Facile synthesis of Ti3C2 MXene-modified Bi2.15WO6 nanosheets with enhanced reactivity for photocatalytic reduction of Cr(VI)

Through a facile hydrothermal method, we have successfully prepared Ti₃C₂/Bi_2.15WO₆ (TC/BWO) composite, and systematically investigated their reactivity for the photocatalytic reduction of Cr(VI) under visible light. X-ray diffraction and Raman analysis confirm the formation of heterostructure between Bi_2.15WO₆ and Ti₃C₂. The resultant 7TC/BWO composite exhibits enhanced photoactivity toward Cr(VI) reduction. After 120 min irradiation, the conversion of Cr(VI) reaches 92.5% with the quasi-first-order kinetic constant of k = 0.0145 min^?1, which is higher than that of pure BWO (30% and k = 0.0005 min^?1). The electrochemical and photoluminescent characterization confirm that the introduction of Ti₃C₂ is conducive to the separation of carriers, thus significantly improves the photocatalytic performance of TC/BWO. Furthermore, the radical capture experiments verify that the electrons are important for enhancing reduction of Cr(VI) to Cr(III). As a result, this research provides a comprehensive understanding of the reduction of Cr(VI) by TC/BWO composite under visible light.     

基于神经网络和遗传算法的锭子弹性管性能优化

为得到减振弹性管对下锭胆的支承弹性和锭子高速运动下的稳定性等性能的最优匹配效率,依据减振弹性管的等效抗弯刚度及底部等效刚度系数公式,利用MatLab数值分析软件构建弹性管抗弯刚度和底部挠度数学模型。首先,结合Isight优化软件基于径向基神经网络构建其近似模型,且使精度达到可接受水平,并以模型的关键结构参数弹性模量、螺距、槽宽、壁厚为设计变量,结合遗传算法对弹性管抗弯刚度和底部挠度进行多目标优化设计,得到Pareto最优解集和Pareto前沿图,确定出减振弹性管结构工艺参数的优化方案。通过对优化数据进行分析发现,该方案在保证减振弹性管弹性的同时,其底部振幅明显减弱。     

Low shear rheological behaviour of two-phase mesophase pitch

The low shear rate rheology of two phase mesophase pitches derived from coal tar pitch has been investigated. Particulate quinoline insolubles (QI) stabilised the mesophase spheres against coalescence. Viscosity measurements over the range 10–10⁶ Pa s were made at appropriate temperature ranges. Increasing shear thinning behaviour was evident with increasing mesophase content. At low mesophase contents the dominant effect on the near Newtonian viscosity was temperature but at higher contents it was the shear rate; temperature dependence declined to near zero. The data indicated that agglomeration could be occurring at intermediate mesophase volume fractions, 0.2–0.3. The Krieger–Dougherty function and its emulsion analogue indicated that in this region the mesophase pitch emulsions actually behaved like ‘hard’ sphere systems and the effective volume fraction was estimated as a function of shear rate illustrating the change in extent of agglomeration. At the higher volume fractions approaching the maximum packing fraction, which could only be measured at higher temperatures, the shear thinning behaviour changed in character and it is considered that this is possibly due to shear induced deformation and breakup of dispersed drops in the shear field.     

Silver-plated polyamide fabrics with high electromagnetic shielding effectiveness performance prepared by in situ reduction of polydopamine and chemical silvering

In this article, the silver-plated polyamide fabrics (SPPAFs) with high electroconductibility and shielding effectiveness were fabricated by using in situ reduction of polydopamine and chemical silvering. The effects of SPPAFs dopamine (C₈H₁₁O₂N) and silver nitrate (AgNO₃) concentration on surface resistivity and electromagnetic interference shielding effectiveness were studied. The results showed that the surface resistivity of SPPAFs can reach a minimum value of 0.06 ± 0.014 Ω cm⁻¹, when C₈H₁₁O₂N concentration is 4 g L⁻¹ and the AgNO₃ concentration is 120 g L⁻¹. The shielding effectiveness of SPPAFs in the wide frequency range of 10–3000 MHz increases with the increase in the concentration of AgNO₃, and increases first and stabilizes afterward with increasing C₈H₁₁O₂N concentration. When the concentration of C₈H₁₁O₂N and AgNO₃ is 3 and 120 g L⁻¹, respectively, mean shielding effectiveness values in the low-, medium-, and high-frequency bands are 71.3, 73.8, and 76.1 dB, respectively. Moreover, the mean shielding effectiveness values is 83.79 dB in the frequency range of 1.2–2.3 GHz. The dominant shielding mechanism of SPPAFs is the reflected electromagnetic waves and the absorption shielding effectiveness is less than 2 dB. The average electromagnetic shielding values of SPPAFs are above 67 dB after 16 weeks of storage, when C₈H₁₁O₂N concentration is 4 g L⁻¹ and the AgNO₃ concentration is 80 and 100 g L⁻¹. The prepared SPPAFs show promising applications in military textiles and smart wearable clothing. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48227.     

Large piezoelectricity and potentially activated polarization reorientation around relaxor MPB in complex perovskite

Improving piezoelectric performance is always favorable to further enhance the sensitivity and accuracy of piezoelectric devices. Here, a complex piezoelectric system of Pb(Ni_1/3Nb_2/3)O₃-Pb(Yb_1/2Nb_1/2)O₃-Pb(Hf_0.1Ti_0.9)O₃ is designed and investigated in detail. Optimized piezoelectric response of ～ 880 pC/N is achieved at the composition of 0.51PNN-0.09PYN-0.40PHT. The characterization of TEM and In-situ high-energy synchrotron diffraction indicate that nanodomain growth and microdomain switching occurs in succession at around coercive electric field. Most interestingly, the coexisted tetragonal and rhombohedral-like phase transforms into multiple monoclinic-like phases with polarization vectors aligned as close to the electric field direction as possible under the strong electric field. The enhanced polarization instability in this complex morphotropic phase boundary sample should be ascribed to the strong local heterogeneity. The novel polarization rotation behavior found in this work would be important guidance for designing high-performance piezoceramics.     

Fabrication and properties of Si3N4 based ceramics using combustion synthesized powders

Silicon nitride (Si₃N₄) based ceramics were fabricated with β-SiAlON and Si₃N₄ powders synthesized by combustion synthesis method via power injection molding (PIM). In the PIM process, the solids loading for each material was first determined from the results of the torque rheometer experiment. The mixing process was repeated to produce the homogeneous feedstock, and homogeneity of feedstocks was evaluated by observing the shear viscosity with time at a constant shear rate. The rheological behavior of feedstocks was investigated using capillary rheometer. It found that both feedstocks have no problem in injection molding. The binder decomposition behavior was also investigated, and a wax-polymer binder system was nearly removed by the optimized solvent and thermal debinding processes. Thereafter, the debound samples were sintered at 1750 and 1800 °C for 4 h in nitrogen atmosphere. Regardless of sintering temperature, the relative density of higher than about 96% was achieved. When comparing mechanical properties including bending strength, Vickers hardness and fracture toughness, Si₃N₄ with 2 wt% Y₂O₃ and 5 wt% Al₂O₃ (Si₃N₄+2Y5A) had higher values than β-SiAlON with 4 wt% Y₂O₃ (β-SiAlON+4Y) regardless of sintering temperature. It was supported by observing the microstructures of the plasma-etched samples.     

Experimental and computational analysis for thermo-erosive stability assessment of ZrB2-SiC based multiphase composites

High temperature erosion tests were conducted on spark plasma sintered ZrB₂-SiC based multiphase ceramic composites at 1073 K in thermo-erosive environment for 1200 s with a net energy deposition per unit area of 50.5 MJ/m². The thermo-erosive mechanisms were qualitatively discussed using XRD and SEM-EDS analyses. Efforts were made to assess feasibility of identified reactions at the computed temperatures to support reaction mechanism for oxide formation in eroded region. Finite element (FE) analysis with high-quality structural elements was used to determine the spatial temperature and stress distribution in the eroded region. Taken together, the present study highlights the significance of combined approach of computational and experimental analysis in understanding the thermo-erosive-structural stability in applications where erosion can limit the performance of ceramic composites.     

Improved Repeatability of Pulsed Field Magnetometry Measurements Through Peltier Effect Temperature Control of Measurement Coils

Pulsed Field Magnetometers (PFMs) offer a method for high speed full loop characterisation of hard magnetic materials. As there is no dependency on iron to close a circuit, the repeatability of the technique is good. By utilising Peltier effect techniques to control the temperature of the measurement coil systems employed in a Pulsed Field Magnetometer, the level of repeatability of measurements can be significantly improved.     

Structures and electrochromic properties of Ta0.3W0.7Ox thin films deposited by pulsed laser ablation

Electrochromic materials based on mixed metal oxides are of growing importance since improved durability, coloration efficiency and chemical stability, as well as a desirable neutral color could be accomplished in those multicomponent films. In this work, we have used the pulsed laser deposition technique to deposit thin films of Ta_0.3W_0.7O_x on ITO-coated glass substrates in reactive O₂ gas environment at a substrate temperature range of 200 to 700 °C. X-ray diffraction results showed that Ta_0.3W_0.7O_x films begin to crystallize to a cubic phase at substrate temperatures near 700 °C, while films with amorphous structure were obtained at lower substrate temperatures. The lattice constants of the polycrystalline films are similar to those of stoichiometric Ta_0.3W_0.7O_2.85 bulk materials. Optical transmittance of Ta_0.3W_0.7O_x films decreases as the O₂ pressures during deposition decreasing from 5.32 Pa to 0.13 Pa. Electrochromic properties of the Ta_0.3W_0.7O_x films were evaluated in 0.1 M H₃PO₄ electrolyte and the results were compared to those of WO₃ and Ta_0.1W_0.9O_x films deposited also by pulsed laser ablation. The results have demonstrated that the addition of one metal oxide (e.g., Ta₂O₅) into another (e.g., WO₃) is an effective way to alter the electrochromic properties of the individual constituents.     

Steam reforming of gasoline promoted by partial oxidation reaction on novel bimetallic Ni-based catalysts to generate hydrogen for fuel cell-powered automobile applications

Steam reforming of gasoline fuels combined with partial oxidation reaction on ZSM-5-supported Ni-based bimetallic catalysts and Al₂O₃-supported Ni-Re bimetallic catalysts with different Ni/Re ratios for hydrogen generation at a relatively lower reaction temperature was studied. The ZSM-5-supported Ni-Ce and Ni-Mo bimetallic catalysts exhibited a higher activity than the Ni/ZSM-5 catalyst for the oxidative reforming of gasoline. Steam reforming of gasoline to produce hydrogen was remarkably promoted by partial oxidation reaction by addition of molecular oxygen to the reaction system on ZSM-5-supported Ni-Ce catalyst. Al₂O₃-supported Ni-Re catalyst with suitable Ni/Re ratios exhibits unique high activity and sulfur tolerance because of the alloying of Ni with Re to form a new active sites for oxidative steam reforming of gasoline to generate hydrogen. The crystal structure of Al₂O₃-supported bimetallic Ni-Re catalyst and monometallic catalysts of Ni and Re were characterized by XRD method. Structured changes resulting from the alloying of Ni with Re were found.