Acquisition and pattern recognition of spectrum information of welding metal transfer

With the creation of a pattern recognition system for metal transfer mode, this article has collected five kinds of spectrum signals in gas metal arc welding (MIG, MAG and CO₂) and take them as training samples. These samples have been pretreated by computer, several key characteristic parameters of the spectrum signal have been creatively extracted, and a corresponding recognition function and a minimum-distance-classifier have been constructed. The results show that the pattern recognition of several kinds of metal transfer modes for the metal gas arc welding can be done successfully, and relative important parameters in welding process, such as the frequency of droplet transfer and the approximate diameter of each droplet, can also be obtained.     

应用改进BP网络对潼关高程的预测

作者在分析了影响汛前和汛后潼关高程变化值的因素的基础上，利用改进BP网络模型对非特征汛期和汛期潼关高程的变化值进行了计算。计算中不采用潼关的绝对高程，而用高程的变化量作为网络的较出物正量，从而减少计算误差，同时又能客观地考虑各影响因子的作用。改进后的BP模型学习时间短，精度满足要求。用该模型计算的潼关高程变化趋势与实际水库调度运行中的高程基本吻合。     

硫化氢吸收液的电化学分解条件研究

理想的脱硫工艺应满足体积小、费用低、净化度高、无二次污染等要求。在碱性溶液吸收微量硫化氢时同步进行电解，可有效减小设备体积，并将硫化氢转变为氢气和硫磺，不产生恶性气味。为此，实验研究了温度、浓度、电流密度、pH值等因素对电解阳极过程的影响，确定了适宜的电解条件，并在该条件下进行了吸收实验。结果表明，在最佳电解条件下，硫化钠溶液能充分吸收天然气中经变压吸附提浓的硫化氢（800 mg/m³），吸收率大于99.9％。     

铝薄膜CMP影响因素分析

提出了在碱性抛光液中铝薄膜化学机械抛光的机理模型,对抛光液的pH值、磨料、氧化剂浓度对过程参数的影响做了一些试验分析。试验结果表面粗糙度的铝薄膜所需的最优化CMP过程参数:硅溶胶粒径为15～20nm,pH值为10.8～11.2,氧化剂浓度为2.5%～3%。     

On the determination of optimal transition profile of a stepped bar in tension or in torsion by BEM

The objective is to have uniformly distributed tangential stresses on the transition profile of a stepped bar subjected to tensile and torsional loading using an axisymmetric boundary element formulation. The transition curve is represented by the Langragian interpolation polynomial with progressive degrees to avoid shape distortion during the optimization procedure. The calculated result is compared with that obtained by fluid dynamics given in the literature. It is seen that the transition curve obtained in this paper is reasonable.     

一种多晶硅高温压力传感器

制作压力传感器时，在二氧化硅层上淀积多晶硅膜，既可利用优良的机械特性，又可保证压敏电阻与衬底间具有良好的绝缘性，由此可大大提高器件的温度特性。介绍了一种多晶硅压力传感器的原理和设计。实验结果表明，这类传感器具有灵敏度好，精度高等特点，电路工作范围为０－２５０℃，且具有良好的温度稳定性。     

基于焊接温度场正面信息的熔透控制方法及验证

在所建立的试件有限尺寸三维温度场解析模型的基础上,利用相关性原理同时考虑温度变化的灵敏度问题,定量地给出了控制背面熔宽时正面测温点的选择区域,提供了测温点的一般选择原则,讨论了基于温度场正面信息的GTAW熔透控制方法,运用仿真手段进行了PID参数优化设计,通过试验验证了PID和FUZZY复合控制的有效性。     

A new type of precursor for fibers in the system Si–C

Ceramic fibers with compositions in the system Si–C have a great potential for high-temperature applications. In recent years, our efforts have been dedicated to the development of polymers consisting of polysilanes suitable to spin fibers and build up matrices for CMC as well. The polysilanes are synthesized via disproportionation of the so-called disilane fraction [Richter, R., Roewer, G., Böhme, U., Busch, K., Babonneau, F., Martin, H.-P. et al., Appl. Organomet. Chem., 1997, 11, 71 (and references cited therein)]. A further thermal treatment yields materials which are soluble in organic solvents, and these solutions can be dry-spun to give fibers which are subsequently pyrolyzed. Solubility and high ceramic yield make this precursor a promising candidate for matrix infiltrations, too. The chemistry and the adjustment of viscosity and solubility to the requirements of the fiber processing as well as the conversion of the dried fibers to pure SiC fibers by thermal treatment will be reported.     

11B and 15N solid state NMR investigation of a boron nitride preceramic polymer prepared by ammonolysis of borazine

A poly(aminoborazine), precursor for hexagonal boron nitride (h-BN) obtained by reaction of borazine B₃N₃H₆ with ammonia, and its pyrolysis derivatives have been extensively characterised by ¹⁵N and ¹¹B MAS NMR. The various B and N sites have been identified according to their first neighbouring atoms, as well as to the second ones in the case of ¹⁵N, and have also been quantified. This study demonstrates that a suitable choice of NMR techniques together with the use of isotopic enrichment can lead to a large improvement in spectral resolution, which allows a better understanding of such complex BN preceramic polymer structures and permits to follow the polymer-to-ceramic transformation.