Implications from γ-globulin adsorption onto cation exchangers fabricated by sequential alginate grafting and sulfonation

Our previous work proved that high adsorption capacity and uptake rate of lysozyme were achieved on alginate(Alg)-grafted re sin with an ionic capacity(IC) of 240 mmol·L~(-1)(Alg-FF-240).Moreover,the salt-tolerant feature of Alg-FF-230 was improved by using sequential alginate grafting and sulfonation strategy.Inspired by the enhanced adsorption performance of lysozyme,we have herein proposed to investigate the static and dynamic adsorption behaviors of γ-globulin on a series of Alg-grafted resins with different grafting densities and sulfonation degrees.The adsorption ca pacity of γ-globulin decreased with increa sing alginate-grafting density(IC) from 160 to 230 mmol·L~(-1) at 0 mmol·L~(-1) NaCl because of the steric hindrance caused by the alginate-grafting layer.Effects of ionic strength(IS) indicated that the adsorption capacities of the resins with the IC value of 230-370 mmol·L~(-1) were much higher than CM Sepharose FF at 50-100 mmol·L~(-1) NaCl,and the uptake rate of Alg-FF-230 was about twice as much as that of CM Sepharose FF.This work demonstrated the important effects of alginate-grafting layer and IS in γ-globulin adsorption behavior,which would be helpful in the design of Alggrafted resins and the selection of proper IS condition for protein purification.     

以CoMn2O4为催化剂氧化二甲苯的研究

探索催化剂的制备条件,包括搅拌温度、干燥温度、煅烧温度及煅烧时间对二甲苯氧化效果的影响,结果表明煅烧温度对氧化效果的影响最为明显。在其它制备条件（搅拌温度为60 ℃、干燥温度为60 ℃和煅烧时间为3 h）不变的前提下,通过改变煅烧温度（温度分别350、450和550 ℃）,比较3种二甲苯氧化难易以及不同煅烧温度下氧化同一构型二甲苯的差异。整体而言,煅烧温度为350 ℃的催化剂性能最佳。邻、间和对3种二甲苯完全氧化的温度相差约15 ℃,其中,邻二甲苯最难氧化,完全氧化需260 ℃,间二甲苯次之,对二甲苯最易氧化。与此同时,利用XRD、XPS、N₂吸附-脱附和H₂-TPR等表征手段来分析煅烧温度造成3种不同构型二甲苯氧化程度差异性的原因。     

Nickel-Carnosine complex:A new carrier for enzymes immobilization by affinity adsorption

Immobilization is an effective method to promote the application of enzyme industry for improving the stability and realizing recovery of enzyme.To some extent,the performance of immobilized enzyme depends on the choice of carrier material.Therefore,the development of new carrier materials has been one of the key issues concerned by enzyme immobilization researchers.In this work,a novel organic-inorganic hybrid material,nickel-carnosine complex (NiCar),was synthesized for the first time by solvothermal method.The obtained NiCar exhibits spherical morphology,hierarchical porosity and abun-dant unsaturated coordination nickel ions,which provide excellent anchoring sites for the immobiliza-tion of proteins.His-tagged organophosphate-degrading enzyme (OpdA) and ω-transaminase (ω-TA)were used as model enzymes to evaluate the performance of NiCar as a carrier.By a simple adsorption process,the enzyme molecules can be fixed on the particles of NiCar,and the stability and reusability are significantly improved.The analysis of protein adsorption on NiCar verified that the affinity adsorp-tion between the imidazole functional group on the protein and the unsaturated coordination nickel ions on NiCar was the main force in the immobilization process,which provided an idea way for the develop-ment of new enzyme immobilization carriers.     

Coalescence dynamics of two droplets of different viscosities in T-junction microchannel with a funnel-typed expansion chamber

The coalescence behavior of two droplets with different viscosities in the funnel-typed expansion cham-ber in T-junction microchannel was investigated experimentally and compared with droplet coalescence of the same viscosity.Four types of coalescence regimes were observed:contact non-coalescence,squeeze non-coalescence,two-droplet coalescence and pinch-off coalescence.For droplet coalescence of different viscosities,the operating range of non-coalescence becomes narrowed compared to the droplet coalescence of same viscosity,and it shrinks with increasing viscosity ratio η of two droplets,indicating that the difference in the viscosity of two droplets is conducive to coalescence,especially when 1 ＜ η＜ 6.Furthermore,the influences of viscosity ratio and droplet size on the film drainage time (Tdr) and critical capillary number (Cac) were studied systematically.It was found that the film drainage time declined with the increase of average droplet size,which abided by power-law relation with the size dif-ference and viscosity ratio of the two droplets:Tdr ～ (ld)0.25±0.04 and Tdr ～ (η)-0.1±002.For droplet coales-cence of same viscosity,the relation of critical capillary number with two-phase viscosity ratio and dimensionless droplet size is Cac =0.48λ0.26l-2.64,while for droplet coalescence of different viscosities,the scaling of critical capillary number with dimensionless average droplet size,dimensionless droplet size difference and viscosity ratio of two droplets is Cac =0.11 η-0.07ls-2.23ld0.16.     

In-situ generation of platinum nanoparticles on LaCoO3 matrix for soot oxidation

The LaCo_0.94Pt_0.06O₃ catalyst is reduced under 5% H₂/Ar at different temperatures to get Pt/LaCoO₃ with high catalytic activity for soot oxidation. Transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Brunauer–Emmett–Teller method (BET), X-ray photoelectron spectroscopy (XPS), H₂-temperature programmed reduction (H₂-TPR), O₂-temperature programmed desorption (O₂-TPD) and thermogravimetric analysis (TGA) were used to study the physicochemical properties of the catalyst. SEM and TEM results indicate that Pt nanoparticles (<10 nm) are grown homogeneously on the surface of the LaCoO₃ matrix after in-situ reduction. XRD shows that the reduced catalyst has a high symmetrical structure. TGA results indicate that all reduced catalysts exhibit an excellent activity, especially the catalyst reduced at 350 °C (T₁₀ = 338 °C, T₅₀ = 393 °C, T₉₀ = 427 °C). And perovskite is the primary active component. According to XPS study, the high symmetrical structure benefits the mobility of oxygen vacancy, and Pt nanoparticles induce the oxygen vacancy to move to its adjacent situation, resulting in more adsorbed oxygen on the surface of the reduced catalyst and increasing the activity. The possible reaction principle is also proposed.     

基于QFD质量工具集成的研究与应用

为消除产品设计制造过程中可能存在的冲突、模糊、潜在失效等因素的影响，将各种质量工具、方法与质量功能展开（QFD）进行集成研究。通过分析QFD与各种质量工具的关系，提出了一个支持产品开发的、集成的QFD系统模型，给出了产品设计与制造各阶段问题解决的方法和工具，并开发了集成的QFD软件系统（1QFDS）。通过IQFDS在起重设备的卷筒设计中的应用，表明采用集成化的QFD系统，不仅可以克服QFD所存在的缺陷，而且可优化产品的设计与制造过程。改进和提高质量水平，进而满足顾客需求。     

激光焊接齿科CoCr-NiCr异种合金组织结构研究

选用齿科烤瓷用NiCr合金和支架用CoCr合金,利用脉冲Nd-YAG激光,在不同电压下进行焊接,考察焊件力学性能,优选电压条件,研究此条件下焊件熔焊区及其附近区域化学成分、显微组织变化规律.结果表明,适合齿科临床应用焊接电压为280V,此条件下可以得到显微组织致密、细小的熔焊区,熔焊区与两侧母材呈冶金结合,主要成分为Ni元素,以固溶体和化合物形式存在;Co、Cr元素部分溶入固溶体,部分与Mo、Be形成化合物.焊接中冶金过程充分,无新相生成.双向侧吹氩气可以对熔焊区起到良好的保护作用,无氧化物形成.     

深冷处理提高镀锌钢板点焊电极寿命的机理

为了提高镀锌钢板点焊电极寿命，作者提出了镀锌钢板点焊电极的深冷处理方法。采用不同深冷处理工艺参数处理了点焊镀锌钢板的Cr—Zr—Cu合金电极，用这些电极进行了镀锌钢板点焊电极寿命试验并与未深冷处理的电极寿命进行了比较。用扫描电子显微镜对深冷处理电极进行了背散射及面扫描分析，用X射线衍射法观测了深冷处理前后的电极晶粒度，测试了电极在深冷处理前后的电阻率。通过对深冷电极微观结构的观测及电极性能的测试，探讨了深冷处理提高镀锌钢板点焊电极寿命的机理。研究结果表明，深冷处理提高了镀锌钢板点焊电极基体的致密性，改变了合金元素的分布，细化了电极材料的晶粒，提高了镀锌钢板点焊电极的导电、导热能力及电极抗压渍变形的能力，从而提高了镀锌钢板点焊电极的寿命。     

新型硬齿面环面蜗杆传动研究

采用精确磨削TI蜗杆的砂轮，用类似直廓环面蜗杆或平面包络环面蜗杆的磨削方法加工环面蜗杆，使该蜗杆和齿面形状与砂轮曲面相同的蜗轮相配合，形成一种新型蜗杆传动，给出了这种传动蜗杆副齿面的数学模型，并通过计算机仿真得出了这种传动蜗轮齿面上接触线的形状及分布特征，初步分析了其啮合特点。