环缝错边容器的有限元分析与容限探讨

采用有限元方法对 1台封头与筒体具有较大错边量的容器进行了应力分析 ,得到了错边区域的应力分布状况 ,并对其进行应力强度评定。结果表明 ,该容器错边部位的应力是满足应力分析准则的。通过对存在不同错边量的容器进行应力分析 ,探讨了容器的错边容限 ,对含有错边缺陷在役容器是否合乎使用的判断具有一定指导意义     

中原高温高盐油藏疏水缔合聚合物凝胶调剖剂研究

针对中原油田高温(>80℃)、高盐度(>50 g/L)、高硬度(>1 g/L)砂岩油藏,研制了地下成胶的高热稳定性聚合物凝胶调剖剂。所用聚合物为疏水缔合聚合物AP-P4,M=9.0×106,HD=27%,疏水基摩尔分数0.2%;交联剂为可生成酚醛树脂的3种化合物;调剖剂胶液用矿化度160 g/L的马寨油田污水配制;实验温度95℃。根据形成的凝胶黏度(95℃,1.1 s-1)确定交联剂各组分用量为:MZ-YL 0.429%,MZ-BE 0.060%,MZ-XS 0.012%;酸度调整剂用量0.12%;成胶时间10~15小时。2.5、3.0、3.5 g/L AP-P4的凝胶在95℃老化100天后黏度保持在~40 Pa.s及以上。初配制胶液在3000 r/min下剪切15分钟后黏度降低87.5%~89.0%,但成胶后和老化过程中凝胶黏度只比未剪切样降低17.1%~6.6%。3.5 g/L AP-P4的调剖剂对~1μm2的6支储层岩心的堵塞率在88.1%~95.8%范围,平均93.3%,造成的残余阻力系数在15.2~28.6范围,平均19.8,使渗透率级差2.3~8.0的4组双人造岩心的注水流量比发生不同程度的反转。认为该凝胶调剖剂高温下稳定性好的原因,是强化学交联密度低,因而凝胶脱水收缩作用弱。图2表5参5。     

Insulating safety analysis of the hot-line sweeping robot

This paper presents a method of calculating the insulating safety distances for hot-line working robots at high voltage when dielectric is adulterated with conducts. Also, finite element method is adopted to calculate the electric field strength to find whether it is beyond the critical. The above methods have been applied to analyze the insulating safety of the robot for hot-line sweeping post insulators in a 220 KV substation. They have also been testified by experimentations.     

First-principle study of ferroelectricity in PbTiO3/SrTiO3 superlattices

We performed the first-principles calculation to investigate the electronic structure and polarization behaviors in PbTiO₃/SrTiO₃ (PST) superlattices. The DOS (density of state) profiles show that there are strong hybridizations of atom Ti–O and Pb–O which play very important roles on ferroelectricity of the PbTiO₃/SrTiO₃ superlattices. Comparing to the corresponding paraelectric phase, we find the electrons of the PT (PbTiO₃) layers occupy lower energy states and electrons of the ST (SrTiO₃) layer occupy higher energy states. It is shown that the polarizations of the superlattices decrease with proportion of SrTiO₃ increasing. The constant polarization of local layer indicates that PST superlattices with small modulation lengthen can be approximately considered as a single ferroelectric material. Furthermore, according to electrostatic model, we find that directions of internal electric fields in PT and ST layers are opposite. In PST superlattices, internal electric field in PT layer leads to the loss of polarization of this layer, but the polarization of ST layer is induced by internal electric field of this layer. Compared to the value of the polarization in bulk PbTiO₃, polarization of PST is smaller.     

A New Method for Comparing Orthonasal and Retronasal Olfaction.

Odors seem to be perceived differently when presented ortho- or retronasally. In this study, stimuli of controlled concentration and duration were applied in either the anterior nasal cavity or epipharynx by means of air-dilution olfactometry. Stimulus concentration was monitored in the olfactory cleft. In Experiment 1, odor thresholds to a food (chocolate) and a nonfood (lavender) odor were lower for orthonasal, compared with retronasal, stimulation. In Experiment 2, intensity ratings to suprathreshold odor concentrations were significantly higher for orthonasal than for retronasal stimulation with hydro- hydrogen sulfide, but not phenyl ethyl alcohol. Accordingly, amplitudes and latencies of olfactory event-related gen potentials to retronasal stimuli were found to be smaller and prolonged, respectively. This indicates differential processing of olfactory stimuli presented through the retronasal or orthonasal routes. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

A new numerical analysis for a semi-circular surface crack

This note is concerned with a surface semi-circular crack by using the fracture analysis software FRANC3D developed by a fracture mechanics investigation group of Cornell University. Attention is specifically paid to the effect of the boundaries parallel to the crack on the stress intensity factors (SIFs).     

Approximating the problem, not the solution: An alternative view of point set matching

This work discusses the issue of approximation in point set matching. In general, one may have two classes of approximations when tackling a matching problem: (1) an algorithmic approximation which consists in using suboptimal procedures to infer the assignment, and (2), a representational approximation which involves a simplified and suboptimal model for the original data. Matching techniques have typically relied on the first approach by retaining the complete model and using suboptimal techniques to solve it. In this paper, we show how a technique based on using exact inference in simple Graphical Models, an instance of the second class, can significantly outperform instances of techniques from the first class. We experimentally compare this method with well-known Spectral and Relaxation methods, which are exemplars of the first class. We have performed experiments with synthetic and real-world data sets which reveal significant performance improvement in a wide operating range.     

Design and evaluation of an active electromechanical wheel suspension system

This paper presents an electromechanical wheel suspension, where the upper arm of the suspension has been provided with an electric levelling and a damper actuator, both are allowed to work in a fully active mode. A control structure for the proposed suspension is described. The complex design task involving the control of the electric damper and its machine parameters is tackled by genetic optimisation. During this process, these parameters are optimised to keep the power dissipation of the electric damper as low as possible, while maintaining acceptable comfort and road-holding capabilities. The results of the evaluations carried out demonstrate that the proposed suspension can easily adopt its control parameters to obtain a better compromise of performance than that offered by passive suspensions. If the vehicle is to maintain acceptable performance during severe driving conditions, the damper has to be unrealistically large. However, if the electric damper is combined with a hydraulic damper, the size of the electric damper is significantly reduced. In addition, the design of the electric damper with the suggested control structure, including how it regenerates energy, is discussed.     

伴随内转换电子发射的俄歇电子能量及强度计算

简要介绍了伴随内转换电子发射产生的俄歇电子能量与强度的计算方法、计算程序及工作流程，并以^129Iβ^-衰变为例说明其具体应用。     

Motion compensated film restoration

Motion picture films are susceptible to local degradations such as dust spots. Other deteriorations are global such as intensity and spatial jitter. It is obvious that motion needs to be compensated for before the detection/correction of such local and dynamic defects. Therefore, we propose a hierarchical motion estimation method ideally suited for high resolution film sequences. This recursive block-based motion estimator relies on an adaptive search strategy and Radon projections to improve processing speed. The localization of dust particles then becomes straightforward. Thus, it is achieved by simple inter-frame differences between the current image and motion compensated successive and preceding frames. However, the detection of spatial and intensity jitter requires a specific process taking advantage of the high temporal correlation in the image sequence. In this paper, we present our motion compensation-based algorithms for removing dust spots, spatial and intensity jitter in degraded motion pictures. Experimental results are presented showing the usefulness of our motion estimator for film restoration at reasonable computational costs. Received: 9 July 2000 / Accepted: 13 January 2002 Correspondence to:S. Boukir