超高压大容量铝电解电容器的研制

分析了大功率设备用超高压大容量铝电解电容器的特点,通过研制工作电解液、制订制作工艺及零部件设计方案,研制出的超高压大容量铝电解电容器具有损耗角正切小(tgδ为0.25)、承受纹波电流能力强(100 Hz,2.12～27.8 A)及寿命长的特点,耐久性达到85℃,5 000 h。     

-100kV／10MW全固态刚管调制器

介绍了一种 -10 0kV/10MW全固态刚管调制器的方案和工作原理。简要概述了其各个组成部分、调制器的高电位隔离、IGBT驱动电路、辅助供电以及保护电路的设计与原理。与采用电子管为开关的调制器的主要性能指标进行了对比 ,讨论了这种类型调制器在雷达发射机中应用的前景     

A Bluetooth Based Sensor Network for Civil Infrastructure Health Monitoring

Communicating with sensors has long been limited either to wired connections or to proprietary wireless communication protocols. Using a ubiquitous and inexpensive wireless communication technology to create Sensor Area Networks (SANs) will accelerate the extensive deployment of sensor technology. Bluetooth, an emerging, worldwide standard for inexpensive, local wireless communication is a viable choice for SANs because of its inherent support for some of the important requirements – low power, small form factor, low cost and sufficient communication range. In this paper we outline an approach, centered on the Bluetooth technology, to support a sensor network composed of fixed wireless sensors for health monitoring of highways, bridges and other civil infrastructures. We present a topology formation scheme that not only takes into account the traffic generated by different sensors but also the associated link strengths, buffer capacities and energy availability. The algorithm makes no particular assumptions as to the placement of nodes, and not all nodes need to be in radio proximity of each other. The output is a tree shaped scatternet rooted at the sensor hub (data logger) that is balanced in terms of traffic carried on each of the links. We also analyze the scheduling, routing and healing aspects of the resulting sensor-net topology.     

Flash器件中氧化硅/氮化硅/氧化硅的特性

对普遍采用的氧化硅/氮化硅/氧化硅( ONO)三层复合结构介质层的制备工艺及特性进行了研究分析,研究了ONO的漏电特性以及顶氧( top oxide)和底氧( bottom oxide)的厚度对ONO层漏电的影响.结果表明,采用较薄的底氧和较厚的顶氧,既能保证较高的临界电场强度,又能获得较薄的等效氧化层厚度,提高耦合率,降低编程电压.     

Magnetic Properties of Fe-Doped Rutile

Ball-milling method was applied to dissolve Fe into titanium dioxide (TiO₂). X-ray diffraction indicated the starting anatase changed to a rutile-type structure with oxygen deficiency after ball milling. Transmission electron microscopy and X-ray absorption experiments were conducted to examine the possible existence of magnetic impurities in the ball-milled powders after they were leached in HCl solutions. Temperature dependence of the resistivity shows semiconducting behavior and the magnetic hysteresis loops at 5 and 300 K exhibit ferromagnetic characteristics. Fe-doped TiO₂ films were also prepared by pulsed laser deposition. The magnetic properties of the films are discussed.     

Fracture toughness of PAN-based carbon fibers estimated from strength-mirror size relation

Fracture toughness (K_IC) of representative high-strength type PAN (polyacrylonitrile)-based carbon fibers, Torayca™ T300 and T800H, with or without artificial surface defects, were estimated to be ca. 1 MPam^1/2 from the tensile strength vs. fracture mirror size relation, assuming a constant crack-to-mirror size ratio. The corresponding critical energy release rate (Γ) was ca. 7.4 J m⁻², which was close to the value derived from the reported surface energies for a graphite crystal. Similar K_IC values were obtained for the old-type PAN-based carbon fibers from the reported data by the use of the present estimation procedure.     

Field Static Load Test on Kao-Ping-Hsi Cable-Stayed Bridge

Field load testing is an effective method for understanding the behavior and fundamental characteristics of a cable-stayed bridge. This paper presents the results of field static load tests on the Kao-Ping-Hsi cable-stayed bridge, the longest cable-stayed bridge in Taiwan, before it was open to traffic. A total of 40 loading cases, including the unit and distributed bending and torsion loading effects, were conducted to investigate the bridge behavior. The atmospheric temperature effect on the variations of the main girder deflections was also monitored. The results of static load testing include the main girder deflections, the flexural strains of the prestressed concrete girder, and the variations of the cable forces. A three-dimensional finite-element model was developed. The results show that the bridge under the planned load test conditions has linear superposition characteristics and the analytical model shows a very good agreement with the bridge responses. Further discussion of deflection and cable forces of the design specifications for a cable-stayed bridge is also presented.     

Extracting Light from Polymer Light‐Emitting Diodes Using Stamped Bragg Gratings

In this paper, we describe a method for increasing the external efficiency of polymer light‐emitting diodes (LEDs) by coupling out waveguided light with Bragg gratings. We numerically model the waveguide modes in a typical LED structure and demonstrate how optimizing layer thicknesses and reducing waveguide absorption can enhance the grating outcoupling. The gratings were created by a soft‐lithography technique that minimizes changes to the conventional LED structure. Using one‐dimensional and two‐dimensional gratings, we were able to increase the forward‐directed emission by 47 % and 70 %, respectively, and the external quantum efficiency by 15 % and 25 %.