平均声压级近似计算误差分析

本文用凸集理论分析了平均声压级近似计算的误差,导出了最大误差计算公式,指出了测量数据在何种状态下误差达到最大值。     

压力传感器的应力计算

从弹性力学的板壳理论出发,对不同参数的凸型板结构形变膜受压后的应力分布作了近似计算,为高线性度SOI压力传感器的芯片设计提供了理论指导。用BESOI技术研制的凸型板结构集成压力传感器的非线性度达0 09%,样品灵敏度的实测值与应力计算理论值的差别约17%。     

氢对2.25Cr-1Mo压力容器用钢力学性能影响

基于试样高温高压釜充氢方法 ,研究了氢对 2 2 5Cr 1Mo压力容器用钢力学性能的影响。对充氢前后的试样进行了拉伸和CVN冲击试验 ,结果表明 ,氢对 2 2 5Cr 1Mo钢的拉伸力学性能和冲击韧性影响不显著。     

多孔材料气体流量的简便计算

采用简便方法计算气体通过多孔材料的流量。当层流时，流量与压差按线性关系计算；紊流时，应按幂函数关系计算。本文提出了计算公式。     

水头差压力转换提水技术研究

本文阐述了一项水能利用的新技术：通过密闭容器将水的落差转换成压力气体，再通过压力气体去压缩另一密闭容器内的水。进而实现提水的目的。实验、计算和分析显示，这是一种切实可行的提水新技术。     

GEOLOGICAL MODEL EVALUATION THROUGH WELL TEST SIMULATION: A CASE STUDY FROM THE WYTCH FARM OILFIELD, SOUTHERN ENGLAND

This paper presents an approach to the evaluation of reservoir models using transient pressure data. Braided fluvial sandstones exposed in cliffs in SW England were studied as the surface equivalent of the Triassic Sherwood Sandstone, a reservoir unit at the nearby Wytch Farm oilfield. Three reservoir models were built; each used a different modelling approach ranging in complexity from stochastic pixel‐based modelling using commercially available software, to a spreadsheet random number generator. In order to test these models, numerical well test simulations were conducted using sector models extracted from the geological models constructed. The simulation results were then evaluated against the actual well test data in order to find the model which best represented the field geology. Two wells at Wytch Farm field were studied. The results suggested that for one of the sampled wells, the model built using the spreadsheet random number generator gave the best match to the well test data. In the well, the permeability from the test interpretation matched the geometric average permeability. This average is the “correct” upscaled permeability for a random system, and this was consistent with the random nature of the geological model. For the second well investigated, a more complex “channel object” model appeared to fit the dynamic data better. All the models were built with stationary properties. However, the well test data suggested that some parts of the field have different statistical properties and hence show non‐stationarity. These differences would have to be built into the model representing the local geology. This study presents a workflow that is not yet considered standard in the oil industry, and the use of dynamic data to evaluate geological models requires further development. The study highlights the fact that the comparison or matching of results from reservoir models and well‐test analyses is not always straightforward in that different models may match different wells. The study emphasises the need for integrated analyses of geological and engineering data. The methods and procedures presented are intended to form a feedback loop which can be used to evaluate the representivity of a geological model.     

江苏沙河抽水蓄能电站工程上进出水口设计

介绍了江苏沙河抽水蓄能电站上进出水口设计特点,上进水口体型参数的确定,工程处理措施,结构稳定分析和结构计算。     

注气井中油管轴向位移计算比较分析

为了确定油管在正常作业、注入措施作业中封隔器的坐封位置、轴向位移补偿量以及判断封隔器是否解封,根据弹性力学理论得出了不同条件下油管柱的轴向位移量,综合考虑了在不同工况下由活塞效应、螺旋弯曲、径向压力、温度变化、松弛力以及摩阻等因素引起的油管轴向位移;同时考虑了在注气油管内气体的横向压力效应,运用VB语言编制程序,将各自计算结果进行了比较分析。结果表明,在注气油管内考虑横向压力效应时与常规油管长度计算油管轴向位移有明显差异;油管内液体流动引起的油管轴向伸长与注入速度的平方成正比,在注入速度过大时对轴向位移有明显影响。     

应用ATV71变频器有效解决给粉机变频器低电压跳闸问题

本文分析了给粉机变频器低电压跳闸的原因和解决办法，为解决给粉机变频器低电压跳闸，消除设备隐患提供了经验。     

极压,油性添加剂在磨削过程中的作用

油性及极压添加剂为磨削液中主要减摩添加剂，本文从物理及化学两个方面分析了两种添加剂在磨削过程中的作用机理，说明了两种添加剂的相辅作用，并采用不同的磨削液进行了实验验证．