Enhanced relative permittivity in niobium and europium co-doped TiO2 ceramics

The appearance of colossal permittivity materials broadened the choice of materials for energy-storage applications. In this work, colossal permittivity in ceramics of TiO₂ co-doped with niobium and europium ions ((Eu_0.5Nb_0.5)_xTi_1-xO₂ ceramics) was reported. A large permittivity (ε_r ～ 2.01?×?10⁵) and a low dielectric loss (tanδ ～ 0.095) were observed for (Eu_0.5Nb_0.5)_xTi_1-xO₂ (x?=?1%) ceramics at 1?kHz. Moreover, two significant relaxations were observed in the temperature dependence of dielectric properties for (Eu, Nb) co-doped TiO₂ ceramics, which originated from defect dipoles and electron hopping, respectively. The low dielectric loss and high relative permittivity were ascribed to the electron-pinned defect-dipoles and electrons hopping. The (Eu_0.5Nb_0.5)_xTi_1-xO₂ ceramic with great colossal permittivity is one of the most promising candidates for high-energy density storage applications.     

Synergistic flame retardant effects of activated carbon and molybdenum oxide in poly(vinyl chloride)

The synergistic effects of activated carbon (AC) and molybdenum oxide (MoO₃) in improving the flame retardancy of poly(vinyl chloride) (PVC) were investigated. The effects of AC, MoO₃ and their mixture with a mass ratio of 1:1 on the flame retardancy and smoke suppression properties of PVC were studied using the limiting oxygen index and cone calorimeter tests. It was found that the flame retardancy of the relatively cheaper AC was slightly weaker than that of MoO₃. In addition, the incorporation of AC and MoO₃ greatly reduced the total heat release and improved smoke suppressant property of PVC composites. When the total content of AC and MoO₃ was 10 phr, PVC/AC/MoO₃ had the lowest peak heat release rate and peak smoke production rate values of 173.80 kW m^?2 and 0.1472 m² s^?1, which represented reductions of 47.3 and 59.9%, respectively, compared with those of PVC. Furthermore, thermogravimetric analysis and gel content tests were used to analyze the flame retardant mechanism of AC and MoO₃, with results showing that AC could promote early crosslinking in PVC. Char residue left after heating at 500 °C was analyzed using scanning electron microscopy and Raman spectroscopy, and the results showed that MoO₃ produced the most compact char, with the smallest and most organized carbonaceous microstructures. © 2017 Society of Chemical Industry     

Densification mechanism during reactive hot pressing of B4C-ZrO2 mixtures

The densification behaviors of pure B₄C and B₄C-ZrO₂ mixtures were compared during hot pressing. The results showed that in-situ formed ZrB₂ effectively enhanced the densification process of B₄C-ZrO₂ mixtures, more significantly during the intermediate stage. Within the relative density ranging from 0.75 to 0.90, the B₄C-15?wt%ZrO₂ mixture (B15Z) achieved the maximum densification rate as twice much as that of pure B₄C. The stress exponent n>3 indicated plastic deformation was the dominant densification mechanism of B15Z. The viscosities of plastic flow were evaluated using Murray-Rodger-William equation and the viscosity of B15Z was only a quarter of that in pure B₄C. The sintering activation energy was calculated to be 305.9?kJ/mol for pure B₄C and 197?kJ/mol for B15Z, respectively. It was proposed that the lower viscosity of plastic flow and activation energy accelerated the sliding and propagating motions of plastic flow, by which underlain the enhanced densification behaviors of B₄C-ZrO₂ mixtures.     

Wetting,infiltration and interaction behavior of CMAS towards columnar YSZ coatings deposited by plasma spray physical vapor

Thermal barrier coatings (TBCs) produced by electron beam physical vapor deposition (EB-PVD) or plasma spray (PS) usually suffer from molten calcium-magnesium-alumino-silicate (CMAS) attack. In this study, columnar structured YSZ coatings were fabricated by plasma spray physical vapor deposition (PS-PVD). The coatings were CMAS-infiltrated at 1250?°C for short terms (1, 5, 30?min). The wetting and spreading dynamics of CMAS melt on the coating surface was in-situ investigated using a heating microscope. The results indicate that the spreading evolution of CMAS melt can be described in terms of two stages with varied time intervals and spreading velocities. Besides, the PS-PVD columnar coating (～100?μm thick) was fully penetrated by CMAS melt within 1?min. After the CMAS attack for 30?min, the original feathered-YSZ grains (tetragonal phase) in both PS-PVD and EB-PVD coatings were replaced by globular shaped monoclinic ZrO₂ grains in the interaction regions.     

A novel bio‐based phthalonitrile resin derived from catechin: synthesis and comparison of curing behavior with petroleum‐based counterpart

The development of bio‐based thermosetting resins with good thermal stability can potentially afford sustainable polymers as replacements for petroleum‐based polymers. We report a practical route to a novel catechin‐based phthalonitrile resin precursor (CA‐Ph), which contains free phenolic hydroxyl groups that result in ‘self‐curing’ at elevated temperatures to afford a thermostable polymer. Comparison of the performance of this CA‐Ph resin with that of a conventional petroleum‐based bisphenol A phthalonitrile resin (BPA‐Ph; containing 5 wt% of the curing agent 4,4′‐diaminodiphenylsulfone) revealed that CA‐Ph exhibits a lower melting point and curing temperature. Cured CA‐Ph resin retains 95% of its weight at 520 °C under a nitrogen atmosphere, which compares favorably with results obtained for BPA‐Ph resin that retains 95% of its weight at a lower temperature of 484 °C. Kinetic results indicated that the curing reactions of both CA‐Ph and BPA‐Ph systems follow an autocatalytic mechanism. These results suggest that catechin is a useful bio‐based feedstock for the preparation of self‐curing and thermally stable phthalonitrile resins for advanced technological applications. © 2017 Society of Chemical Industry     

New anti-ablation candidate for carbon/carbon composites: Preparation,composition and ablation behavior of Y2Hf2O7 coating under an oxyacetylene torch

Y₂Hf₂O₇ possesses low thermal conductivity and high melting point, which make it promising for a new anti-ablation material. For evaluating the thermal stability and the potential applications of Y₂Hf₂O₇ on anti-ablation protection of C/C composites, Y₂Hf₂O₇ ceramic powder was synthesized by solution combustion method and Y₂Hf₂O₇ coating was prepared on the surface of SiC coated C/C composites using SAPS. Results shown that the coating exhibits good ablation resistance under the heat flux of 2.4?MW/m² with the linear and mass ablation rates are 0.16?μm?s^?1 and ?0.028?mg?s^?1, respectively, after ablation for 40?s. With the prolonging of the ablation time, the increasing thermal stress causes the increase of cracks. Moreover, the chemical erosion from SiO₂ and the physical volatilization of low temperature molten products aggravate failure of the Y₂Hf₂O₇ coating.     

Fabrication of dense nano-laminated tungsten carbide materials doped with Cr3C2/VC through two-step sintering

This work investigates the critical roles of two-step sintering (TSS) and laminated structure on the sintering behavior and mechanical properties of functionally graded WC-TiC-Al₂O₃ nanostructured composite materials doped with Cr₃C₂/VC. Results show that excellent mechanical properties are achieved for tailored TSS conditions with a hardness of 27.91?±?2.3?GPa and a flexural strength of 1423.3?±?23.5?MPa. The desirable mechanical properties are attributed to the suppressed grain growth without densification deterioration. TSS is more effective in facilitating the favorable dispersion of secondary phase toughening nano-particulates in a WC matrix than conventional sintering (CS). Cr₃C₂/VC dopant plays an important role in maximizing and shifting the temperature range of the kinetic window for WC-Al₂O₃ composites. Al₂O₃ crack deflection, transgranular Al₂O₃, microcracking, WC crack bridging and plate-like WC crack deflection are the major toughening mechanisms. Residual surface compressive stress induced by the graded structure is also an appreciated contribution to the improvement of mechanical properties.     

Ferroelastic domain structure and phase transition in single-crystalline [PbZn1/3Nb2/3O3]1-x[PbTiO3]x observed via in situ x-ray microbeam

(1-x)Pb(Zn_1/3Nb_2/3)O₃-xPbTiO₃ ((1-x)PZN-xPT in short) is one of the most important piezoelectric materials. In this work, we extensively investigated (1-x)PZN-xPT (x = 0.07–0.11) ferroelectric single crystals using in-situ synchrotron μXRD, complemented by TEM and PFM, to correlate microstructures with phase transitions. The results reveal that (i) at 25 °C, the equilibrium state of (1-x)PZN-xPT is a metastable orthorhombic phase for x = 0.07 and 0.08, while it shows coexistence of orthorhombic and tetragonal phases for x = 0.09 and x = 0.11, with all ferroelectric phases accompanied by ferroelastic domains; (ii) upon heating, the phase transformation in x = 0.07 is Orthorhombic → Monoclinic → Tetragonal → Cubic. The coexistence of ferroelectric tetragonal and paraelectric cubic phases was in-situ observed in x = 0.08 above Curie temperature (T_C), and (iii) phase transition can be explained by the evolution of the ferroelectric and ferroelastic domains. These results disclose that (1-x)PZN-xPT are in an unstable regime, which is possible factor for its anomalous dielectric response and high piezoelectric coefficient.     

快速灵敏的LC-MS/MS法测定人血浆中阿莫西林并应用于两种制剂的一致性评价

目的: 建立快速灵敏的LC-MS/MS法测定人血浆中阿莫西林浓度，并用于两种阿莫西林胶囊的一致性评价。方法: 采用岛津公司LCMS-8060型LC-MS/MS仪，以MRM模式测定阿莫西林（m/z 366.00/114.00）的浓度，d4-阿莫西林作内标（m/z 370.10/114.05），离子源为ESI源。色谱柱选用Waters ACQUITY BEH C18（2.1×50 mm，1.7 μm），梯度洗脱。血浆样本加入内标，经甲醇沉淀蛋白后取上清液进样检测。结果: 所建方法经验证，其线性、准确度、精密度、最低定量限、提取回收率、特异性、基质效应、稳定性等各项指标均符合CFDA的指导原则及最新核查标准要求，并较文献报道中的方法有处理简单、灵敏度高、色谱峰形好的优点。结论: 所建方法快速、灵敏，适用于人血浆中阿莫西林浓度的检测。用于一致性评价的样本实测，两种制剂生物等效。     

Using electroencephalogram to continuously discriminate feelings of personal thermal comfort between uncomfortably hot and comfortable environments

Thermal comfort is an important factor for the design of buildings. Although it has been well recognized that many physiological parameters are linked to the state of thermal comfort or discomfort of humans, how to use physiological signal to judge the state of thermal comfort has not been well studied. In this paper, the feasibility of continuously determining feelings of personal thermal comfort was discussed by using electroencephalogram (EEG) signals in private space. In the study, 22 subjects were exposed to thermally comfortable and uncomfortably hot environments, and their EEG signals were recorded. Spectral power features of the EEG signals were extracted, and an ensemble learning method using linear discriminant analysis or support vector machine as a sub-classifier was used to build the discriminant model. The results show that an average discriminate accuracy of 87.9% can be obtained within a detection window of 60 seconds. This study indicates that it is feasible to distinguish whether a person feels comfortable or too hot in their private space by multi-channel EEG signals without interruption and suggests possibility for further applications in neuroergonomics.