Research on wind turbine blade damage based on pre-stressed FBG strain sensors

One of the essential parts of a wind power generator that captures wind energy is the wind turbine blade. The safety of the blades rapidly declines as a wind turbine''s operating period grows. For real-time monitoring, a chip-type pre-stressed fiber Bragg grating (FBG) strain sensor was fabricated. The sensor''s structure was improved using simulation analysis along with optimization. It was discovered through calibration trials that the pre-stressing method expanded the sensor''s range of measurement, guaranteed overall linearity, and prevented the potential hysteresis phenomena during compression. The sensor''s final sensitivity was calculated to be 1.970 pm/με, and its linear fitting coefficient was 0.999. Finally, the sensor was used to monitor the wind turbine blades and the strain change curve of the root of a normally functioning blade is found to be a sine curve, which provides a certain reference value for judging whether the blade is damaged in the future.     

Improved DV-Hop based on parallel and compact whale optimization algorithm for localization in wireless sensor networks

Wireless Networks - Improving localization performance is one of the critical issues in Wireless Sensor Networks (WSN). As a range-free localization algorithm, Distance Vector-Hop(DV-Hop) is...     

基于爬虫的XSS漏洞检测工具设计与实现

通过对XSS漏洞的研究,剖析其产生、利用的方式,在此基础上针对XSS漏洞的检测机制进行进一步的分析和完善。结合网络爬虫的技术,研究设计并实现了一款XSS漏洞的检测工具（XSS-Scan）,并与当前比较流行的一些软件做了分析比较,证明利用该工具可以对Web网站进行安全审计,检测其是否存在XSS漏洞。     

Analysis of DWTT property of thick X70 pipeline steel

The microstructures of X70 pipeline steels with different thickness specifications and different rolling reduction ratios were analyzed by metallographic microscope, scanning electron microscope, and electron backscatter diffraction techniques, and the original austenite microstructures were compared. The effect of compression ratio on the original austenite structure was studied. The results show that the large compression ratio in the rolling process is more conducive to refine austenite grains and improve the low- temperature toughness of thick X70 pipeline steel. However, due to the fact that the temperature during the finish rolling process is too low to permeate the center of the deformation, it is necessary to further use the low- temperature stage of the rough rolling process to perform deformation infiltration. Ultra- rapid cold cooling after rolling can improve the DWTT performance of the steel, but it is not sufficient to compensate for the fluctuation of DWTT performance caused by insufficient early austenite grain refinement.     

家政O2O发展现状分析

随着国内家政行业进阶为万亿级市场,家政业务交易额每年增幅都超过20％.家政O2O作为大众期望的一种运营模式,刚好能迎合这样快速发展的家政市场.首先介绍了国内家政服务市场的现状,然后分析了家政O2O的发展基础,最后以95081的家政O2O模式为例,分析了国内家政O2O的出路.     

Determination of flow stress and the critical strain for the onset of dynamic recrystallization using a hyperbolic tangent function

A new model has been developed to estimate the flow stress under hot deformation conditions up to the peak of the stress–strain curves. This model is derived from the general form of hyperbolic function by introducing an additional parameter to bring the results to a more acceptable level. Stress–strain curves and the critical strain of a ‘304 austenitic stainless steel’ are determined with an average percentage error of 1.24. The model is also used to obtain an equation which has the ability of predicting the critical strain for the onset of dynamic recrystallization.     

气密型化学防护服研究进展

针对当前国内外危险化学品事故灾害频发、生化恐怖袭击威胁日益严峻、防化装备研发及生产体系不健全,国内个体化学防护装备特别是气密型化学防护服的材料研发、结构设计、装备生产、性能检测及选择使用亟待规范等问题,梳理了国际标准、美国消防协会标准、欧洲标准及中国国家标准中涉及气密型化学防护服的产品分类及性能要求,介绍了国内外气密型化学防护服市场上主流产品的防护性能、结构特征、产品认证情况及其发展现状,对比分析了化学防护领域广泛应用的防护材料种类及性能。研究表明:尽管目前采用高分子膜制作化学防护面料的国内厂商较少,但部分面料的防护能力已经能够同时达到国家标准、国际标准和欧洲标准的要求;建议相关行政管理部门继续给予化学防护行业必要的政策扶持,以尽快实现高性能化学防护装备的国产化、规模化及体系化。     

基础偏位不稳定条件下大跨度钢桁架结构滑移支座纠偏吊装施工技术

结合宁德火车站站台雨棚桩基础出现偏位且处于不稳定状态情况以及工程工期紧迫的现实要求,提出了滑移支座施工方案。介绍了滑移支座纠偏吊装施工工艺、操作要点及质量安全控制措施。结合工程应用实际对技术经济效益及社会效益进行了分析。     

形变组织对水电用高强度贝氏体钢再加热奥氏体晶粒长大的影响

对某水电用800 MPa调质贝氏体高强钢进行了热变形-热处理晶粒长大的实验室联合试验。采用Gleeble-3500热力模拟试验机对钢试样进行不同工艺热压缩变形后冷却至室温,随后对试样进行模拟淬火再加热,在900～1200℃不同温度和保温时间条件下奥氏体化,研究热变形组织的差异对重新奥氏体化晶粒长大的影响规律。结果表明,不同应变速率(0.01～10 s^-1)、变形温度(900～1150℃)和60%工程应变下,试验钢获得的变形组织大致可分为3类：带有明显变形特征的组织、均匀细小的完全再结晶组织和已长大粗化的再结晶组织。3类组织再加热过程中其晶粒长大趋势基本相同,起始晶粒尺寸越大则最终奥氏体晶粒尺寸越大;但在950℃等温时,带有明显变形特征组织的变形试样奥氏体晶粒先缓慢长大后又迅速长大粗化。经评估验证,所建立的Sellars模型、Beck模型和Hillert模型晶粒长大动力学方程对于试验钢的奥氏体晶粒长大行为均有比较满意的预测效果。3类变形组织对应的Hillert模型及Sellars模型中奥氏体长大激活能基本相同,说明同一成分钢种的初始组织的差异并未显著影响晶粒长大机制...     

退火工艺路径对980 MPa级高强钢组织及性能的影响

为了提升980 MPa级高强钢局部成形性能,采用万能试验机、场发射扫描电镜(SEM)、电子背散射衍射(EBSD)及综合成形试验机等研究了不同退火工艺路径的980 MPa高强钢微观组织和力学性能,并评价了其扩孔及局部成形性能。结果表明,除了有铁素体和马氏体两相外,新型Q&T工艺的组织结构还存在回火马氏体中间相,铁素体和马氏体平均晶粒尺寸分别为3.14μm和2.62μm,马氏体面积分数为61.0%,而传统工艺下为典型的铁素体及马氏体双相组织,铁素体和马氏体平均晶粒尺寸分别为4.77μm和2.77μm,马氏体面积分数为35.8%。两种工艺伸长率相差不大,但屈服强度和扩孔率具有明显差异,新型Q&T工艺下获得了更高的屈强比及扩孔性能,得益于其更小铁素体晶粒尺寸及铁素体和马氏体硬度差。传统工艺下真实断裂应变(TFS)与真实均匀应变ε_u比值为7.0,而新型Q&T工艺下比值为15.2,因此新型Q&T工艺下具有更优异的局部成形特性。