油煤浆的管道输送特性与管路设计原则

通过理论分析和管道实验，探讨了油煤浆在工业管道输送中的流变特性、流动状态和阻力特性，得出了油煤浆的物性参数、表观参数、管道阻力参数的测定值和计算公式，并在此基础上探讨了油煤浆管道输送的设计原则，为油煤浆管路的设计提供基础数据、计算方法和一般原则。     

饮用水中挥发性三卤甲烷(THM)_s测定方法的改进

本文使用吹扫捕集法来前处理水样,用带有电子捕获检测(ECD)的气相色谱仪来测定水中三卤甲烷(THM)_s。水样加标回收率在85%～115%之间,相对标准偏差在5%左右。实验结果表明,该法具有简单、快速、灵敏的特点。     

A localized surface plasmon resonance based immunosensor for the detection of casein in milk

In this research, a localized surface plasmon resonance (LSPR) immunosensor based on gold-capped nanoparticle substrate for detecting casein, one of the most potent allergens in milk, was developed. The fabrication of the gold-capped nanoparticle substrate involved a surface-modified silica nanoparticle layer (core) on the slide glass substrate between bottom and top gold layers (shell). The absorbance peak of the gold-capped nanoparticle substrate was observed at ∼520 nm. In addition, the atomic force microscopy (AFM) images demonstrated that the nanoparticles formed a monolayer on the slide glass. After immobilizing anti-casein antibody on the surface, our device, casein immunosensor, could be applied easily for the detection of casein in the raw milk sample without a difficult pretreatment. Under the optimum conditions, the detection limit of the casein immunosensor was determined as 10 ng/mL. Our device brings several advantages to the existing LSPR-based biosensors with its easy fabrication, simple handling, low-cost, and high sensitivity.     

AgWC12C3的粉末粒度对产品密度的影响

粉末粒度对粉末制品的性能具有重要的影响,而这些影响主要通过改善材料的密度来达到。该文根据模拟粉末堆积模型,确定相对合理的粒度组成,并通过试验予以验证。     

Modelling velocity saturation and kink effects in p-channel polysilicon thin-film transistors

Experimental measurements and full-2D numerical simulations show that velocity saturation effects in polysilicon thin-film transistor (TFTs) cannot be neglected in order to obtain a precise modelling of output characteristics. Since full-2D numerical simulations are time consuming and unpractical for circuit simulations, we have developed a new quasi-2D model, that takes into account both velocity saturation effects and the presence of a longitudinal electric field in the Poisson's equation, and includes the effect of parasitic bipolar transistor (PBT) action to reproduce kink effect. The agreement of the quasi-2D model with experimental data from p-channel polysilicon TFTs is very satisfactory even for short channel device, and the presence of a velocity-saturated region with a nearly constant free carrier concentration is reproduced without introducing further assumptions.     

Polyamide-6/vegetal fiber composite prepared by extrusion and injection molding

The interest for the use of vegetal fibers as polymers reinforcement has recently increased because of their unique environmental and technological advantages. This work evaluated the use of Curauá fibers in polyamide-6 composites aiming at glass fiber replacement. Fiber content of 20, 30 or 40 wt% and fiber lengths of 0.1 or 10 mm were studied. Fibers were treated with N₂ plasma or washed with NaOH solution, to improve their adhesion to PA-6. Samples with 20 wt% of short or long fibers, with or without pre-treatment, were compounded in two different co-rotating intermeshing twin-screw extruders. These samples were submitted to mechanical and thermal tests. In conclusion, non-dried raw materials improved fiber/matrix interfacial adhesion. Tensile and flexural properties of this composite are better than unfilled, but lower than glass fiber reinforced polyamide-6. However, its impact resistance and heat deflection temperature are similar to the glass fiber reinforced polyamide-6 and its lower density, enable it to replace this latter in specific non-critical applications.     

Investigation of the Correlation between Texture and Microstructure on a Submicrometer Scale in the TEM

In recent years the investigation of local texture and microstructure by analysis of electron backscatter diffraction patterns (EBSP) in the SEM has become a very powerful and popular method. With the introduction of SEM with field emission guns (FEG) the spatial resolution of EBSP measurements could be enhanced from 500 nm with a tungsten emitter to better than 50 nm. This evolution of SEM techniques raises the question whether transmission electron microscopy (TEM) still has fields of application in texture research. The present article answers this question with a clear “yes” and presents three examples of investigations where TEM is indispensable. The three examples comprise the investigation of the correlation between dislocation structure and deformation texture, a study on nucleation mechanisms of recrystallization in highly deformed metals and the investigation of microtexture and microstructure in nanocrystalline materials. Together with the presentation of these cases some of the necessary measurement techniques are described briefly. It is shown that TEM has to be applied when highest spatial resolution of orientation determination and imaging and high accuracy of orientation determination are to be reached, when the three‐dimensional and quantitative characterization of lattice defects is required or when materials with a high density of lattice defects are to be investigated.     

Improvement of photon collection in Cu(In,Ga)Se2 solar cells and modules by fluorescent frequency conversion

Fluorescent photon down conversion for the improvement of the blue response of ZnO/CdS/Cu(In,Ga)Se₂ heterojunction solar cells and modules is investigated. Fluorescent dyes of the series Lumogen® F are analyzed by optical transmission and reflection as well as by photoluminescence measurements. A spectral transfer matrix formalism is introduced that allows to predict the suitability of a luminescent dye as a down-converter for a given solar cell from its absorption/emission properties. We find that Lumogen® F Violet 570 and Lumogen® F Yellow 083 as well as a combination of both yields improvements for Cu(In,Ga)Se₂ solar modules. Particularly, we find that the short circuit current density of a Cu(In,Ga)Se₂ mini-module is improved by 1.5 mA cm^− 2 when applying a varnish with a combination of Lumogen® F Violet and Yellow. About 0.5 mA cm^− 2 of this improvement is due to a reduced overall reflectance and an improvement of 1 mA cm^− 2 results from the frequency conversion by the dyes.