Applicability and toxicity evaluation of an adsorbent based on jujube for the removal of toxic heavy metals

The removal of heavy metals from industrial wastewater is important, owing to its eco-toxicity in aqueous environment. In this study, the mechanism and efficiency of the removal of toxic heavy metals by an eco-friendly adsorbent was investigated. Various types of adsorbents made from jujube were synthesized by varying the drying temperature of gel-type beads and elution method for jujube constituents. The maximum adsorption capacity for lead and copper ions was determined using the Langmuir isotherm model, with DJB-A-S-F (freeze-dried jujube bead made from a solution of squeezed autoclaved jujube) having the highest values at 60.44 mg/g (lead) and 20.33 mg/g (copper). In addition, the characteristics of the various adsorbents were determined by the Brunauer–Emmett–Teller (BET) method, scanning electron microscopy (SEM), and energy dispersive X-ray analysis (EDX). Gas chromatography–mass spectrometry (GC–MS) was used to identify the constituents of DJB-A-S-F before and after adsorption of heavy metals (Pb- and Cu-DJB-A-S-F). Furthermore, in vitro cytotoxicity assay was performed to investigate whether the binding of heavy metals to DJB-A-S-F increases cellular toxicity. As a result, no differences in cell viability between DJB-A-S-F and the ones coupled to heavy metals were observed, indicating that the developed adsorbents are non-cytotoxic with good compatibility. Thus, DJB-A-S-F is a promising adsorbent for the removal of toxic heavy metal cations from wastewater.     

Impact assessment of reservoir desiltation measures for downstream riverbed migration in climate change: A case study in northern Taiwan

Typhoon Aere in 2004 induced severe sedimentation and loss of storage capacity of the Shihmen Reservoir in northern Taiwan. The resulting dramatic increase in the turbidity of the water seriously affected the water supply. To effectively maintain the stability of the water supply and maintain the reservoir’s storage capacity, the government of Taiwan began to plan and construct a series of improvement measures, such as a sediment flushing tunnel, the JhongJhuang Bank-Side Reservoir, and the Amuping Desilting Tunnel. However, previous studies only focused on the impact of the sediment flushing tunnel and the Amuping Desilting Tunnel on the downstream riverbed, and did not consider the possibility of increasing sediment discharge after the completion of the JhongJhuang Bank-Side Reservoir. In addition, climate change will cause the intensity of extreme rainfall to increase enormously in the future. That rainfall and extra sediment flushing will challenge the existing flood prevention facilities. Therefore, this study considered that the JhongJhuang Bank-Side Reservoir will increase sediment discharge of the Shihmen Reservoir, and used dynamical downscaling extreme typhoon data of climate change under the RCP 8.5 scenario to explore the flood prevention and riverbed migration of the main channels of the Dahan and Tamsui Rivers in the future. We used the rainfall–runoff model of Hydrologic Modeling System to simulate rainfall and runoff, and used the hydraulic and sediment transport model of CCHE1D to holistically simulate flood events and consequent river scouring and deposition behaviors. Our results showed that the projected peak discharge during the late 21st century (2075 to 2099) will be at least 50% higher than that during the baseline (1979 to 2003) period. In terms of flood prevention, the potential of overbank flooding will increase in the downstream area, and the trend of long-term change in the riverbed will be dominated by degradation (-0.489 ± 0.743 m) in the future. The improvement measures will have a limited impact on riverbed migration (0.011 ± 0.094 m) in the Dahan and Tamsui Rivers. After the operation of the JhongJhuang Bank-Side Reservoir, the Shihmen Reservoir is expected to increase the sediment discharge ratio by 70% during floods, and it will not cause excessive water turbidity that may affect downstream water supply.     

A zirconium-free glaze system for sanitary ceramics with SiO2-CaCO3-TiO2 composite opacifier containing anatase: Effect of interface combination among SiO2, CaCO3 and TiO2

TiO₂ is an ideal substitute to ZrSiO₄ ceramic opacifier, yet it is limited to application because of the undesirable yellowing resulting from rutile formation. Herein, the SiO₂-CaCO₃-TiO₂ composite opacifier (Si-Ca-Ti) was constructed. The glaze used Si-Ca-Ti presents a superior opacification performance than ZrSiO₄ opacified glaze without causing yellowing, showing L*, a*, b* values of 94.81, -0.67 and 3.23. By comparison, the glaze using SiO₂, CaCO₃, and TiO₂ mixture shows lower opacification and yellowish surface with L* and b* values of 92.99 and 5.36. It is revealed that there is a close interface bonding among SiO₂, CaCO₃ and TiO₂ in Si-Ca-Ti, which promotes their combination reaction to generate opacification phase titanite and inhibit rutile formation when sintering, resulting in the white surface and opacification improvement of the glaze. This study proposes a green and efficient strategy to achieve white and highly opacified glaze for sanitary ceramics, exhibiting good application prospect.     

Improving the multi-objective evolutionary optimization algorithm for hydropower reservoir operations in the California Oroville–Thermalito complex

This study demonstrates the application of an improved Evolutionary optimization Algorithm (EA), titled Multi-Objective Complex Evolution Global Optimization Method with Principal Component Analysis and Crowding Distance Operator (MOSPD), for the hydropower reservoir operation of the Oroville–Thermalito Complex (OTC) – a crucial head-water resource for the California State Water Project (SWP). In the OTC's water-hydropower joint management study, the nonlinearity of hydropower generation and the reservoir's water elevation–storage relationship are explicitly formulated by polynomial function in order to closely match realistic situations and reduce linearization approximation errors. Comparison among different curve-fitting methods is conducted to understand the impact of the simplification of reservoir topography. In the optimization algorithm development, techniques of crowding distance and principal component analysis are implemented to improve the diversity and convergence of the optimal solutions towards and along the Pareto optimal set in the objective space. A comparative evaluation among the new algorithm MOSPD, the original Multi-Objective Complex Evolution Global Optimization Method (MOCOM), the Multi-Objective Differential Evolution method (MODE), the Multi-Objective Genetic Algorithm (MOGA), the Multi-Objective Simulated Annealing approach (MOSA), and the Multi-Objective Particle Swarm Optimization scheme (MOPSO) is conducted using the benchmark functions. The results show that best the MOSPD algorithm demonstrated the best and most consistent performance when compared with other algorithms on the test problems. The newly developed algorithm (MOSPD) is further applied to the OTC reservoir releasing problem during the snow melting season in 1998 (wet year), 2000 (normal year) and 2001 (dry year), in which the more spreading and converged non-dominated solutions of MOSPD provide decision makers with better operational alternatives for effectively and efficiently managing the OTC reservoirs in response to the different climates, especially drought, which has become more and more severe and frequent in California.     

Enhancing cation exchange capacity of chars through ozonation

The use of ozone to increase the cation exchange capacity (CEC) of two chars produced from pyrolysis of Douglas fir (Pseudotsuga menziessii) and a control bituminous coal activated carbon (AC) is reported. Chars were produced from the wood fraction of Douglas fir (DFWC) and the bark (DFBC) at 500 °C using an auger driven reactor with a nitrogen sweep gas under mild vacuum. Five ozone treatment times, ranging from 5 min to 60 min, were investigated. The initial properties of each char were found to differ significantly from the other samples in terms of surface area, proximate composition, and elemental composition. DFWC did not show significant mass loss or temperature variation during ozone treatment; however, after 1 h of oxidation both DFBC and AC samples resulted in 20% and 30% mass loss, respectively, and reactor temperatures in excess of 60 °C. Analysis of the pore size distribution of each treatment shows that ozone treatment did not significantly affect small micropores after 30 min of treatment for any material, but did reduce the apparent surface area of mesopores. Increases in carboxylic groups were identified with ozone treatment and found to correlate strongly with changes in measured CEC. The formation of lactone was found to correlate positively with reactor temperature during oxidation. These results indicate that the properties of chars, including surface area, pore structure, and chemical composition, as well as reactor conditions strongly affect the ozone oxidation of chars.     

Nickel foam-supported Fe,Ni-Polyporphyrin microparticles: Efficient bifunctional catalysts for overall water splitting in alkaline media

Developing highly active, stable and sustainable electrocatalysts for overall water splitting is of great importance to generate renewable H₂ for fuel cells. Herein, we report the synthesis of electrocatalytically active, nickel foam-supported, spherical core-shell Fe-poly(tetraphenylporphyrin)/Ni-poly(tetraphenylporphyrin) microparticles (FeTPP@NiTPP/NF). We also show that FeTPP@NiTPP/NF exhibits efficient bifunctional electrocatalytic properties toward both the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER). Electrochemical tests in KOH solution (1 M) reveal that FeTPP@NiTPP/NF electrocatalyzes the OER with 100 mA cm⁻² at an overpotential of 302 mV and the HER with 10 mA cm⁻² at an overpotential of 170 mV. Notably also, its catalytic performance for OER is better than that of RuO₂, the benchmark OER catalyst. Although its catalytic activity for HER is slightly lower than that of Pt/C (the benchmark HER electrocatalyst), it shows greater stability than the latter during the reaction. The material also exhibits electrocatalytic activity for overall water splitting reaction at a current density of 10 mA cm⁻² with a cell voltage of 1.58 V, along with a good recovery property. Additionally, the work demonstrates a new synthetic strategy to an efficient, noble metal-free-coordinated covalent organic framework (COF)-based, bifunctional electrocatalyst for water splitting.     

Comparative evaluation of the mesophilic and thermophilic biohydrogen production at optimized conditions using tequila vinasses as substrate

The objective of this work was to comparatively evaluate the production of biohydrogen (bio-H₂) from tequila vinasses at optimized mesophilic and thermophilic conditions and to elucidate the main metabolic routes involved. Optimal temperatures of 35 °C and 55 °C, and pH of 5.5 maximized the bio-H₂ production rates, 25.5 ± 0.01 NmL h⁻¹ and 169.9 ± 8.9 NmL h⁻¹ in the mesophilic and thermophilic regimens, respectively. During the operation of anaerobic sequencing batch reactors, the thermophilic process allowed a volumetric bio-H₂ production rate of 519 ± 13 NmL-H₂ L⁻¹ d⁻¹ equivalent to 750 ± 19 NmL-H₂ L_vinasse⁻¹, while the mesophilic one 448 ± 23 NmL-H₂ L⁻¹ d⁻¹ and 647 ± 33 NmL-H₂ L_vinasse⁻¹, respectively. Furthermore, the gas produced under thermophilic conditions showed high hydrogen content (86.5%). Finally, formate degradation and glucose fermentation to acetic and butyric acids were the main metabolic routes involved in bio-H₂ production under thermophilic conditions, while at mesophilic conditions, the lactate and formate degradation pathways governed.     

Effect of microbial hydrogen consumption on the hydrogen permeation behaviour of AISI 4135 steel under cathodic protection

The feasibility of microbial hydrogen consumption to mitigate the hydrogen embrittlement (HE) under different cathodic potentials was evaluated using the Devanathan-Stachurski electrochemical test and the hydrogen permeation efficiency η. The hydrogen permeation efficiency η in the presence of strain GA-1 was lower than that in sterile medium. The cathodic potential inhibited the adherence of strain GA-1 to AISI 4135 steel surface, thereby reducing the hydrogen consumption of strain GA-1. The adherent GA-1 cells were capable of consuming ‘cathodic hydrogen’ and reducing the proportions of absorbed hydrogen, indicating that it is theoretically possible to control HE by hydrogen-consuming microbes.     

Alkali catalyzed liquefaction of corncob in supercritical ethanol–water

Corncob liquefaction in supercritical ethanol–water was performed with and without the addition of an alkali catalyst by direct addition or biomass impregnation in a 250-cm³ batch reactor. The effects of temperature, solvent and alkali addition on the biomass conversion level and oil yield were investigated to find the optimum condition. For non-catalytic liquefaction using a 1:1 (v/v) ethanol: water ratio, a maximum oil yield and conversion level of 49.0% and 93.4%, respectively, were obtained at 340 °C. For alkali catalytic liquefaction, the oil yield with KOH addition (57.5%) was higher than that from KOH-impregnated corncob liquefaction (43.3%). The oil from liquefaction with KOH addition had higher heating value (26.7–35.3 MJ kg⁻¹) than the corncob (19.1 MJ kg⁻¹). The dominant components of the obtained oil were found by GC/MS analysis to be aldehyde, ester, phenol derivatives and aromatic compounds.