Generalized difference control of parallel streams temperatures

A furnace with multiple parallel passes and multiple burners is commonly seen in petroleum refineries. In order to maintain the furnace running in a safe, stable, and high-efficiency state it is necessary to control the outlet temperatures of the multiple passes to be the same. Due to the fact that the process of the oil heating in such furnace is nonlinear, multivariable, time varying, has serious coupling among passes, has frequent dynamic changes and a large time delay, traditional control methods have trouble in controlling these temperatures, and some advanced control methods, including predictive control, adaptive control, and robust control, are usually too complex for convenient use. In this paper, a control technique, called differences control technique (DsCT), is proposed to distribute the stream flowrates such that the stream temperatures are as identical as possible. The principle of the proposed technique is explained and demonstrated, and the results of its application to a real-life petroleum refinery furnace are also reported. The DsCT technique has the following advantages: it does not need complicated design procedures, the controller structure is simple, it is easy to apply, and it can be canonically applied to furnaces with different number of passes.     

Peracetic acid pretreatment of sugarcane bagasse for enzymatic hydrolysis: a continued work

Previous work has shown that the enzymatic hydrolysis of sugarcane bagasse could be greatly enhanced by peracetic acid (PAA) pretreatment. There are several factors affecting the enzymatic digestibility of the biomass, including lignin and hemicelluloses content, cellulose crystallinity, acetyl group content, accessible surface area and so on. The objective of this work is to analyze the mechanism of the enhancement of enzymatic digestibility caused by PAA pretreatment. Delignification resulted in an increase of the surface area and reduction of the irreversible absorption of cellulase, which helped to increase the enzymatic digestibility. The Fourier transform infrared (FTIR) spectrum showed that the absorption peaks of aromatic skeletal vibrations were weakened or disappeared after PAA pretreatment. However, the infrared crystallization index (N.O'KI) was increased. X‐ray diffraction (XRD) analysis indicated that the crystallinity of PAA‐treated samples was increased owing to the partial removal of amorphous lignin and hemicelluloses and probable physical change of cellulose. The effect of acetyl group content on enzymatic digestibility is negligible compared with the degree of delignification and crystallinity. The results indicate that enhancement of enzymatic digestibility of sugarcane bagasse by PAA pretreatment is achieved mainly by delignification and an increase in the surface area and exposure of cellulose fibers. Copyright © 2008 Society of Chemical Industry     

A new method for distributing power usage across a sensor network

We present a method for more uniformly distributing the energy burden across a wireless ground-based sensor network communicating with an overhead unmanned aerial vehicle (UAV). A subset of sensor nodes, termed a transmit cluster, receives and aggregates data gathered by the entire network, and forms a distributed antenna array, concentrating the radiated transmission into a narrow beam aimed towards the UAV. Because these duties are power-intensive, the role of transmit cluster must be shifted to different nodes as time progresses. We present an algorithm to reassign the transmit cluster, specifying the time that should elapse between reassignments and the number of hops that should be placed between successive transmit clusters in order to achieve three competing goals: first, we wish to better and more broadly spread the energy load across the sensor network while, second, minimizing the energy expended in moving the transmit cluster, all the while, third, reducing to the extent practicable the time to bring the UAV and the sensor network’s beam into alignment. Additionally, we present a method for reconfiguring the communication burden between the ground-based sensor network and the UAV. We describe and analyze two alternative strategies to bring the UAV and the sensor network’s beam into alignment, while minimizing the energy expended by the sensor network. The performance of the two strategies is compared in terms of probability of beam-UAV alignment as a function of time, and the expected time to alignment. We examine the performance tradeoff between the choice of strategy and parameters of the sensor network that affect power conservation.     

Synthesis and properties of cinnamic acid series organic UV ray absorbents–interleaved layered double hydroxides

Organic ultraviolet (UV) ray absorbents, cinnamic acid (CA) and p-methoxycinnamic acid (PMOCA) were intercalated into Zn₂Al layered double hydroxides (Zn₂Al-LDHs) by co-precipitation reaction. The organic–inorganic nanocomposites, Zn₂Al-LDH/CA and Zn₂Al-LDH/PMOCA were obtained. The samples showed excellent UV ray absorption ability and their catalytic activity for the air oxidation of castor oil greatly decreased when the organic UV ray absorbents were intercalated in the layers of the Zn₂Al-LDHs. The studies suggested that Zn₂Al-LDH/organic UV absorbent nanocomposites might be used as safe sunscreen materials.     

Behaviors of concrete-filled steel tubular members subjected to combined loading

The present study is an investigation on the behaviors of concrete-filled thin-walled steel tubular members subjected to combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. ABAQUS software is used in this paper for the finite element analysis (FEA). A comparison of results calculated using this modeling shows generally good agreement with test results. The FEA modeling is then used to investigate the influence of important parameters that determine the ultimate strength of the composite members under combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. The parametric studies provide information for the development of formulae for calculating the ultimate strength of the composite members subjected to combined loading.     

Grain refinement of Al-7Si alloys and the efficiency assessment by recognition of cooling curves

Under sand cup solidification condition, the influence of Ti, B concentration, and holding time on the grain size of a high-purity Al-7Si alloy has been systematically studied. It is found that the grain size decreases rapidly at lower Ti or B additions, and is almost constant at the higher concentrations. For Al-3B refined Al-7Si alloys, the grain size increases at the initial period of holding time, and then rapidly becomes independent of holding time; while for Al-7Si alloys refined with Al-5Ti-1B, the grain size increases with holding time throughout. To evaluate the refinement efficiency, a new method named “intelligent evaluating of melt quality by pattern recognition of thermal analysis cooling curves” has also been introduced in this article. The results show that comparing the cooling curve of the evaluated melt with those in a database to find the most similar one to it can precisely assess the grain refinement efficiency of the measured Al-7Si alloy. In addition, the influence of Ti, B addition levels, and pouring temperatures on some characteristic parameters of cooling curve has also been discussed.     

Tracking-error model-based predictive control for mobile robots in real time

In this paper, a model-predictive trajectory-tracking control applied to a mobile robot is presented. Linearized tracking-error dynamics is used to predict future system behavior and a control law is derived from a quadratic cost function penalizing the system tracking error and the control effort. Experimental results on a real mobile robot are presented and a comparison of the control obtained with that of a time-varying state-feedback controller is given. The proposed controller includes velocity and acceleration constraints to prevent the mobile robot from slipping and a Smith predictor is used to compensate for the vision-system dead-time. Some ideas for future work are also discussed.     

A new way for constructing high accuracy shock-capturing generalized compact difference schemes

The generalized compact (GC) schemes and some of their important properties are presented. And a new way for constructing high order accuracy and high-resolution GC schemes is presented. The schemes constructed by using this way could satisfy some principles and demands prescribed in advance to ensure some desired properties to the schemes, such as the principle about suppression of the oscillations, the principle of stability, the order of accuracy and number of scheme points, etc. As two examples, a three-point third-order compact scheme and a three-point fifth-order GC scheme satisfying the principle about suppression of the oscillations and the principle of stability are described in this paper. Numerical results show that these schemes are shock-capturing. The time-dependent boundary conditions proposed by Thompson are well employed when the algorithm is applied to the Euler equations of gas dynamics. Fourier analysis shows that the resolution characteristics are spectral-like.     

Effect of dual-scale microstructure on the toughness of laminar zirconia composites

Numerical study by the finite element method (FEM) is performed to investigate the effect of dual-scale microstructure on the toughness of laminar zirconia composite. The computation is based on the micromechanics constitutive model of polycrystal transformation plasticity developed by Sun et al. [10] where both transformation induced shear and softening effects during autocatalytic transformation are taken into account. The numerical simulation presented in this paper successfully reproduced the experimentally observed two effects of the dual-scale microstructure on the toughness of laminar zirconia composite, i.e., the truncation of the elongated transformation frontal zone that forms in single phase Ce-ZrO₂ and the propagation of the transformation zone along the layers normal to the crack plane. Quantitative analysis on the role of microstructure in transformation toughening of laminar zirconia composite is first carried out in the present work which will provide a starting point for the microstructural design of this novel advanced composite in the future.Presented at the Far East Fracture Group (FEFG) International Symposium on Fracture and Strength of Solids. 4–7 July 1994 in Xi'an, China.