Trifluoromethanesulphonic acid catalysed transalkylation between tetrabromobisphenol-a and toluene for the production of 2,6-dibromophenol

The preparation of 2,6-dibromophenol is described. This compound, useful as raw material for brominated poly(phenyleneoxide) and pyrogallol or derived pharmaceuticals/pesticides, was prepared in 80% (isolated) yield by a transalkylation reaction between tetrabromobisphenol-A and toluene. The catalyst, trifluoromethanesulphonic acid, can be simply recovered and recycled. Perfluorinated resin sulphonic acid (NAFION-H®, DuPont) did not effectively catalyse this transalkylation.     

Preparation and characterization of oxygen deficient perovskites,BaBiO3−x

Oxygen nonstoichiometry in the distorted perovskite BaBiO₃ has been studied by thermogravimetric analysis using controlled oxygen pressures. Three distinct regions of nonstoichiometry are observed with composition ranges which narrow as the temperature is lowered. Samples isolated from each region were shown by powder X-ray diffraction to retain the perovskite subcell but show different types of framework distortion. Low temperature reoxidation of the oxygen deficient phases is also described.     

担载型含稀土三组份体系在二氧化碳甲烷化反应中的催化性能

用浸渍法制备了一系列氧化锆担载的含稀土Ⅷ族金属催化剂，对其在二氧化碳甲烷化过程中的催化活性作了研究，并用漫反射紫外可见光谱，ＦＴＩＲ等手段对催化剂作了表征。结果表明，含稀土新型催化剂具有催化活性高，目标产物选择性好等优点；稀土主要以氧化物形式存在于催化剂表面，参与对氢及表面含碳物种的吸附及活化；含稀土三组份催化剂的活性与所添加稀土三价离子的４ｆ电子数有关。     

The generation of surface roughness during slurry erosion-corrosion and its effect on the pitting potential

Results of experiments performed to isolate the effect of surface roughness generated during slurry erosion-corrosion of 304L stainless steel are presented. Surfaces prepared by grinding to different finishes show that increasing the roughness lowers the pitting potential in chloride solution. Subsequent erosion by an aqueous sand slurry then alters this pitting potential (E_p), as measured in the solution phase alone, in a manner dependent on the initial surface roughness. Surfaces which were initially rougher show a pronounced rise in _p after erosion, while those with an initially smoother finish show a fall in E_p after erosion. Measurement of E_p during erosion-corrosion does not fit either process, with values of _Ep lower than those predicted from the surface roughness alone.     

使用Visual C+ +实现串行通讯

以VisualC 为工具，探讨了在RS-232C接口协议下DTE设备之间通讯的实现问题。     

碳纳米管及稀土元素钇(Y)对高Ni含量Ti(C,N)基金属陶瓷组织与性能的影响

研究了不同含量的碳纳米管及0.8%稀土Y对高Ni含量Ti(C,N)基金属陶瓷组织性能的影响.将不同成分的试样分别于1400℃、1410 ℃、1420℃真空烧结,测试抗弯强度、洛氏硬度,观察背散射电子形貌、断口形貌并做能谱分析.结果表明,加入质量分数(下同)为0.8%Y及0.3%～1.0%的碳纳米管时,碳纳米管含量为0.5%的组织较均匀,芯壳结构明显,抗弯强度及硬度均较高.     

曲轴R处缺陷的超声探伤及定位问题的研究

针对曲轴R处缺陷的探伤和定位问题进行了探讨和研究,并设计了能对缺陷进行实时定位的程序.     

国产气相聚乙烯浆液催化剂的工业应用

本文简要阐述了北化院BCS01和上海院SLC-S两种国产气相聚乙烯浆液催化剂的性能、催化剂结构,在Unipol聚乙烯工业装置上应用结果,以及和进口同类催化剂UCAT-J的性能比较。     

High resolution XPS characterization of chemical functionalised MWCNTs and SWCNTs

High resolution XPS analysis of chemical functionalised multi-wall carbon nanotubes (MWCNTs) and single wall carbon nanotubes (SWCNT) was done with ESCA300 (overall instrument resolution of 0.35 eV). Information to the degree of functionalisation was ascertained by argon ion bombardment of the samples followed by XPS analysis to detect the functional groups, the percentage atomic concentration of various elements present and whether or not the detected functional groups imposed a chemical shift on the CNT atoms. The results show that true chemical functionalisation was achieved and by argon ion bombardment these functional groups can be altered relative to the C 1s carbon atoms of the CNT. The choice of chemicals used for functionalisation, the techniques employed and the types of nanotubes treated are important factors in chemical characterisation. The carbon atom on the nanotube ring to which the functional group (atom) is bonded, the chirality of the CNT, the electronegativity of the functional group, the bond type and whether the CNT is single-wall or multi-wall, or cut (short) could play a role in determining the chemical shift on the CNTs atoms. These investigations are relevant to chemical functionalisation of carbon nanotubes for various applications for example DNA sensors and other biomedical sensors.     

New catalyst systems for the polymerization of acetylene

The catalytic activities of WCI₆Ph₄Sn, MoCl₅Ph₄Sn and tetrabenzyltitanium were examined in the polymerization of acetylene. The structure, morphology and electrical conductivity of the doped and non doped polyacetylene were also studied.