Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Thermal expansion characteristics of a titanium modified austenitic stainless steel: measurement by high-temperature X-ray diffraction and modelling using Grüneisen formalism

The thermal expansion of a titanium modified, swelling resistant austenitic stainless steel designated as D9 is studied by measuring the lattice parameter as a function of temperature in the range 300-1300 K by high-temperature X-ray diffraction technique. The thermal expansion data thus obtained is in reasonable agreement with the typical thermal expansion values reported for similar nuclear grade austenitic stainless steels. However, at temperatures exceeding 900 K, the measured thermal expansivity exhibits a pronounced non-linear increase due partly to the precipitation of complex carbide and intermetallic phases. The high-temperature thermal expansion data obtained in the present study are augmented by modelling the low-temperature thermal expansion behaviour by Grüneisen formalism.     

西气东输工程用X70热轧板卷屈服强度检测值波动大的探讨

对西气东输工程用X70热轧板卷检验过程中出的屈服强度σ0.5波动大的情况进行了分析，认为拉伸试样弯曲是主要原因。这一问题可通过反复压平试样，确保试样的平直度以及适当提高钢的强度的方法加以解决。     

Influence of the surface conditions on permeation in the deuterium–MANET system

The condition of the surfaces is of crucial importance for the deuterium permeation through materials. In this work a study of the surface constants for the adsorption (σk₁) and release (σk₂) of deuterium under different surface conditions on the martensitic steel DIN 1.4914 (MANET) has been carried out. The growth of an oxide surface layer (Cr₂O₃) of about 25–30 nm in a MANET sample, heat treated in an oxidizing environment, compared to the bare MANET that have a ‘natural' oxide of about 5 nm has provoked a reduction of both the permeation rate and the recombination coefficient (about 3 orders of magnitude). In addition, the permeation governing process has changed from diffusion-limited to surface-limited. The measurements of the permeation rate of deuterium were performed by a gas-phase permeation technique over the temperature range 574–746 K and for deuterium driving pressures in the range from 3 to 10⁵ Pa.     

SW233 PIN驱动器自动测试系统的研制

介绍了一种集成电路自动测试系统，该系统采用计算机并口作通信接口，用VB6编程，实现了对外围测试电路的控制，用IEEE-488接口卡控制测试仪器，可对SW233电路的36个参数进行自动测试，并将测试结果自动保存在数据库中。该测试系统具有自动化程度高、操作方便、测试结果精确等特点。     

金刚石光电导探测器研制及在软X光测量中的初步应用

介绍了我们自己设计制造的天然Ⅱａ型金刚石光导探测器的结构，原理，制造工艺，实验标定及其在ＩＣＦ实验中软Ｘ光测量中的应用等。     

强脉冲辐射场非平衡硬X辐射测量技术

本文介绍了强脉冲辐射场非平衡硬Ｘ辐射谱测量方法。文中对测量原理、关键定标技术进行了叙述。     

Impregnation of X Zeolite with Alkaline Hydroxide During the Synthesis

Enhancement of the basic properties of the X zeolite with FAU framework has been carried out during synthesis, without further treatment such as ion-exchange or impregnation. Control of the washing stage enables retention of the optimum amount of alkaline hydroxides, which increases the basic catalytic activity of X zeolite in the alkylation of toluene. This alkaline hydroxides neither affect the FAU framework nor the silicon/aluminium molar ratio of the X zeolite. The optimum (Na + K)/Al molar ratio of the improved catalyst was 1.06 corresponding to a washing volume of 200 mL. This X zeolite presented better catalytic activity than a cesium-zeolite prepared by ion-exchange. The presence of hydroxysodalite impurity in the X zeolite increased the amount of impregnated alkaline hydroxides but not the catalytic activity. The present study shows that it is possible to increase the basic properties of the X zeolite directly in the synthesis process.     

马钢2号高炉中修后开炉达产操作实践

对马钢2号高炉中修后开炉达产操作实践进行了总结。通过制定科学的开炉方案,快速提高煤比、降低焦比,实现了顺利开炉、快速达产达效的目标。