Erosion resistance of CO2 corrosion scales formed on API P110 carbon steel

The erosion resistance of CO₂ corrosion scales formed on carbon steel was investigated in water–sand two-phase flow utilizing weight loss test, scanning electron microscopy, and X-ray diffraction. The effects of CO₂ partial pressure, stirring speed, test time, and grain size on the erosion resistance of the scales were analysed. Results show that several characteristics of CO₂ corrosion scales are key factors affecting erosion resistance. Cubic polynomials are used to fit the erosion rate data, and effectively evaluate the ability of CO₂ corrosion scales to resist erosion. An erosion mechanism, based on fluid dynamics and CO₂ corrosion scales characteristics, is discussed.     

Metallic glass–steel composite with improved compressive plasticity

A Zr_52.5Cu₁₈Ni_14.5Al₁₀Ti₅ bulk metallic glass toughened with a commercially available spring-shaped steel wire has been produced by centrifugal casting. The addition of the steel spring significantly affects shear band nucleation and propagation through the blockage, deflection and multiplication of shear bands at the glass–spring interface. As a result of the more homogeneous distribution of the plastic strain, the room temperature plasticity increases from 0.9% for the monolitic glass to about 4% for the glass–spring composite. Given the low volume fraction of the spring used in the composite (4.2 vol.%), these results demonstrate the extreme effectiveness of the steel spring for improving the plasticity of the metallic glass.     

A research on the creep properties of titanium matrix composites rolled with different deformation degrees

(TiB + La₂O₃)/Ti composites were in situ synthesized and deformed with different deformation degrees. The influence of TiB whisker orientation and grain refinement on the creep properties of titanium matrix composites (TMCs) are discussed. The creep test reveals that the steady state creep rate of TMCs first decreases and then increases with the increase of deformation degree, which can be attributed to competing effects: TiB whisker rotating to the rolling direction, α plate grain boundary hindering and pinning dislocations can all decrease the creep rate, however, dislocation movement on the α plate grain boundary and dislocation emitting from the α plate grain boundary can both increase the creep rate.     

Influence of temperature on the pitting corrosion behavior of AISI 316L in chloride–CO2 (sat.) solutions

The paper discusses the pitting corrosion behavior of AISI (American iron and steel institute) 316L stainless steel in aerated chloride solutions (0.1–2 M NaCl) at 25, 50 and 80 °C using potentiodynamic polarization technique. A comparison is made with CO₂-saturated chloride solutions. The results have revealed that pitting potential decreased in a logarithmic relationship with the chloride concentration, and decreased linearly with temperature. The influence of CO₂ on the chloride pitting of AISI 316L stainless steel is quite complex and found to be dependent on chloride concentration and test temperature. At 25 °C the presence of CO₂ appears to have insignificant effect on E_p irrespective of chloride concentration. As the temperature is raised to 50 or 80 °C the additions of CO₂ has caused marked negative shifts in pitting potential. The detrimental effect of CO₂ increases with NaCl concentration and temperature. The results indicate that pitting potential (E_p) is influenced by a synergy between chloride, CO₂ and temperature, and that this synergy depends on the chloride concentration and test temperature.     

Crystal nucleation and dendrite growth of metastable phases in undercooled melts

An undercooled melt possesses an enhanced free enthalpy that opens up the possibility to crystallize metastable crystalline solids in competition with their stable counterparts. Crystal nucleation selects the crystallographic phase whereas the growth dynamics controls microstructure evolution. We apply containerless processing techniques such as electromagnetic and electrostatic levitation to containerlesss undercool and solidify metallic melts. Owing to the complete avoidance of heterogeneous nucleation on container-walls a large undercooling range becomes accessible with the extra benefit that the freely suspended drop is direct accessible for in situ observation of crystallization far away from equilibrium. Results of investigations of maximum undercoolability on pure zirconium are presented showing the limit of maximum undercoolability set by the onset of homogeneous nucleation. Rapid dendrite growth is measured as a function of undercooling by a high-speed camera and analysed within extended theories of non-equilibrium solidification. In such both supersaturated solid solutions and disordered superlattice structure of intermetallics are formed at high growth velocities. A sharp interface theory of dendrite growth is capable to describe the non-equilibrium solidification phenomena during rapid crystallization of deeply undercooled melts. Eventually, anomalous growth behaviour of Al-rich Al–Ni alloys is presented, which may be caused by forced convection.     

Gold extraction by chlorination using a pyrometallurgical process

The feasibility to recover the gold present in alluvial material, by means of a chlorination process, using chlorine as a reactive agent, has been studied. The influence of temperature and reaction time was studied through changes in the reactant solid. The techniques used to characterize the mineral samples and the reaction residues were stereomicroscopy, X-ray diffraction, X-ray fluorescence and scanning electronic microscopy. Results indicate that gold extraction is favored by increasing, both, the temperature and the reaction time. The best recovery values were of 98.23% at 873 K and 3600 s and of 98.73% at 873 K and 5400 s, with very low attack of the matrix containing the metal. The powder of pure gold was not chlorinated at this temperature level.     

Microstructural evolution,flow stress and constitutive modeling of Al−1.88Mg−0.18Sc−0.084Er alloy during hot compression

To explore the hot compression behavior and microstructural evolution, fine-grained Al?1.88Mg?0.18Sc? 0.084Er (wt.%) aluminum alloy wires were fabricated with Castex (continuous casting?extrusion) and ECAP-Conform, and their hot compression behavior was investigated at temperatures of 673?793 K and strain rates of 0.001?10 s^?1; the microstructures were characterized by optical microscope, X-ray diffractometer, transmission electron microscope, and electron backscattered diffractometer, and the flow stresses were obtained by thermal compression simulator. Microstructural evolution and flow curves reveal that dynamic recovery is the dominant softening mechanism. Continuous dynamic recrystallization followed by dynamic grain growth takes place at a temperature of 773 K and a strain rate of 0.001 s^?1; the yielding drop phenomenon was discovered. Hyperbolic sine constitutive equation incorporating dislocation variables was presented, and a power law constitutive equation was established. The stress exponent is 3.262, and the activation energy for deformation is 154.465 kJ/mol, indicating that dislocation viscous glide is the dominant deformation mechanism.     

低碳钢表面激光熔覆不锈钢的组织和性能

采用JHM-1GY-400型脉冲Nb∶YAG固体激光器和316L不锈钢粉末在20低碳钢表面制备了激光熔覆层。利用OM、XRD、SEM等表征方法分析了不锈钢熔覆层的物相组成和显微组织,并分别利用旋转摩擦试验机和电化学工作站对熔覆层和基材的耐磨损和耐腐蚀性进行了研究。试验结果表明,不锈钢熔覆层厚度约为50 μm,由γ相(奥氏体)和α相(铁素体)组成,其显微组织主要包括细小的树枝晶、粗大的胞状晶以及平面晶;不锈钢熔覆层表面硬度约为基材的2倍,摩擦因数比基材低0.0418,磨损量更低,不锈钢熔覆层比基材具有更高的耐磨性。与基材相比,不锈钢熔覆层具有更低的自腐蚀电流和更高的自腐蚀电位,其耐腐蚀性能更优异。     

Alkaline aluminum phosphate glasses for thermal ion-exchanged optical waveguide

Alkaline aluminum phosphate glasses (NMAP) with excellent chemical durability for thermal ion-exchanged optical waveguide have been designed and investigated. The transition temperature Tg (470 °C) is higher than the ion-exchange temperature (390 °C), which is favorable to sustain the stability of the glass structure for planar waveguide fabrication. The effective diffusion coefficient D_e of K⁺–Na⁺ ion exchange in NMAP glasses is 0.110 μm²/min, indicating that ion exchange can be achieved efficiently in the optical glasses. Single-mode channel waveguide has been fabricated on Er³⁺/Yb³⁺ doped NMAP glass substrate by standard micro-fabrication and K⁺–Na⁺ ion exchange. The mode field diameter is 9.6 μm in the horizontal direction and 6.0 μm in the vertical direction, respectively, indicating an excellent overlap with a standard single-mode fiber. Judd–Ofelt intensity parameter Ω₂ is 5.47 × 10⁻²⁰ cm², implying a strong asymmetrical and covalent environment around Er³⁺ in the optical glasses. The full width at half maximum and maximum stimulated emission cross section of the ⁴I_13/2 → ⁴I_15/2 are 30 nm and 6.80 × 10⁻²¹ cm², respectively, demonstrating that the phosphate glasses are potential glass candidates in developing compact optoelectronic devices. Pr³⁺, Tm³⁺ and Ho³⁺ doped NMAP glasses are promising candidates to fabricate waveguide amplifiers and lasers operating at special telecommunication windows.     

Microstructure,mechanical and corrosion properties of friction stir welded high nitrogen nickel-free austenitic stainless steel

Friction stir welding (FSW) was applied to a 2.4 mm thick high nitrogen nickel-free austenitic stainless steel plate using tungsten–rhenium (W–Re) tool. The high-quality weld was successfully produced at a tool rotational speed of 400 rpm and a traveling speed of 100 mm/min. The microstructure, mechanical and corrosion properties of the weld were studied. The nitrogen content of the weld was almost identical to that of base metal (BM). FSW refined grains in the stir zone (SZ) through dynamic recrystallization and led to increase in hardness and tensile strength within the SZ, while the ductility was slightly decreased. The failure of tensile specimens occurred in the BM. TEM results revealed precipitates of Cr₂₃C₆ of size ~ 1 μm in the SZ, although their content was small. The precipitation of Cr₂₃C₆ and increase in δ-ferrite in the SZ led to small decrease in both pitting and intergranular corrosion resistance.