基于概率法的电力系统安全分析

为应对电力系统安全分析中的停机问题，基于概率法的方式，将常用的确定停机计算与加入了概率法的概率停机进行比较，研究了二者的区别与其在长期投资方向的不同。在进行电力系统停机分析时，通常会分别从确定停机与概率停机的角度出发，对其应急状态下的潮流进行计算。但前者的方法可能导致极低概率的停机事件被忽略，进而影响长期的资金投资。通过加入概率法的计算，使得对单个停机事件的判定由其具体的频率来确定，增加了系统运行的稳定性。     

Thermo-economic investigation on the hydrogen production through the stored solar energy in a salinity gradient solar pond: A comparative study by employing APC and ORC with zeotropic mixture

In this paper, a salinity gradient solar pond (SGSP) is used to harness the solar energy for hydrogen production through two cycles. The first cycle includes an absorption power cycle (APC), a proton exchange membrane (PEM) electrolyzer, and a thermoelectric generator (TEG) unit; in the second one, an organic Rankine cycle (ORC) with the zeotropic mixture is used instead of APC. The cycles are analyzed through the thermoeconomic vantage point to discover the effect of key decision variables on the cycles’ performance. Finally, NSGA-II is used to optimize both cycles. The results indicate that employing ORC with zeotropic mixture leads to a better performance in comparison to utilizing APC. For the base mode, unit cost product (UCP), exergy, and energy efficiency when APC is employed are 59.9 $/GJ, 23.73%, and 3.84%, respectively. These amounts are 47.27 $/GJ, 29.48%, and 5.86% if ORC with the zeotropic mixture is utilized. The APC and ORC generators have the highest exergy destruction rate which is equal to 6.18 and 10.91 kW. In both cycles, the highest investment cost is related to the turbine and is 0.8275 $/h and 0.976 $/h for the first and second cycles, respectively. In the optimum state the energy efficiency, exergy efficiency, UCP, and H₂ production rate of the system enhances 42.44%, 27.54%,15.95%, and 38.24% when ORC with the zeotropic mixture is used. The maximum H₂ production is 0.47 kg/h, and is obtained when the mass fraction of R142b, LCZ temperature, pumps pressure ratio, generator bubble point temperature are 0.603, 364.35 K, 2.12, 337.67 K, respectively.     

超宽带大功率合成器设计北大核心CSCD

在80 MHz~1 GHz频段,单个功率管输出功率能达到100 W以上,为研制输出功率400 W的功率放大器,文中设计了四路功率合成器。该合成器需要实现功率容量大、工作频带宽、体积小的设计目标。在功率容量方面,文中采用悬置带状线结构,其功率容量远远大于微带线结构;在工作频带方面,采用切比雪夫九节阻抗变换器,将工作带宽拓宽为80 MHz~1 GHz;在体积方面,文中合成器的功率合成部分采用Y型节级联实现四路功率合成,阻抗变换部分采用切比雪夫阻抗变换器进行阻抗变换,该结构相较于磁环巴伦功率合成器,不但具有损耗小、平坦度高的优点,而且通过将阻抗变换器设计成曲折的形状,进一步缩小了合成器体积。仿真与实测结果显示该合成器在80 MHz~1 GHz范围内还具有较高的平坦度,合成效率可达90%以上。     

关于新疆热电厂职业危害分析与讨论

对比不同热电厂企业工人接触职业危害因素情况,分析原因,为在建或已建热电厂提供职业危害因素预防措施,降低企业由于设计、施工或管理方面原因造成后期运行过程中职业危害接触超标情况的发生。根据我室历年对新疆地区热电厂职业危害因素检测结果与评价报告的比较,找出不同热电厂职业病危害因素的共性及异性,分析不同设备、工艺及管理方式不同所造成职业危害因素检测结果的差异及原因。建议优化厂区工艺及土建设计;优化设备选型及原料选择运用现代化的管理手段,加强职业卫生管理体系宣贯的有效运作。     

High-resolution FIB-TEM-STEM structural characterization of grain boundaries in the high dielectric constant perovskite CaCu3Ti4O12

In this work, the grain boundaries composition of the polycrystalline CaCu₃Ti₄O₁₂ (CCTO) was investigated. A Focused Ion Beam (FIB)/lift-out technique was used to prepare site-specific thin samples of the grain boundaries interface of CCTO ceramics. Scanning transmission electron microscopy (STEM) coupled with energy dispersive X-ray spectrometry (EDXS) and Electron Energy Loss Spectroscopy (EELS) systems were used to characterize the composition and nanostructure of the grain and grain boundaries region. It is known that during conventional sintering, discontinuous grain growth occurs and a Cu-rich phase appears at grain boundaries. This Cu-rich phase may affect the final dielectric properties of CCTO but its structure and chemical composition remained unknown. For the first time, this high-resolution FIB-TEM-STEM study of CCTO interfacial region highlights the composition of the phases segregated at grain boundaries namely CuO, Cu₂O and the metastable phase Cu₃TiO_4.     

水泥窑余热发电系统用耐磨材料的研制与应用

本研究针对水泥窑余热发电系统的工作条件,根据耐磨材料的损毁机理,采用高铝矾土、煅烧氧化铝粉、黏土、硅微粉等为原料,以磷酸二氢铝为结合剂,以铝酸钙水泥为促硬剂,通过添加掩蔽剂和优化配料工艺,制备了水泥窑余热发电系统用耐磨材料,并对不同处理温度对耐磨材料的性能影响进行了分析。结果表明增强骨料与基质的结合能力有利于耐磨性的提高,磷酸及磷酸盐与氧化铝之间会随着温度的升高生成不同的磷酸铝相,都能够起到结合作用,比采用水泥结合更有利于提高材料在不同温度下的强度和耐磨性。使用结果表明,制备的耐磨材料施工性能优良,凝结硬化时间适当,强度高,抗冲刷性能好,在水泥窑余热发电系统中取得了良好的使用效果。     

Elitist clonal selection algorithm for optimal choice of free knots in B-spline data fitting

Data fitting with B-splines is a challenging problem in reverse engineering for CAD/CAM, virtual reality, data visualization, and many other fields. It is well-known that the fitting improves greatly if knots are considered as free variables. This leads, however, to a very difficult multimodal and multivariate continuous nonlinear optimization problem, the so-called knot adjustment problem. In this context, the present paper introduces an adapted elitist clonal selection algorithm for automatic knot adjustment of B-spline curves. Given a set of noisy data points, our method determines the number and location of knots automatically in order to obtain an extremely accurate fitting of data. In addition, our method minimizes the number of parameters required for this task. Our approach performs very well and in a fully automatic way even for the cases of underlying functions requiring identical multiple knots, such as functions with discontinuities and cusps. To evaluate its performance, it has been applied to three challenging test functions, and results have been compared with those from other alternative methods based on AIS and genetic algorithms. Our experimental results show that our proposal outperforms previous approaches in terms of accuracy and flexibility. Some other issues such as the parameter tuning, the complexity of the algorithm, and the CPU runtime are also discussed.     

Distributed wireless power transfer in sensor networks with multiple Mobile Chargers

We investigate the problem of efficient wireless power transfer in wireless sensor networks. In our approach, special mobile entities (called the Mobile Chargers) traverse the network and wirelessly replenish the energy of sensor nodes. In contrast to most current approaches, we envision methods that are distributed and use limited network information. We propose four new protocols for efficient charging, addressing key issues which we identify, most notably (i) what are good coordination procedures for the Mobile Chargers and (ii) what are good trajectories for the Mobile Chargers. Two of our protocols (DC, DCLK) perform distributed, limited network knowledge coordination and charging, while two others (CC, CCGK) perform centralized, global network knowledge coordination and charging. As detailed simulations demonstrate, one of our distributed protocols outperforms a known state of the art method, while its performance gets quite close to the performance of the powerful centralized global knowledge method.     

泛在电力物联网在北京经济技术开发区的应用探索

泛在电力物联网是物联网在电力领域的具体体现，建设泛在电力物联网是推进"三型两网"建设的关键环节，也是实现能源转型的必要手段。阐述了泛在电力物联网的定义，从供电公司角度出发，根据北京经济技术开发区实际情况，讨论了依托地区特点的泛在电力物联网实施策略和实际应用场景，分析了可能遇到的问题。得出结论：随着泛在电力物联网的深入建设，供电公司能够为电力客户提供多元化服务，提高客户满意度；地市供电公司能够依托泛在电力物联网开展更多电力相关业务；泛在电力物联网的安全性、实用性、有效性是发展面临的首要问题。     

Surface modification of poly(tetrafluoroethylene) and poly(ethylene terephthalate) films via environmental crazing

This work addresses the phenomenon of the development of a patterned surface relief on polymer films via different modes of environmental crazing. Commercial films of semicrystalline poly(tetrafluoroethylene) (PTFE) and amorphous glassy poly(ethylene terephthalate) (PET) were subjected to tensile drawing in the presence of physically active liquid environments (carbon tetrachloride or aliphatic alcohols). The structure parameters and wettability of the modified films were studied by AFM, SEM, profilometer measurements and contact angle measurements. Environmental intercrystallite crazing of PTFE is accompanied by the development of an unstable structure with a high free surface, which experiences marked strain recovery upon unloading. As a result of the relief formation, PTFE hydrophobicity is enhanced (the water contact angle increases by 25°). Classical environmental crazing of PET films is accompanied by the formation of an anisotropic surface relief which is an assembly of crazes oriented perpendicular to the direction of tensile drawing, thus leading to the phenomenon of anisotropic wetting. The proposed approach for structural surface modification makes it possible to use the advantages of surface instability and spontaneous self‐organization of the polymer towards the development of a unique surface microrelief. © 2020 Society of Chemical Industry