lectin–glycocluster interactions on a DDI microarray allows measurement of IC₅₀ and dissociation constant (K_d) values with minute amounts of material. In order to study the robustness of the DDI microarray in determination of IC₅₀ and K_d values, the impact of glycocluster surface density was investigated. The data obtained show that measured IC₅₀ values were influenced by glycocluster surface density: as the density of glycoclusters increases, the measured IC₅₀ values increase too. In contrast, the measured K_d values were not affected by glycocluster surface density, provided that the experimental conditions allow interaction between glycocluster and lectin at single‐molecule level (no surface cluster effect).     

HYDRAULIC PREFERENCES OF SHRIMPS AND FISHES IN TROPICAL INSULAR RIVERS

Hydraulic habitat models based on the preferences of species for the hydraulic characteristics of their microhabitats are frequently used to evaluate the impact on the habitat of a change in river flow regime. Their application in a tropical insular environment is still limited as little is known about the hydraulic preferences of species. Hydraulic preference models have been developed for 15 taxa (diadromous shrimps and fishes) sampled in 52 rivers in the Caribbean (the French West Indies) and the Indian Ocean (the Reunion island). Five datasets were used and group 8353 samples collected by electrofishing during 320 surveys (reach × date) performed between 1999 and 2011. Generalized additive models were used to link variations of taxa density within surveys to the hydraulic characteristics of the microhabitat (velocity, depth and substrate). Hydraulic preferences within each region (Caribbean and Indian Ocean) are significant for most of the taxa and vary little between rivers and surveys. The hydraulic variables explain up to 18.1% (univariate models) and 30.0% (multivariate models) of the deviance of densities within survey. Of the taxa selected, Atya scabra, Macrobrachium heterochirus, Xiphocaris elongata and the Sicydiinae are the most demanding. Copyright © 2013 John Wiley & Sons, Ltd.     

BichiCAM,an Underwater Automated Video Tracking System for the Study of Migratory Dynamics of Benthic Diadromous Species in Streams

Conventional methods for surveying diadromous fish migration from marine coastal waters to freshwater habitats are mainly based on electrofishing, a non‐optimal technique for the study of fish migrations in rivers, and fishermen catch data. Underwater video has been recognized for a long time as a good alternative, but those approaches usually require intensive labour for retrieving the information from the video sequences. To overcome these problems, an underwater video system specifically designed for field work (low‐weight, low‐cost and autonomous) named BichiCAM has been developed for automatically counting, measuring and tracking fish observed in video sequences. The efficiency and precision of the BichiCAM system were tested by filming Sicyopterus lagocephalus juveniles passing through the camera field of vision in the Saint‐Etienne River, Reunion Island, Western Indian Ocean. The BichiCAM system accurately measured fish length of the observed individuals when lens distortion of the camera was corrected, and the error percentages on the measurements presented a standard deviation of 5.1% of the total length. The BichiCAM system provides a powerful tool that will not only facilitate research on migrating fishes and invertebrates' communities but also allow studies of the effectiveness of fishways associated to dams or the impacts of fishery activities. Copyright © 2015 John Wiley & Sons, Ltd.