Biomimetic synthesis of spherical nano-hydroxyapatite in the presence of polyethylene glycol

Spherical nano-hydroxyapatite (nano-HA) was synthesized successfully by a biomimetic method using Ca(NO₃)₂·4H₂O and (NH₄)₃PO₄·3H₂O as reagents in the presence of polyethylene glycol (PEG). The crystalline phase, microstructure, chemical composition, and morphology of the obtained samples were characterized by X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and transmission electron microscopy (TEM). The results show that spherical nano-HA with diameter of 30–50 nm can be synthesized in the presence of a certain concentration (2–6%) of PEG. The crystallinity of HA powder synthesized in the presence of PEG was higher than that synthesized in the absence of PEG, but the crystallinity of HA reduced with increasing the concentration of PEG. The electrical conductivity (EC) of the solution revealed that PEG reduced the transfer rate of Ca²⁺ in the process of HA crystallization, indicating the interaction between PEG and HA. The possible mechanism of formation spherical nano-HA was discussed.     

Green and self-lubricating polyoxymethylene composites filled with low-density polyethylene and rice husk flour

Polyoxymethylene (POM) composites filled with low-density polyethylene (LDPE) and rice husk flour (RHF) were prepared by injection molding. The POM/5 wt % LDPE/7.5 wt % RHF composite exhibited the lowest wear rate, whereas the coefficient of friction remained low, and the POM/5 wt % LDPE/5 wt % RHF composite had the best mechanical properties. X-ray diffraction analysis was carried out, and the worn surfaces were examined with scanning electron microscopy. The results showed that the addition of the filler reduced the crystallinity degree of the POM composites. The main wear mechanism for unfilled POM was adhesion, whereas for the POM composites, wear seemed to occur mainly by fatigue and abrasion. It was experimentally confirmed that the POM composite filled with LDPE and RHF, which is well-performing, low-cost, and environmentally friendly, could be a potential material for tribological applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis,characterization, and redox and electrochromic behaviors of poly(3-n-octyloxythiophene)

Poly(3-n-octyloxythiophene), a conjugated polymer, which possessed solubility in common organic solvents, was synthesized by electrochemical polymerization in the presence of lithium perchlorate as the supporting electrolyte and sodium dodecyl sulfate as the surfactant in an aqueous medium. Characterizations of the intermediate, monomer, and polymer were performed by NMR spectroscopy, Fourier transform infrared spectroscopy, ultraviolet–visible spectroscopy, and gel permeation chromatography. The process of electrochemical polymerization and the electrochemical redox behaviors were investigated by cyclic voltammetry and the potentiostatic method. A poly(3-n-octyloxythiophene) film that was deposited on a platinum electrode was found to exhibit electrochromic behaviors, and it switched electrochemically between blue–green oxidized and dark red reduced states. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

A study on dynamic friction of different spun yarns

This article presents the results from a study of yarn-to-yarn (YY) and yarn-to-metal (YM) frictions conducted on ring, rotor, air-jet, and open-end friction (OE friction) spun yarns at different relative speeds and input tensions. The results indicate that the behavior of frictions for YY is different than that of YM. In case of YY friction, OE friction yarn shows maximum friction followed by rotor, air-jet, and ring spun yarns; however, a reverse order is noticed for YM friction. The relative speed and input tension have significant influence on the frictional behavior of spun yarns. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Microstructure and mechanical behaviour of semi-solid die-casting AZ91D magnesium alloy

Microstructures and mechanical properties of an AZ91D magnesium alloy prepared with semi-solid die-casting (SSDC) were characterized in as-cast conditions. The SSDC alloy exhibits a unique microstructure featuring primary α-Mg globules uniformly distributed in the matrix of fine secondary α-Mg grains and β-Mg₁₇Al₁₂ intermetallic. High ultimate tensile strength and elongation have been achieved before fracture. Observations on the vertical-section microstructure of the fractured sample by scanning electron microscopy (SEM) show that the crack mainly originated from the brittle fracture of the eutectic phase causes the interface decohesion of the ductile Mg phase, making fracture a rather critical event. Before that, the deformation of ductile α-Mg phase in the matrix as well as the “pulling out” of primary α-Mg phase combines to provide the SSDC alloy a certain strain.     

Syntheses and structural properties of four Rb-aluminosilicate zeolites

Four types of Rb-aluminosilicate zeolites were hydrothermally synthesized in pure phase for the first time from Rb-aluminosilicate gels without using any organic structure-directing agent (SDA) under stirring conditions. The crystal structure of each zeolite was refined by Rietveld analysis of the X-ray diffraction (XRD) data. These crystal structures were confirmed to be Rb-mordenite, Rb-merlinoite, a new aluminosilicate zeolite with an ATT framework topology, and Rb-offretite denoted by RMA-1, RMA-2, RMA-3, and RMA-4, respectively. The Si/Al ratio of RMA-1 with an MOR topology varied from 5.3 to 8.0; however, the variation of the Si/Al ratios of the other zeolites was rather small. The crystal system of RMA-2 was tetragonal with space group I4/mmm, where two Rb sites were distributed at the center of an 8-membered ring (MR). On the other hand, two Rb sites in RMA-3 were located at the center of the 8-MR in small two cages. The structure of RMA-4 was identified as the OFF type with a local disorder or defect, which included a small amount of an intergrown ERI phase.     

Wrinkling of corrugated skin sandwich panels

Compression wrinkling of composite sandwich panels with corrugated skins was investigated numerically, analytically and experimentally. Semi-circular and sine-wave shaped corrugations were studied. The corrugations significantly increased wrinkling strength when compared with equal mass flat panels. Semi-circular corrugations proved to be highly preferable to sine-wave shaped corrugations due to localized buckling in the latter. Over 40 fiberglass and foam core sandwich specimens were manufactured with semi-circular skin corrugations. These specimens were tested to failure, providing confirmation of the numerical and analytical results.     

Thermoelastic evaluation of composite laminates using digital imaging processing

The study of the variation of the curvature of non-symmetric composite laminates with temperature provides a measure of the magnitude of the thermal stresses and the mechanical behavior of the material with temperature. In the present work, an experimental method based on the pioneer use of a digital camera and image processing method is proposed to perform such measurements. Taking advantage of the method and by comparing experimental and CLT, extended-CLT and FEM simulation results, an evaluation of the residual stresses is described and an approach providing more precise determination of the residual thermal stresses in non-symmetric laminates is proposed.     

Minimum weight design of inhomogeneous rotating discs

There are numerous applications for gas turbine discs in the aerospace industry such as in turbojet engines. These discs normally work under high temperatures while subjected to high angular velocities. Minimizing the weight of such items in aerospace applications results in benefits such as low dead weights and lower costs. High speed of rotation causes large centrifugal forces in a disc and simultaneous application of high temperatures reduces disc material strength. Thus, the latter effects tend to increase deformations of the disc under the applied loads. In order to obtain a reliable disc analysis and arrive at the corresponding correct stress distribution, solutions should consider changes in material properties due to the temperature field throughout the disc. To achieve this goal, an inhomogeneous disc model with variable thickness is considered. Using the variable material properties method, stresses are obtained for the disc under rotation and a steady temperature field. In this paper this is done by modelling the rotating disc as a series of rings of different but constant properties. The optimum disc profile is arrived at by sequentially proportioning the thicknesses of each ring to satisfy the stress requirements. This method vis-à-vis a mathematical programming procedure for optimization shows several advantages. Firstly, it is simple iterative proportioning in each design cycle not requiring involved mathematical operations. Secondly, due to its simplicity it alleviates the necessity of certain simplifications that are common in so-called rigorous mathematical procedures. The results obtained, compared to those published in the literature show agreement and superiority. A further advantage of the proposed method is the independence of the end results from the initially assumed point in the iterative design routine, unlike most methods published so far.     

Diffusion-controlled growth in ternary systems

Diffusion-controlled growth of particles, dendrites, and plates in infinite media is examined for ternary systems. The growth kinetics associated with planar, cylindrical, and spherical particles are shown to be limiting cases of a more complete analysis (also presented) for shape-preserving growth. The theory is applied to the growth of allotriomorphic ferrite from austenite in ternary Fe-C-X steels, where X represents a substitutional alloying element. Numerical results are given, the analysis relying on the ability to predict multicomponent phase equilibria. The work represents an attempt at coupling together thermodynamic and kinetic models for the diffusion-controlled3 phase transformations that occur in steels.