Ion beam induced evolution of surface morphology and optical properties of SnO2–ZnO nanocomposite thin films

SnO₂–ZnO nanocomposite thin films, prepared by a simple carbothermal reduction based vapor deposition method, were irradiated with 8 MeV Si³⁺ ions for engineering the morphological and optical properties. The surface morphology of the nanocomposites was studied by atomic force microscopy (AFM), while the optical properties were investigated by photoluminescence spectroscopy (PL) and Raman spectroscopy. AFM studies on the irradiated samples revealed growth of nanoparticles at lower fluence and a significant change in surface morphology leading to the formation of nanosheets and their aggregates at higher fluences. A tentative mechanism underlying the observed ion induced evolution of surface morphology of SnO₂–ZnO nanocomposite is proposed. PL studies revealed strong enhancement in the UV emissions from the nanocomposite thin film at lower fluence, while a drastic decrease in the UV emissions along with a significant enhancement in the defect emissions has been observed at higher fluences.     

Improvement of adhesion and paint ability of EVA copolymers with different vinyl acetate contents by treatment with UV-ozone

The surface modifications produced by UV-ozone treatment of two ethylene-vinyl acetate (EVA) copolymers containing 12 and 20 wt% vinyl acetate (EVA12 and EVA20 respectively) were studied. The treatment with UV-ozone improved the wettability of both EVAs due to the creation of new carbon–oxygen moieties. The extent of these modifications increased with increasing length of the treatment and the modifications produced in EVA20 were produced for shorter lengths of treatment. The UV-ozone treatment also created roughness and heterogeneities on the EVA surfaces. Whereas roughness formation prevailed on the UV-ozone treated EVA12, important ablation was dominant on the treated EVA20. T-peel strength values in joints made with polychloroprene adhesive increased when the EVAs were treated with UV-ozone. Short length of UV-ozone treatment (1 min) produced higher T-peel strength in joints made with EVA20 whereas higher T-peel strength values in joints made with EVA12 were obtained after treatment for 5–7.5 min in which a cohesive failure into a weak boundary layer on the treated EVA surface was found. Furthermore, the adhesion of UV-ozone treated EVA20 to acrylic paint increased. Finally, the ageing resistance of the treated EVA/polychloroprene adhesive joints was good and the surface modifications on the UV-ozone treated EVAs lasted for 24 h after treatment at least.     

Nonlinear response in glass fibre non-crimp fabric reinforced vinylester composites

This paper addresses the nonlinear stress-strain response in glass fibre non-crimp fabric reinforced vinylester composite laminates subjected to in-plane tensile loading. The nonlinearity is shown to be a combination of brittle and plastic failure. It is argued that the shift from plastic to brittle behaviour in the vinylester is caused by the state of stress triaxiality caused by the interaction between fibre and vinylester. A model combining damage and plasticity is calibrated and evaluated using data from extensive experimental testing. The onset of damage is predicted using the Puck failure criterion, and the evolution of damage is calibrated from the observed softening in plies loaded in transverse tension. Shear loading beyond linear elastic response is observed to result in irreversible strains. A yield criterion is implemented for shear deformation. A strain hardening law is fitted to the stress-strain response observed in shear loaded plies. Experimental results from a selection of laminates with different layups are used to verify the numerical models. A complete set of model parameters for predicting elastic behaviour, strength and post failure softening is presented for glass fibre non-crimped fabric reinforced vinylester. The predicted behaviour from using these model parameters are shown to be in good agreement with experimental results.     

Alloying behavior and novel properties of CoCrFeNiMn high-entropy alloy fabricated by mechanical alloying and spark plasma sintering

An equiatomic CoCrFeNiMn high-entropy alloy was synthesized by mechanical alloying (MA) and spark plasma sintering (SPS). During MA, a solid solution with refined microstructure of 10 nm which consists of a FCC phase and a BCC phase was formed. After SPS consolidation, only one FCC phase can be detected in the HEA bulks. The as-sintered bulks exhibit high compressive strength of 1987 MPa. An interesting magnetic transition associated with the structure coarsening and phase transformation was observed during SPS process.     

Electromagnetic shielding properties of iron oxide impregnated kenaf bast fiberboard

The electromagnetic shielding effectiveness of kenaf fiber based composites with different iron oxide impregnation levels was investigated. The kenaf fibers were retted for removing the lignin and extractives from the fibers and magnetized. Using the unsaturated polyester and the magnetized fibers, kenaf fiber based composites were manufactured by the compression molding process. The transmission energies of the composites were characterized when the composite samples were exposed under the irradiation of electromagnetic (EM) wave with a variable frequency from 9 GHz to 11 GHz. Using the Scanning Electron Microscope (SEM), the iron oxide nanoparticles were observed on the surfaces and inside the micropore structures of single fibers. As the Fe content increased from 0% to 6.8%, 15.9% and 18.0%, the total surface free energy of kenaf fibers with the magnetizing treatments increased from 44.8 mJ/m² to 46.1 mJ/m², 48.8 mJ/m² and 53.0 mJ/m², respectively, while the modulus of elasticity reduced from 2875 MPa to 2729 MPa, 2487 MPa and 2007 MPa, respectively. Meanwhile, the shielding effectiveness was increased from 30–50% to 60–70%, 65–75% and 70–80%, respectively.     

Burkholderia thailandensis E264/pBMTL3-tdpR发酵生产抗癌药物ThailandepsinA的研究

在伯克氏菌Bth264野生株产新型抗癌药物Thailandepsin A以及调节基因tdp R正向调控Thailandepsin A生物合成的基础上,利用基因工程菌Bth264/p BMTL3-tdp R发酵生产Thailandepsin A,以提高产量。以0.5%乳糖为诱导剂,确定最佳诱导条件:发酵15 h添加乳糖,诱导时间6 h;通过单因素实验,确定葡萄糖和胰蛋白胨作为碳氮源、装液量65/250 m L以及接种量1%;同时结合优化发酵培养基进行发酵,Thailandepsin A产量达到252.14 mg·L-1,比优化前的产量提高56%;另外在发酵过程中,添加大孔树脂HP-20原位吸附产物,Thailandepsin A产量可达283.75 mg·L-1,比不加树脂提高13.8%;最后,基于RT-PCR和比较Ct值法,基因工程菌和野生菌相比,Thailandepsin A生物合成基因tdp B、tdp C1的转录水平分别提高11.4倍和6.0倍,对应的产量增加4.6倍,从而在很大程度上说明调节基因tdp R的过表达促进生物合成基因转录水平的提高以及产量的增加。     

Quality and Emulsion Stability of Milk from Ettawah Crossed Bred Goat During Frozen Storage

Goat milk has specific chemical composition and physical properties. The purpose of this study was to investigate the change of milk quality and emulsion stability during 60 d frozen storage. Milk sample was taken from three Ettawah Crossedbred goats that were divided into three groups. Samples were frozen and stored for 0, 30 and 60 days. At the end of each storage periode, milk sample was thawed in the refrigerator and analyzed for total number of bacteria, chemical (acidity, pH, free fatty acids), physical (alcohol test, clot on boiling test) quality, and emulsion stability. The microbiological and chemical data were analyzed statistically using one way ANOVA, whereas physical quality and emulsion stabilty were expressed qualitatively. There were no change in the total bacteria, acidity, pH and free fatty acid (FFA) of milk during storage, whereas the assessment by 70% alcohol showed positive since 0 d. Emulsions stability changed after 30 d of storage. While, the clot on boiling (COB) test of milk was positive at 60 d of storage. Recommendation is frozen storage of goat milk should not longer than 30 d.     

Stream-Based Data Sampling Mechanism for Process Object

Process object is the instance of process. Vertexes and edges are in the graph of process object. There are different types of the object itself and the associations between object. For the large-scale data, there are many changes reflected. Recently, how to find appropriate real-time data for process object becomes a hot research topic. Data sampling is a kind of finding c hanges o f p rocess o bjects. There i s r equirements f or s ampling to be adaptive to underlying distribution of data stream. In this paper, we have proposed a adaptive data sampling mechanism to find a ppropriate d ata t o m odeling. F irst o f all, we use concept drift to make the partition of the life cycle of process object. Then, entity community detection is proposed to find changes. Finally, we propose stream-based real-time optimization of data sampling. Contributions of this paper are concept drift, community detection, and stream-based real-time computing. Experiments show the effectiveness and feasibility of our proposed adaptive data sampling mechanism for process object.     

A New NTRU-Type Public-Key Cryptosystem over the Binary Field

As the development of cloud computing and the convenience of wireless sensor netowrks, smart devices are widely used in daily life, but the security issues of the smart devices have not been well resolved. In this paper, we present a new NTRU-type public-key cryptosystem over the binary field. Specifically, the security of our scheme relies on the computational intractability of an unbalanced sparse polynomial ratio problem (DUSPR). Through theoretical analysis, we prove the correctness of our proposed cryptosystem. Furthermore, we implement our scheme using the NTL library, and conduct a group of experiments to evaluate the capabilities and consuming time of encryption and decryption. Our experiments result demonstrates that the NTRU-type public-key cryptosystem over the binary field is relatively practical and effective.     

Super-Resolution Reconstruction of Images Based on Microarray Camera

In the field of images and imaging, super-resolution (SR) reconstruction of images is a technique that converts one or more low-resolution (LR) images into a highresolution (HR) image. The classical two types of SR methods are mainly based on applying a single image or multiple images captured by a single camera. Microarray camera has the characteristics of small size, multi views, and the possibility of applying to portable devices. It has become a research hotspot in image processing. In this paper, we propose a SR reconstruction of images based on a microarray camera for sharpening and registration processing of array images. The array images are interpolated to obtain a HR image initially followed by a convolution neural network (CNN) procedure for enhancement. The convolution layers of our convolution neural network are 3×3 or 1×1 layers, of which the 1×1 layers are used to improve the network performance particularly. A bottleneck structure is applied to reduce the parameter numbers of the nonlinear mapping and to improve the nonlinear capability of the whole network. Finally, we use a 3×3 deconvolution layer to significantly reduce the number of parameters compared to the deconvolution layer of FSRCNN-s. The experiments show that the proposed method can not only ameliorate effectively the texture quality of the target image based on the array images information, but also further enhance the quality of the initial high resolution image by the improved CNN.