Densification mechanism during reactive hot pressing of B4C-ZrO2 mixtures

The densification behaviors of pure B₄C and B₄C-ZrO₂ mixtures were compared during hot pressing. The results showed that in-situ formed ZrB₂ effectively enhanced the densification process of B₄C-ZrO₂ mixtures, more significantly during the intermediate stage. Within the relative density ranging from 0.75 to 0.90, the B₄C-15?wt%ZrO₂ mixture (B15Z) achieved the maximum densification rate as twice much as that of pure B₄C. The stress exponent n>3 indicated plastic deformation was the dominant densification mechanism of B15Z. The viscosities of plastic flow were evaluated using Murray-Rodger-William equation and the viscosity of B15Z was only a quarter of that in pure B₄C. The sintering activation energy was calculated to be 305.9?kJ/mol for pure B₄C and 197?kJ/mol for B15Z, respectively. It was proposed that the lower viscosity of plastic flow and activation energy accelerated the sliding and propagating motions of plastic flow, by which underlain the enhanced densification behaviors of B₄C-ZrO₂ mixtures.     

Synthesis,lattice energy and microwave dielectric properties of BaCu2-xCoxSi2O7 ceramics

BaCu_2-xCo_xSi₂O₇ solid solutions with orthorhombic structure (Pnma) were prepared by solid-state reaction method. The phase synthesis process, structural evolution and microwave dielectric properties of BaCu_2-xCo_xSi₂O₇ ceramics were investigated. Single BaCu₂Si₂O₇ phase was obtained when calcined at 950 °C for 3 h and was decomposed into BaCuSi₂O₆ phase when calcined at 1075 °C for 3 h. The sintering process was effectively promoted when Cu²⁺ was replaced by Co²⁺ and the maximum solubility of BaCu_2-xCo_xSi₂O₇ was located between 0.15 and 0.20. P-V-L complex chemical bond theory and Raman spectra were used to explain the structure-property correlations of BaCu_2-xCo_xSi₂O₇ ceramics. The corrected dielectric constant (ε_r-corr) of BaCu_2-xCo_xSi₂O₇ ceramics decreased monotonously with the susceptibility (Σχ^μ) and ionic polarizability of primitive unit cell. The quality factor (Q × f) increased with bond strength and lattice energy (U_cal), especially the lattice energy of the Si-O bond. The temperature coefficient of resonant frequency (τ_f) was determined by the susceptibility and lattice energy of the Cu/Co-O bond. The following optimum microwave dielectric properties were obtained at x = 0.15 when sintered at 1000 °C for 3 h: ε_r = 8.45, Q×f =58958 GHz and τ_f = -34.4 ppm/°C.     

Enhanced graphitic domains of unreduced graphene oxide and the interplay of hydration behaviour and catalytic activity

Previous studies indicate that the properties of graphene oxide (GO) can be significantly improved by enhancing its graphitic domain size through thermal diffusion and clustering of functional groups. Remarkably, this transition takes place below the decomposition temperature of the functional groups and thus allows fine tuning of graphitic domains without compromising with the functionality of GO. By studying the transformation of GO under mild thermal treatment, we directly observe this size enhancement of graphitic domains from originally ≤40 nm² to >200 nm² through an extensive transmission electron microscopy (TEM) study. Additionally, we confirm the integrity of the functional groups during this process by a comprehensive chemical analysis. A closer look into the process confirms the theoretical predicted relevance for the room temperature stability of GO and the development of the composition of functional groups is explained with reaction pathways from theoretical calculations. We further investigate the influence of enlarged graphitic domains on the hydration behaviour of GO and the catalytic performance of single atom catalysts supported by GO. Additionally, we show that the sheet resistance of GO is reduced by several orders of magnitude during the mild thermal annealing process.     

Neutral axis depth and moment redistribution in FRP and steel reinforced concrete continuous beams

The neutral axis depth is considered the best parameter for quantifying the moment redistribution in continuous concrete beams, as exemplified in various design codes worldwide. It is therefore important to well understand the variation of neutral axis depth against moment redistribution. This paper describes a theoretical investigation into the neutral axis depth and moment redistribution in concrete beams reinforced with fibre reinforced polymer (FRP) and steel bars. A finite element model has been developed. The model predictions are in favourable agreement with experimental results. Three types of reinforcement are considered, namely, glass fibre, carbon fibre and steel. Various levels of reinforcement ratio are used for a parametric evaluation. The results indicate that FRP reinforced concrete continuous beams exhibit significantly different response characteristics regarding the moment redistribution and variation of neutral axis depth from those of steel reinforced ones. In addition, it is found that the code recommendations are generally unsafe for calculating the permissible moment redistribution in FRP reinforced concrete beams, but the neglect of redistribution in such beams may be overconservative.     

Improving performance of high-power indium gallium nitride/gallium nitride-based vertical light-emitting diodes by employing simple n-type electrode pattern

In this work, simple n-type electrode structures were used to enhance the electrical and optical performances of fully packaged commercially mass-produced vertical-geometry light-emitting diodes (VLEDs). The forward bias voltage of the VLED with a Y-pattern electrode increased less rapidly than that of VLEDs with a reference electrode. The VLEDs with the reference and Y-pattern electrodes exhibited forward voltages of 2.93±0.015 and 2.89±0.015 V at 350 mA and 3.77±0.015 and 3.53±0.015 V at 2000 mA, respectively. The VLEDs with the Y-pattern electrode resulted in a higher light output than the VLEDs with the reference electrode with increase in the drive current to 2000 mA. The emission images showed that the VLEDs with the Y-pattern electrode exhibited better current spreading behavior and lower junction temperatures than the VLEDs with the reference electrode. With increase in the current from 350 to 2000 mA, the VLEDs with the Y-pattern electrode experienced a 39.4% reduction in the wall plug efficiency, whereas the VLEDs with the reference electrode suffered from a 43.3% reduction.     

Producing fully-lamellar microstructure for wrought beta-gamma TiAl alloys without single α-phase field

Fine-grained fully-lamellar (FL) microstructure is desired for TiAl components to serve as compressor/turbine blades and turbocharger turbine wheels. This study deals with the process and phase transformation to produce FL microstructure for Mo stabilized beta-gamma TiAl alloys without single α-phase field. Unlike the α + γ two-phased TiAl or beta-gamma TiAl with single α-phase field, the wrought multi-phase TiAl–4/6Nb–2Mo–B/Y alloys exhibit special annealing process to obtain FL microstructure. Short-term annealing at temperatures slightly above β-transus is recommended to produce the desired FL microstructure. The related mechanism is to guarantee the sufficient diffusion homogenization of β stabilizers during single β-phase annealing, and further avoid α decomposition by α → γ + β when cooling through α + β + γ phase field. The colony boundary β phase contributes to fine-grained nearly FL microstructure, by retarding the coarsening of the α phase grains.     

Preparation and Properties of a New Mediumdensity and High-strength Ceramic Proppant

Based on the needs of the market,a new 52 MPa medium-density and high-strength ceramic proppant was prepared by adopting third grade bauxite and clay as raw materials and using the solid phase sintering method,and the effect of the firing temperature on the microstructure,phase composition and mechanical properties of the ceramic proppant was studied. The broken resistance mechanism of this ceramic proppant was also discussed. The results show that the main phases of the prepared ceramic proppant are mullite and corundum; the broken rates are 3. 92% and 7. 21% under 52 MPa and69 MPa,respectively.