Role of La2O3 in Pd-Supported Catalysts for Methanol Decomposition

Systems of Pd supported on various La₂O₃-modified -Al₂O₃ and CeO₂–Al₂O₃ catalysts were tested for catalytic methanol decomposition and characterized by means of XRD, BET, TPR, H₂-chemisorption and CO–FTIR. The addition of lanthanum significantly improved the selectivity of CO and H₂ for all the catalysts but showed a different influence on the catalytic activity in two systems. Methanol conversion decreased on La₂O₃-modified Pd/-Al₂O₃ catalysts, in line with the reduction of Pd dispersion, while the addition of La₂O₃ improved the dispersion of Pd and reinforced Pd–CeO₂ interaction for La₂O₃-modified Pd/CeO₂–Al₂O₃ catalysts, which resulted in a high production rate of CO and H₂. Thus, a synergistic effect between CeO₂ and La₂O₃ was observed on -Al₂O₃-supported Pd catalyst for methanol decomposition.     

The effect of fibre-matrix interactions on structure and property changes during the fabrication of unidirectional carbon/carbon composites

This paper reports the systematic characterisation of changes in the structure and properties of a series of unidirectional carbon-carbon composites at key stages of processing. The composites were fabricated from PAN-based carbon fibres (surface treated and untreated) and two carbon matrix systems (graphitising and non-graphitising). The effects of matrix shrinkage, together with thermal expansion mismatch and interfacial bonding, established the composite structure and hence the composite properties. The morphology and interconnectivity of the shrinkage cracks, the strength and nature of the fibre-matrix interfacial interaction and the development of matrix texture were identified as key structural features. These features were characterised and their effect on subsequent processing stages (densification) and composite properties was determined.     

复合材料纤维缠绕成型CAD/CAM相关技术研究

纤维缠绕成型是制造高强度复合材料制品的一种重要的工艺方法，将CAD／CAM方法应用其中可以大大提高生产效率，降低设计成本。本文提出了纤维缠绕CAD／CAM系统的总体方案，并对其中缠绕数学模型、线型优化、丝嘴轨迹生成等量要组成部分进行了分析与研究，为CAD／CAM系统的开发奠定了理论基础。     

Deformation Dynamics of a Reactive Medium During Gasless Combustion

Deformation during gasless combustion of 5Ti + 3Si and Ti + C samples was studied experimentally. The dynamics of motion of the material in a gasless combustion wave was studied using highspeed video recording (500 frames/sec) with a spatial resolution of the order of 10 m. It was shown that behind the combustion front, the medium was first expanded and then compressed. The dimensions of the expansion and compression zones were determined.     

Physical characteristics of sweet potato pulp/polycaprolactone blends

Sweet potato pulp (SSP) obtained as a by‐product from starch extraction was blended with polycaprolactone (PCL) to prepare a biodegradable plastic material. In the blends, PCL was used as a reinforcing agent. The SPP/PCL blends were prepared by compression‐molding under high temperature and pressure, at different SPP/PCL ratios, and the mechanical properties of the molded specimens were tested. Matrix structure and thermal properties were measured by using a Fourier transform infrared (FTIR) spectrophotometer, scanning electron microscope (SEM), differential scanning calorimetry (DSC), and thermogravimetric analyzer (TGA). Mechanical properties (tensile and flexural properties) were also measured to find the most suitable ratio in a SSP/PCL blend. During compression molding of the SPP/PCL blends under high pressure and temperature, chemical reaction occurred between SPP and PCL, and thus, thermal stability and mechanical strength of the blends increased and water uptake decreased. Also, by increasing the PCL content in the blend, the matrix in the blend became more homogeneous, and consequently, mechanical strength of the molded specimen increased. At 7/3 or 6/4 weight ratio of SSP/PCL, water uptake of the molded specimen became substantially less than that at 8/2. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 861–866, 2004     

Pd/Al2O3催化剂上CH4选择性还原NO的研究

考察了Pd/Al₂O₃、In/Al₂O₃和Co/Al₂O₃对甲烷选择性还原NO的催化活性。结果表明，采用浸渍法制备的Pd/Al₂O₃、In/Al₂O₃和Co/Al₂O₃三种催化剂，在有氧气氛下，用CH₄作还原剂催化还原NO时，Pd/Al₂O₃催化剂的活性最佳，热稳定性好，在550 ℃，用CH₄选择还原NO，Pd/Al₂O₃催化剂表现出较强的催化能力，NO的转化率达到100%。在高空速实验中，该催化剂亦表现出较高的活性，其活性顺序为Pd/Al₂O₃>In/Al₂O₃>Co/Al₂O₃。实验研究了助催化剂、氧含量以及空速对Pd/Al₂O₃催化剂活性的影响。     

Desulfurization of commercial fuels by π-complexation: Monolayer CuCl/γ-Al2O3

Monolayer CuCl/γ-Al₂O₃ sorbent was studied for desulfurization of a commercial jet fuel (364.3 ppmw S) and a commercial diesel (140 ppmw S). The sorbent was prepared by means of spontaneous monolayer dispersion methods. Deep desulfurization (sulfur levels of <1 ppmw) was accomplished with this sorbent using a fixed-bed adsorber. The CuCl/γ-Al₂O₃ sorbent was capable of removing 6.4 and 11.2 mg of sulfur per gram for jet fuel at breakthrough (at <1 ppmw S) and saturation, respectively. The same sorbent was capable of removing 0.94 and 1.8 mg of sulfur per gram for BP diesel at breakthrough and saturation, respectively. The difference in sulfur capacities for jet fuel and diesel was apparently caused by the difference in concentrations of strongly binding compounds, such as nitrogen heterocycles, heavy (polynuclear) aromatics and fuel additives. In comparison with CuCl/γ-Al₂O₃, Cu(I)Y zeolite has higher sulfur capacities but is less stable and can be easily oxidized to Cu(II)Y by fuel additives (such as oxygenates) and moisture and consequently loses π-complexation ability. However, all these cuprous π-complexation sorbents selectively adsorb thiophenic compounds over aromatics and olefins (as predicted by the high separation factors), which resulted in the observed desulfurization capability. A feasibility study is shown for efficient regeneration of CuCl/γ-Al₂O₃ using ultrasound at ambient temperature. Possible problems associated with desulfurization using π-complexation sorbents for commercial fuels are discussed.     

CO2 effect on activity and stability of NOx storage reduction catalysts

A catalyst for NO_x storage/reduction was prepared to improve the activity of Ba–Pt/γ-Al₂O₃ by replacing Ba with a mixture of Ba and Mg. The catalyst was prepared by impregnating Pt and then co-impregnating Ba and Mg (Mg:Ba molar ratio = 1) on commercial γ-Al₂O₃. The tests have been carried out in the presence of CO₂ at temperatures between 200 and 400 °C in order to understand the role of both the feed and various alkaline-earth metals. The storage capacity of the two catalysts was different like the mechanism in the reduction process.     

Deposition of CoO onto MoO3/Al2O3 hydrodesulfurization catalysts by solvent assisted spreading

Solvent assisted spreading of CoO over monolayer MoO₃/Al₂O₃ catalysts has been studied. CoCO₃ · Co(OH)₂ and CoCO₃ reacted with MoO₃/Al₂O₃ in water slurries. CoO deposition over MoO₃/Al₂O₃ extrudates was followed by EPMA. In the set of eleven MoO₃/Al₂O₃ catalysts, the amount of CoO adsorbed was roughly proportional to the surface area of MoO₃ monolayer. The adsorbed Co species efficiently enhanced the HDS activity.     

改性木粉/PVC复合材料的研究进展

概述了PVC木塑复合材料的发展和背景与性能。简述了木质材料的性质和木粉改性的方法,如物理方法和化学方法。介绍了木塑复合材料的生产流程、成型方法(模压成型、挤出成型、注射成型及其成型设备,讨论了对工艺参数的一些要求。指出目前国内PVC木塑复合材料发展存在的一些问题,并指明了PVC木塑复合材料的应用前景。